Where is my egr valve location Mitsubishi Galant 2004

Location and information

https://www.justanswer.com/mitsubishi/7khod-mitsubishi-galant-2003-car-showing-p0441.html

The purge valve is located in the vacuum line between the fuel vapor containment canister and the intake manifold.

Mitsubishi Galant Purge Valve Replacement Cost Estimate

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk03mmyVCEHrQQIm9xoiMRqeAooKTvg%3A1612984487148&ei=pzAkYNvBCOWi_QbLr5XYDQ&q=03+mitsubishi+gallant+purge+valve+location

..

https://www.google.com/search?q=Need+to+no+where+mass+air+sensor+located+on+a+2002+cavalier+2.2+motor&biw=1363&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwidypiQ58LQAhXJ7iYKHevTAvsQsAQIHQ#tbm=isch&q=Where+is+shift+solenoid+on+Mitsubishi+Galant+2004+located+%3F!

Hope this helps

Have you tried erasing the code with a vehicle scanner?

not posted if this is a diesel or a petrol engine but it will be between the inlet manifold and the exhaust manifold ,sorry if this vague but iam not a dealer fitter working on only one brand but a back street cowboy who works on anything and the secret here is to look first and follow all the pipes to see where it is

Hello! None are specified...Tighten as you would any other bolt...Guru..saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

I cannot tell you exactly where it is on this model ... however, you will find the Exhaust Gas Recirculation valve between the exhaust manifold and the fuel input area of your car - fuel injection or carb. It will be the size of a screw driver handle. If you are returning from a trip ... it will be VERY HOT.

Thanks for your visit @ FixYa.com today.

first make sure egr valve works.with engine running aply vacum to valve, if idle drops,valve is ok.if not you may have a bad valve or possible carboned up egr passage.

Check for

vacuum leaks on intake manifold,

the air tube between the air filter.

intake manifold vacuum hose.

===
clean throttle plate with Berryman carburator cleaner

SEE sample picture HERE
===

Also remove carbon built up behind the EGR valve and the EGR passage tube.

===

Vacuum leak WILL offset the intended 14.7 to 1 air fuel ratio.

More un-metered air (leaks) will lean out the fuel mixture.

Use small amount of Berryman carb clearer at potential air leak area will help you identify trouble spot.

At idle,just spray and listen for the RPM surge.

The in-rush of carb clearer will increase the RPM on the motor.

Record the problem spot(s) and address it later.

===

EGR carbon built up require 2+ hours to clean from start to finish.

You will need a new EGR base gasket before your start.

Locate and remove the EGR valve after the vehicle is cool down.

Carefully record the connector and vacuum line (for older vehicle) location by drawing an easily to follow diagram.

Remove the EGR valve.

Inspect the location of the carbon built-up inside the valve and the EGR passage tube.

SOAK these areas with WD-40 spary.

You will need a small screwdriver,cloth hanger and lot of newspaper and time to get this cleaning done right.

RE-SOAK the carbon and let it sit for over-night will also help.

One the last round,pass a shop vacuum of the EGR valve and the passage pipe.

Install the new EGR gasket and connectors.

Allow the vehicle to warm up outdoor to burn up any remaining WD-40.


Take it for a test drive.


Please rate my answer if it's useful to you.


Cheers,

Mustgo

Should be close to your throttle body, usually held by 2 big screws, disconnect the hose coming from egr valve, and replace with a new one, dont lose the gasket.

It is on the firewall just behind the engine, to replace it you need to detach the vacuum hose, remove the two EGR valve mounting bolts, remove the EGR valve from the intake manifold and then put in the new one.

Thanks for using FixYa - a good rating is appreciated for answering your FREE question.