1996 Lexus ES 300 Logo

Related Topics:

S
Sharon Moody Posted on Jan 15, 2017

Fix p1500 starter signal circuit malfunction, 1996 es300 lexus

Code shows up with check. Car has been failing to start.

5 Related Answers

Anonymous

  • 1861 Answers
  • Posted on Nov 13, 2008

SOURCE: car codes

When you have P0440, P0441 and P0446, it is a very good bet that the fuel cap was loose, or the fuel cap rubber seal is compromised. You will get all three of those codes every time that the cap is loose. Always make sure that the fuel cap is as tight as you can get it after you refuel.

Ad
mecanica03

ROBERT GARCIA

  • 926 Answers
  • Posted on Apr 21, 2009

SOURCE: Check Engine Light came on with code p0420. Dealer wants $3900 to fix "b2 manifold and front pipes. Does this make sense. Are their better alternatives. I left the dealership without fixing it and the

if your car no present any problem i think that mechanic is a thieft.

Sometimes the fuel have mixtures that make the check light on , to reset disconnect the negative battery few minutes, no go more to this mechanic,good luck

Anonymous

  • 350 Answers
  • Posted on Oct 29, 2009

SOURCE: 2002 Lexus ES300 Check Engine Light

You can disconnect your battery for a short period of time, 5-10 minutes should do it. There is no guarantee that the check engine light will not come back on in time, but it will make it go away at least temporarily.If you go to Autozone, 99% of the time they will hook up a code reader and diagnose your problem. It may be a minor and/or inexpensive fix. Please vote appropriately and leave feedback. I hope this helps and good luck.

Testimonial: "I'll give it a try!! Thank you- "

Anonymous

  • 2 Answers
  • Posted on Nov 12, 2009

SOURCE: 1996 Lexus ES300 replacing starter

the starter is in the wright side of the motor under the cruis controls. remove the black cover and youll see it....

Anonymous

  • 1 Answer
  • Posted on Feb 12, 2011

SOURCE: Lexus ES300 outside temperature gauge not working

I also have the same problem, I would also be happy with a diagram of the location of the sensor.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I fix code 13 engine speed sensor Above 1000 rpm

Clearing the codes is simple that is done by removing the fuse of the EFI from junction box 2 for 10 seconds. Make sure to remove the jumper wire and switch the key off before clearing the codes.

Here are some common Lexus vehicles 1990-1995 codes:

Code 12 and Code 13 Rpm signal circuit fault
Code 14 Igniter signal circuit fault
Code 16 ECT control signal fault
Code 21 and Code 28 Main oxygen sensor fault (for ES300; SC300 & GS300 models)
Code 22 Coolant temperature circuit fault
Code 24 Intake temperature sensor circuit fault
Code 25 and Code 26 Air fuel ratio fault (for ES300 & SC300 models)
Code 27 Sub-oxygen sensor circuit fault (for ES300 CA & GS300 models)
Code 31 Low airflow meter voltage (for ES300 and GS300 models)
Code 32 High airflow meter voltage (for ES300 model)
Code 35 Barometric pressure sensor circuit fault (for GS300 & SC300 models)
Code 41 and Code 47 Throttle position sensor circuit fault
Code 42 Vehicle speed sensor circuit fault
Code 43 Starter signal
Code 51 Switch condition signal fault (for ES300; GS300 & SC300 models)
Code 52 Code 52 and Code 55 Knock sensor circuit fault
Code 71 EGR system circuit fault (for ES300; GS300 & SC300 models)
Code 78 Fuel pump control circuit fault (for GS300 & SC300 models)
0helpful
1answer

What is lexus es300 fault code p0340

It is the camshaft position sensor A bank 1 code.
Here are possible causes:
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
2helpful
1answer

I have a 1996 lexus es300 that failed emissions with the following codes: P0100: Mass or volume air flow circuit; P0110:intake air temperature circuit P0135 02 sensor heater circuit (bank 1 sensor1) ...

what was the first code present. that one code will chain react the rest .clear them let them come back on and they will then compare the order
1helpful
1answer

Obd 2 code p0446 on a 1996 lexus es300

Evaporative Emission Control System Vent Control Circuit Malfunction A code P0446 could mean one or more of the following has happened:

  • Faulty vent valve
  • Open, short or excessive resistance on Vent valve control circuit
  • Blockage of vent valve
  • Bad PCM


With a P0446 OBD-II trouble code, here are some things to try:

  • Replace Vent valve
  • Repair open, short, or resistance problem in control circuit
  • Repair open, or short, or resistance problem in power circuit
  • Replace PCM
0helpful
1answer

My 1999 Lexus Es300 shows VSC OFF display for a day or two and then disappears. The problem is intermittent. Sometimes the "Check Engine Light" also comes on. The state emission test showed an...

P1133 LEXUS - Air/Fuel Ratio Sensor Circuit Response Malfunction Bank 1 Sensor 1 Possible causes Faulty Air/Fuel Ratio Sensor Bank 1 Sensor 1 Air/Fuel Ratio Sensor Bank 1 Sensor 1 harness is open or shorted Air/Fuel Ratio Sensor Bank 1 Sensor 1 circuit poor electrical conection Check exaust integrity
3helpful
1answer

1996 Lexus ES300 replacing starter

the starter is in the wright side of the motor under the cruis controls. remove the black cover and youll see it....
0helpful
1answer

After I replace water pump than I start my car

LOOK UNDER THE HOOD. AND CHECK FUEL LINES FOR LEAKS. YOU PROBABLY HIT AGAINST FUEL LINES WHILE REPLACING THE WATER PUMP.YOU NEED TO FIX FAST.FUEL LEAKS IS DANGEROUS.
3helpful
2answers

Lexus es300 won't start

I had a similar experience just the other day, i stopped to get gas and turned the car off and when attempting to turn the car back on nothing would happen. Well, let me rephrase the lights inside and out would work as well as the ac and the radio. My initial train of thought was maybe it was the battery so i went and purchased a new battery which was around $100, I installed the new battery and the car still wouldn't start. Does your car make a clicking noise when you turn the inginition key or is it just silent? If it is silent, you might want to check to see if your starter has burned out. Luckly a friend of a friend does his own mechanical work and was able to remove and replace the starter for me. After the starter was replaced the car started right up and ran perfectly. Not sure where u live but in my area a starter ranges in price from $100-200, but they also charge a core fee ranging from $45+, which can be reimbursed if you bring in your old starter to the store. I would suggest getting a starter with a lifetime warranty as well, but thats just a suggestion.

Hope this helps,

brelic
Not finding what you are looking for?

212 views

Ask a Question

Usually answered in minutes!

Top Lexus Experts

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...