My running lights do not go off when i turn the switch to the off position on a 1998 hyundai sonata

1. Cars
2. Car Maintenance
3. General Car Maintenance
4. How to Program Keyless Entry Remotes in a Hyundai Sonata

How to Program Keyless Entry Remotes in a Hyundai Sonata By Christian Killian, eHow Contributor

• ? Pin
• ? 9
• ? Tweet
• ? Stumble
• ? Share

20Found This Helpful The keyless entry system in your Hyundai Sonata is part of the factory alarm system. If you have to replace a lost or damaged remote, reprogramming will be necessary. The remote is important because not only does it lock and unlock the doors, it also arms and disarms that factory alarm when you open or close your car doors. New remotes are available from any Hyundai dealer. While they will program it for you, you can do it yourself and save a programming fee.
How to Program Keyless Entry Remotes in a Hyundai Sonata(Kleophaus Livingston/Demand Media)

Other People Are Reading

• How to Reprogram Key Fobs Yourself
• How To Replace a Hyundai Sonata Remote

Step 1: Locate the fuse panel under the dash on the driver's side of the car. Just below it is the control module for the factory alarm system. Open the cover on the alarm system control module and locate the memory switch inside.
(Kleophaus Livingston/Demand Media) Step 2: Verify that the switch is in the "Off" position; if it is not, switch it to the "Off" position. This is important for the system to understand what you want it to do when you move to the programming mode.
(Kleophaus Livingston/Demand Media) Sponsored Links

• Download New VersionSnagit 12 Image & Video Capture. Edit & Share. Try Free Today!
  techsmith.com

Step 3: Insert the key into the ignition of your Sonata and turn the key to the "On" position. Wait for 60 seconds, then move the memory switch inside the control module to "Set."
(Kleophaus Livingston/Demand Media) Step 4: Depress and hold the "Lock" button on your remote for one full minute. This allows the remote and the control module to communicate and sync. Release the "Lock" button and turn the memory switch in the control module back to the "Off" position.
(Kleophaus Livingston/Demand Media) Step 5: Turn the ignition switch to the "Off" position and test the remote by pressing the "Lock" or "Unlock" button, verifying that the doors do lock or unlock.


Read more : http://www.ehow.com/how_6362326_program-entry-remotes-hyundai-sonata.html

The transmission range switch that detects the shift lever position (N or P) could be short circuited. Replace the switch or correct the wirings.

Can you shift out of park if you don't start the engine ?
Often times the brake light switch is faulty or the solenoid that locks the shifter. Sometimes the shifter can be moved if the key lock is turned but not to the on position.

I need one new hazard switch for my hyunday sonata 1998 4cilinder

Hi

Make sure all door switches are functioning properly. See that each switch pushes in and out, without sticking.

Sounds like switch.

The brake light switch should be on the brake pedal near the top. Look for a circular item or box with 2 or 4 wires coming out of it at the top end of the brake pedal.

That particular switch is on the dome light itself. It'll have three settings, Off, On, and Dome. Just like it says, the Off position makes sure the dome light never comes on, the On position makes sure the dome light is always on and the Dome position makes sure the dome light comes on when you open the door.

in order to replace fuel pump one has to drop the gas tank.. make sure car is turned off unplug all hoses and electrical switches, once the gas tank is off the car the fuel pump is visible on the top side of the tank... simply replace the old pump with the new one.... place gas tank back in place plug all hoses and switches back..turn car on and leave it on idle for a couple of min..

car should be under warranty .. try having a new key made .if that dosent fix it. it's in the key lock maybe a wire loose .