Question about 2006 Chevrolet Colorado

Open Question

I need to change ignition switch on 2006 colorado

Posted by on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
c17hydro

Greg Bernett

  • 2989 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

Ad
huestis_ed

EdCarCal

  • 1083 Answers

SOURCE: I need to change ignition switch on my Chevy Colorado

The ignition switch should be located at the lower part of the steering column and is actuated by the key cylinder. It is difficult to replace (made hard for thieves to get at it).

Posted on Jan 08, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to change ignition switch on my Chevy Colorado


The ignition switch should be located at the lower part of the steering column and is actuated by the key cylinder. It is difficult to replace (made hard for thieves to get at it).

Jan 07, 2017 | 2006 Chevrolet Colorado

1 Answer

2006 colorado head lights do not work low or high beems


check the light control module
check/ replace head light switch

Dec 13, 2015 | 2006 Chevrolet Colorado Crew

1 Answer

Why is the ignition key not turning to start my 2006 chevy colorado? Also the stering column will not lock when turned. this occurred suddenly after parking the vehicle. I am unable to start the ve


I assume you have kids and that's why you want to lock it and keep it secured either your kids jammed something in that ignition switch and messed something up. So I would take a good flash light and peer down into that key ignition hole and see if anything is blocked in there. if so or a bad ignition switch, you need disconnect the battery and remove the bottom dash plate from the steering wheel and you will have to disconnect the ignition cable from the ignition switch and take out the ignition by unscrewing the securing screws that hold that ignition in, best to get a mechanic book made for that make and model.

Sep 28, 2014 | 2006 Chevrolet Colorado

1 Answer

What is the plug gap supose to be for a 2006 chevy colorado 3.5 5 cylinder


change the ignition switch!!!!!! went to the shop six times until they changed the damb switch!!!!

Jun 26, 2009 | 2006 Chevrolet Colorado

1 Answer

Switch odometer from miles to kilometer


If your colorado has a drivers info center you can do it through the dash yourself. It will be in the owners manuel. If it does not have the info center you will need to take it to a dealer and it will take just a few minutes to do with their scan tool. Good Luck

May 29, 2009 | 2006 Chevrolet Colorado

3 Answers

How do I reset the "Oil Change Warning Indication" on colorado


if you have a owners manual read it. try coloradofans.com website and search the forums. i think johnny5846 is right if you don't have a DIC (driver info center). i believe you use the DIC(tripodometer). i don't know the sequence off hand, you can also you can change your lock settings and alarm settings, etc. with the DIC.

Jan 13, 2009 | 2006 Chevrolet Colorado

Not finding what you are looking for?
2006 Chevrolet Colorado Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...