How much torque should i apply on the crankshaft and head bolts of a 1996 corolla sprinter 5AFE

Ok, the main cap bolts (crankshaft) vary depending on 6 or 12 pt. head. 6 pt. head is just 14 ft. lbs. 12 pt head on the bolt requires it to be tightened in 4 stages, 16 ft. lbs., then 32 ft. lbs., then turn additional 90 degrees, then another additional 90 degrees. The connecting rod cap bolts (pistons) get 2 stages, 15 ft. lbs. then additional 90 degrees.

A Chiltons/Haynes repair manual from your local auto parts store that covers your year/make/model has all of your answers under the "engine rebuild" heading.

From FSM:

B: INSTALLATION
1) Install the crankshaft pulley.
2) Install the pulley bolt.
To lock the crankshaft, use ST.
ST 499977400 CRANKSHAFT PULLEY
WRENCH
(1) Clean the crankshaft pulley thread using an
air gun.
(2) Apply engine oil to the crankshaft pulley bolt
seat and thread.
(3) Tighten the bolts temporarily with tightening
torque of 44 N·m (4.5 kgf-m, 33 ft-lb).
(4) Tighten the crankshaft pulley bolts.
Tightening torque:
127 N·m (13 kgf-m, 94.0 ft-lb)

Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
- Install the plate washer to each cylinder head
bolt.
- Using Torque wrench, install and uniformly tighten the ten
cylinder head bolts in several passes.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)

Commonly Asked Torque Specs in foot pounds
The main bolts have a torque of 76 lb.-feet and the cylinder head bolts have 62 lb.-feet of torque. The cylinder head studs have 70 foot-lbs of torque, the cam timing gear have lb.-feet of torque, and the cam bearing bolt has 14 lb.-feet of torque.

Crankshaft Torque Specs

• The stock rod bolts have 46 lb.-feet of torque and the ARP rod bolts have 50 lb.-feet of torque. The crankshaft pulley has 116 lb.-feet of torque, while the flywheel has 80 lb.-feet of torque.
  

Other Torque Specs

• The intake manifold and exhaust manifold have 33 lb.-feet of torque each and the oil pan bolts have 9 lb.-feet of torque. The cam timing gear has 58 lb.-feet of torque and the cam bearing bolt has 14 lb.-feet of torque. One set of timing cover bolts have 9 lb.-feet of torque and another set has 29 lb.-feet of torque
  

1996 Isuzu Truck Hombre 2.2L SFI 4cyl

Fig.: Cylinder head bolt torque sequence-2.2L engine

Apply a coating of 1052080 or equivalent sealer to the cylinder head bolt threads. Install the cylinder head bolts (within 15 minutes of sealer application), then tighten them in the proper sequence first to a torque of 46 ft. lbs. (63 Nm) for long bolts or to 43 ft. lbs. (58 Nm) for short bolts and then tighten all bolts an additional 90 degree turn using a torque angle meter.

Hope this helps (remember to rate this answer).

should come with the package containing the head gaskit or upper cylinder kit.Mostly at the back or printed inside the package.

Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top

Depending on your location, 10W-30 is fine.