Question about 2001 Hyundai Tiburon
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
If it doesn't have an automatic belt tensioner there will be an adjustment screw on either the alternator or power steering pump (possibly both if there are two belts). Loosen the two mounting bolts securing the accessory (ie: alt or p/s pump) and tighten the screw. Once adequate tension is on the belt tighten the mounting bolts.
Sometimes the adjustment is on a seperate pulley and not one of the accessories. If this is the case, loosen the center bolt on the pulley and tighten the adjustment screw. Once tight, tighten the center bolt.
If you have an automatic tensioner there are no adjustments to make the belt tighter.
Posted on May 09, 2009
It is a 2.0L (the delta blocks weren't in tibs until '03). You have to remove the timing belt tensioner, and then you can remove the bolts for the water pump. I would strongly recommend not only taking careful precaution not to disturb the orientation of the gears in this process, but also to replace the timing belt and water pump at the same time. You don't want to go through this process all over again do you?
Posted on May 27, 2009
1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.
I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.
Posted on May 27, 2009
Pop the hood and you should see two dials (hex shaped plastic screws) on each of the headlight assemblies. One is for your high beams and one is for your low beams. You'll need to measure from the ground up to the center of your bulb and make that marking on the wall for each of your bulbs (so four marks). Then park about 30 feet away from the wall (make sure you're on a level surface that's level with the wall base. If the light says VOR, then the top of the brightest area of the light should line up with the mark. if it says VOL, then the top of the brightest area of the light should line up two inches below the mark.
Posted on Aug 21, 2009
2001 Hyundai Tiburon 2.0L MFI DOHC 4cyl
The Fuel Filter is located Under hood, passenger side, front side of strut tower, mounted on fenderwell.
I hope help you with this, remember rated this help.
Posted on Sep 10, 2009
Testimonial: "THANK YOU !!!!!"
Tips for a great answer:
Dec 21, 2015 | 2003 Hyundai Tiburon
Jan 22, 2011 | 2001 Hyundai Tiburon
Apr 13, 2010 | 2001 Hyundai Tiburon
Nov 08, 2009 | 2001 Hyundai Tiburon
Aug 11, 2009 | 1998 Hyundai Tiburon
Jun 13, 2009 | 2001 Hyundai Tiburon
Apr 06, 2009 | 2001 Hyundai Tiburon
Nov 10, 2008 | 2004 Hyundai Tiburon
Mar 15, 2017 | 2001 Hyundai Tiburon
345 people viewed this question
Usually answered in minutes!