Question about 1996 Toyota Camry

Open Question

How to remove the quarter glass from a 2 door 1996 toyota camry

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Toyota Ed

  • 1861 Answers

SOURCE: INSTALL SIDE VIEW MIRROR ON A 1997 TOYOTA CAMRY

Yes, you have to remove the door panel.

Remove the 2 plastic protectors on the front edge, and remove the 2 brass colored screws. Next, remove the push pins from the latch side. Push in, and pull out the whole thing. Next, under the armrest, remove the screw. Lift up the power windoe control, being careful to not break the plastic retainer tab. Remove the screw under the window control. Starting at the bottom, pull out the panel, and, when all of the clips are loose, pull the panel straight up. It is best to do this with the door panel as warm as possible, like in a heated garage. Doing this outside in the cold will break all of the plastic retainer clips; they are quite brittle whn cold.

I hope this helps

Thanks for choosing FIxYa for assistance. A FIxYa rating (4 blue diamonds) would be greatly appreciated.

Posted on Feb 23, 2009

Ad

Anonymous

  • 2 Answers

SOURCE: To remove the interior door panel of a 1996 Toyota camry so that

My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
Timmy P.

Posted on Mar 04, 2009

Anonymous

  • 255 Answers

SOURCE: How do you remove rear brake dust covers 1996 Toyota Camry

there are plastic covers directly on top of you lug nuts remove with four way or socket clockwise direction these plastic caps will screw off releasing wheel cover. then remove lugs.

hope2help shack

Posted on Apr 17, 2009

Chris Yelton

  • 708 Answers

SOURCE: 2001 Toyota Camry - Removing driver interior door panel

you can take a screw driver and pry it off. Be careful if you have power windows, if it falls right off then it could pull the wires loose. The panels have clips that clip to the door. Therefore, the only way to get the panel off is to pry it off.

Posted on Mar 07, 2010

Anonymous

  • 36 Answers

SOURCE: firing order for toyota camry v6 1996

the firing order is in fact 1 2 3 4 5 6 the number one cylynder is on the left at the back, as you look at the engine from the front >>
positions of cylinders
-------------
1 3 5

2 4 6
------------

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

Tip

How To Fix Replace 2.2L Engine Air Intake Hose Toyota Camry 1996


How To Fix Replace 2.2L Engine Air Intake Hose Toyota Camry 1996

on Apr 26, 2012 | 1996 Toyota Camry

Tip

How To Replace Broken Rear Quarter Glass Toyota 4 Runner 1996-02 1AAuto.com...


How To Replace Broken Rear Quarter Glass Toyota 4 Runner 1996-02 1AAuto.com


on Mar 20, 2012 | 2002 Toyota 4Runner

2 Answers

The. Glass seems to Be loose in the door of a 2000 Camry convertible


you will have to remove door panel to inspect the lower glass mounting frame to see if the rollers on window regulator frame are bad or lower glass mounting frame could be loose,or possible window regulator motor loose or motor woren out. hope this is helpful.

Mar 22, 2015 | 2000 Toyota Camry

1 Answer

1986 toyota camry side door window came off its track and it's not power windows


it came off track for reason, something broke or rusted out, u will need to remove door panel and inspect areas where glass sits in bottom frame and where glass is attached to wind up arms

Mar 31, 2011 | 1986 Toyota Camry

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.


If you need further help, I’m available over the phone at https://www.6ya.com/expert/flavio_517b938f50183b92

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

To remove the interior door panel of a 1996 Toyota camry so that


My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
Timmy P.

Feb 21, 2009 | 1996 Toyota Camry

1 Answer

'88 toyota camry rear window stuck in down position


To get to the Window:

Remove Door Inside Handle:
remove screw, slide the handle forward.
Disconnect the control link and remove the handle.

Remove Door Trim with Inner WeatherStrip:
Remove the two screws from the armrest.
Insert a screwdriver between the trim retainers and the door panel to pry it loose.  Eight hidden fasteners. 1 top left side of door.
1 right side about same height as top of armrest. 1 (each side) about same height as bottom of armrest. 1 on each corner bottom. 1 bottom in middle.  1 on left side between bottom corner and the previous at about lower armrest height...

Remove Service Hole cover.
Remove Door Glass Run.

Remove Division Bar (upper window section divider):
Remove the two screws under the weatherstrip
Remove the bolt.
Pull out the division bar.

Remove the Window Glass:
Place the glass in the door cavity.
Remove the two glass channel mounting bolts.
Remove the window glass by pulling it upwards.

You now have access to the Power Window Regulator; possible replacement of motor etc.

What type of 'things' have you tried for fixing the window and restoring operation?

Jan 22, 2009 | 1988 Toyota Camry

1 Answer

Toyota 1997 camry door locked cannot open


I had a similar situation. It is due to malfunction of you door assembly. You need to replace it. It is hard to remove the door panel with door locked. I was able to manage it some how by removing pretty much all screws except for the 2 at the fornt side, beside the dash board. But in another instance with my friend I was able to help with a metal hanger. Slide the metal hanger beside to dood glass and try to lift the lach manually to unlock the door right from the door assembly. It worked and then we replace assembly for his car too.

Jul 04, 2008 | 1995 Toyota Camry

Not finding what you are looking for?
1996 Toyota Camry Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...