Question about 1999 Toyota Camry Solara

Open Question

Where is the blend air door actuator on a 99 Toyota solara

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: front grill on toyota solara

That is correct - it worked for me - now the questions is - How do I remove the old logo ?

Posted on Apr 25, 2009

Ad

Brian Anderson

  • 389 Answers

SOURCE: my 2000 4 runner limited blows cool to lukewarm

Have you checked your thermostat to make sure it isn't stuck open?

Posted on Oct 10, 2009

JIMMY

  • 1374 Answers

SOURCE: install motor/regulator to 2000 camry solara

It easy ! You need a philips2_bing.gif and flat screw driver,8" X 4" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch panel ( aka master switch panel) with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder ( driver or front passenger door) in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the six gold2_bing.gif bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.
Comments:

Posted on Apr 22, 2010

2wiseman08

Rick

  • 14 Answers

SOURCE: air blend door

First check the connections at the blend dial if it is good there then take a look at the control assembly circuit board for broke or loose wires.

Posted on Jul 08, 2012

Kristoffer Martin

  • 293 Answers

SOURCE: how do I replace a 2000 Toyota Avalon blend door actuator?

The blend door actuator is one of the heating control units found in the center console. Purchase a console tool and remove the plastic console cover after dismantling the front of the heating control. There should be a series of clips that hold the plastics on. Once you get to this point you'll want a tray to keep track of screws. Unscrew the mounts for the control unit and pull them out, taking care not to damage the ribbons or cables connecting the unit to the heating and cooling unit. Unplug the offending actuator from the control unit and plug the new one in. Then reverse process to reinstall the control unit and plastics.

You can find diagrams on google, and the actuator on amazon.com or rockauto.com.

NOTE: Caution; make sure to disconnect the battery to prevent potential electric shock.

Posted on Jan 28, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the blend door for the heater/A/C for a 1998 Toyota Tacoma 6V


Not sure if this will help.
I have changed a couple blend door actuators, my newer cars were controlled electrical. My Safari was controlled with vacuum line. I could not find where yours is for sure but all that I have changed were behind the glove box and there were two actuators (one on left and the other to the right of the glove box) one was blend door. the last one I changed was a Chrysler 200 it was behind the glove box on the right. The video below FORD is behind glove and to the left side.
How To Install Replace Air Temperature Door Actuator Explorer Mountaineer 98-01 1AAuto.com
https://www.youtube.com/watch?v=g-36aM360V8

Sep 17, 2018 | Toyota Cars & Trucks

1 Answer

Changing blend door actuator on 2004 toyota 4runner


The actuator motor is on the passenger side, under glove box to the left. Pull it out and make sure the blend door moves freely, if not the dash must come out and the door be replaced or the new actuator will fail.

Jul 05, 2017 | Toyota Cars & Trucks

1 Answer

How do i fix a stuck blend door on 2010 dodge nitro?


I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Feb 17, 2015 | 2010 Dodge Nitro

1 Answer

99 300m heater blown cool air


Air Temperature Control Blend Door Failure No Heat

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Nov 01, 2012 | Cars & Trucks

1 Answer

My 2004 Avalanche ' heating system will not heat. No matter what the setting it either blows no air or cold air and it is 25 degrees outside so this is a problem. The engine is up to temp and I have tried...


The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation
  1. Remove the floor air outlet duct extension (1) from the floor duct (2).

    jturcotte_393.gif

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)


Disconnect the electrical connection at the blend door actuator (#10 in pic below). jturcotte_394.gif

Fig. Blend door actuator and related components


Remove the blend door actuator mounting screws from the HVAC module.


Remove the blend door actuator as an assembly with the actuator cam.
jturcotte_396.gif

Fig. Remove the blend door actuator mounting screws from the HVAC module



To install:

  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam

  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).

  3. Connect the electrical connection at the blend door actuator (10).
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).


Picture of actuator:


jturcotte_57.jpg

Dec 07, 2010 | 2004 Chevrolet Avalanche

2 Answers

1999 Silverado - cannot get the temperature to switch from cool air to warm air when turning the knob to heat.


The temp blend door, or blend door actuator may be faulty. You can check this by watching the movement of the blend door actuator while you turn the temp selector knob. If the actuator is working, then it may be the blend door, or blend door lever broken. If these are ok then the control head may be faulty.

Oct 18, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
1999 Toyota Camry Solara Logo

Related Topics:

1,427 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...