What are the tools I need to change my starter on a 2006 Nissan Altima

SOURCE: How do I remove a starter off a 1998 nissan Altima?

need an engine size

SOURCE: change the fuel filter of my nissan altima 2006

the fuel filter is part of the fuel pump assembly.you can remove fuel pump by removing the rear seat bottom.you dont have to drop gas tank.

ZJ Limited

• 17989 Answers
• Posted on Nov 27, 2009

SOURCE: Howm do I replace a starter on a 1995 Nissan

Nissan 240SX/Altima 1993-1998 Repair Guide

Altima
(see Figures 1, 2 and 3)



Fig. 1: The starter is located to the left of the oil filter housing on the engine block



Fig. 2: The starter motor is removed from the bottom side of the engine compartment



Fig. 3: When installing, be sure to align the starter's mounting bolt holes with those in the engine block

1. Disconnect the negative battery cable.
2. Raise and support the vehicle safely.
3. Remove the starter support bracket, as required.
4. Label and disconnect the starter electrical harness.
5. Support the starter from beneath the vehicle using a jackstand.
6. Remove the starter mounting bolts.
7. Carefully lower the starter from the vehicle.

1. Position the starter on the engine and support it using a jackstand.
2. Install the starter mounting bolts and tighten to 30-37 ft. lbs. (40-50 Nm).
3. Connect the starter electrical harness.
4. Install the starter support bracket, as required.
5. Lower the vehicle.
6. Connect the negative battery cable.

ZJ Limited

• 17989 Answers
• Posted on Apr 05, 2010

SOURCE: How do you remove a 1999 Nissan Altima starter?

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

1. Remove or disconnect the following:
   Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle



Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle



Fig. Starter location and mounting detail-3.5L Maxima

1. Install or connect the following:
   Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable
   

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
   

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle
   
   
   Fig. Starter location and mounting detail-3.5L engine
   

SOURCE: MY NISSAN ALTIMA 2006 2.5

did you check the sensors and if you are getting fuel and spark