Front drivers seat removal - 2004 Jeep Liberty

transfer case shift control module
Transfer Case Shift Control Module Replacement
Removal Procedure
Important: The transfer case shift control module (TCCM) is located under the drivers seat carpet. For removal purposes, access the TCCM from underneath the carpet.
Remove the drivers bucket seat or split bench seat. Refer to Front Seat Replacement - Bucket or Split Bench Seat Replacement.
Remove the left front sill plate. Refer to Front Side Door Sill Plate Replacement.
Remove the left hinge pillar. Refer to Body Hinge Pillar Trim Panel Replacement - Left Side.
Remove the left center pillar. Refer to Center Pillar Lower Trim Panel Replacement.

Remove seat track plastic covers. Remove seat bolts

Move the seat all the way forward and remove the two bolts going into the cross bar in the back. Move the seat all the way back and remove the plastic covers where the front feet of the seat meet the floor. Remove the two bolts going into the floor. Lean the seat back and disconnect the electrical connectors.Lean the seat sideways so that the outside part is facing up and remove the nut holding the seatbelt to the seat and take off the seatbelt. The seat is now free to be removed from the car.

Head Restraints Removal

1. Unscrew front seat head rest guide rod retainers (610A18) .
   

1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
   

1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
   

Installation

1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
   

1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
   

1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
   

1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .
   
   Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
   

1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .
   

there are plastic covers over the front bolts that hold the seat to the floor remove the screws the hold these covers on then remove the two front bolts under these covers then move the seat all the way forward and you should be able to see the two bolts that hold the rear of the seat to the floor pan there could be covers on these to remove the bolts and then tip the seat forward and unplug the wire connector for the power seat(if it has this option).hope this helped

SECTION 501-10: Seating 1998 Escort/Tracer Workshop Manual REMOVAL AND INSTALLATION Seat —Front Removal
NOTE: Driver side seat shown, passenger side seat similar.

1. Slide the seat to its rearward position.

1. Remove the front seat track to floor front bolts.

1. Slide the seat to the forward position.

1. Remove the front seat track to floor rear bolts.

1. Disconnect the safety belt warning indicator switch electrical connector.

1. Remove the front seat.

easy.Remove the mounting bolts at the front and rear of the seat 2 front,,2 rear seat should just come out

4 bolts is fairly easy remove the rear first with the seat all the way forwards and then put seat all the way back then 2 in the front remove them ..tilt the seat back and if there is any wire harness disconnect them as well ...reverse process for re-installation

Hi,

2001 Dodge Caravan Performance Features -3,301 cc 3.3 liters 6 V engine with 93 mm bore, 81 mm stroke, 9.3 compression ratio, overhead valve and two valves per cylinder
-Unleaded fuel
-Fuel economy EPA highway (l/100km): 9.8
-Multi-point injection fuel system
-Main 76 liter unleaded fuel tank
-Power: SAE and 134 kW , 180 HP @ 5,000 rpm; 210 ft lb , 285 Nm @ 4,000 rpm
2001 Dodge Caravan Handling & Driving Features -ABS
-Two disc brakes including two ventilated discs
-Spacesaver steel rim under body spare wheel
-Strut front suspension with stabilizer bar independent with coil springs , beam rear suspension with stabilizer bar rigid with leaf springs
2001 Dodge Caravan Exterior Features -Body side molding
-Front and rear body color bumpers
-Driver and passenger power heated black door mirrors
-External dimensions: overall length (mm): 4,803, overall width (mm): 1,996, overall height (mm): 1,750, wheelbase (mm): 2,878, front track (mm): 1,600, rear track (mm): 1,626 and curb to curb turning circle (mm): 11,460
-Complex surface lens halogen bulb headlights
-Double sliding minivan side door
-Remote control operation opening rear ¼ windows
-Metallic paint , gloss paint , pearl paint
-Fixed rear window
-Tinted glass on cabin, rear and side
-Weights: curb weight (kg) 1,842, gross trailer weight braked (kg) 907 and max legal load (kg) 772
-Windshield wipers with variable intermittent wipe
2001 Dodge Caravan Interior Features -Air conditioning with rear outlet
-Fixed mast antenna
-Manufacturer's own audio system
-Automatic drive indicator on dashboard
-Below seat storage under passenger seat
-Cargo capacity: all seats in place (liters): 433, all seats removed (liters): 4,154 and third row seats removed (liters): 1,291
-Clock
-Dashboard full console with open storage box
-Delayed/fade courtesy lights
-Cruise control
-Front seats, rear seats and 3rd row seats cup holders
-Door ajar warning
-Door pockets/bins for driver seat and passenger seat
-Floor covering: carpet in load area
-Driver and passenger front airbag
-Bucket seat
-3-point reel height adjustable front seat belts on driver seat and passenger seat
-Front seat center armrest
-Glove compartment
-Height adjustable two head restraints on front seats, rear seats and 3rd row seats
-Internal dimensions: front headroom (mm): 1,011, rear headroom (mm): 998, front hip room (mm): 1,440, rear hip room (mm): 1,722, front leg room (mm): 1,031, rear leg room (mm): 930, front shoulder room (mm): 1,588 and rear shoulder room (mm): 1,643
-Low fuel level warning
-Low washer fluid level warning
-Internal button power locks
-Power steering
-Front power windows with one one-touch
-Front reading lights
-3-point reel height adjustable rear seat belts on driver side and passenger side
-Bench one-piece two rear seats
-Rear view mirror
-Upgraded cloth/velour seat upholstery
-Seating: seven seats
-Six speakers
-Plastic steering wheel
-Tachometer
-3-point reel third row seat belts on driver side , 3-point reel third row seat belts on passenger side , lap static third row seat belts on center side
-Front facing bench removable one-piece third row seats with capacity three
-Driver and passenger vanity mirror
-Ventilation system with recirculation setting
Thanks.

yes you can remove the center seat but it involves pulling the front pass seat out then taking the two right hand bolts out of the drivers seat then it will pull out then just use the same bolts to reinstall your driver a pass seat