Son has 2005 Kia amanti he took to2 different shops about rear wheels play. Told lateral rods by one and rear control toe link. What's the difference in the two

Kia Amanti Rims & Custom Wheels - CARiD.com

www.carid.com > all products > wheels & tires > custom wheels > Kia

Set your Kia Amanti on the finest chrome rims. Our inventory is the top-notch selection of custom wheels and tires for Kia Amanti from most popular wheel ...

Kia Amanti - Wheel-Size.com

www.wheel-size.com > Makes > Kia

Kia Amanti - Find out the correct alloy wheel fitment, PCD, offset and such specs as bolt pattern, thread size(THD), center bore(CB) for all model years of Kia Amanti. Choose a model year to ... 2009 2008 2007 2006 2005 2004 · Kia Amanti l ... Wheel General Info The ranges of possible values for tires and rims of Kia Amanti ...

Buy Wheels and Rims Online for your 2005 KIA AMANTI ...

www.performanceplustire.com > Wheels > KIA > AMANTI

Buy Wheels and Rims Online for your 2005 KIA AMANTI and other custom wheels andrims from PerformancePlusTire.com. PerformancePlusTire.com is one of ..

It's called a control arm. Sway bar is definitely not one of the names. The other two could be, but for different manufactures. And the parts look different. But have the same funtion.

replace anything that was bent and then have the rear end alignment done at a wheel alignment specialist shop
any specialist shop when doing a front alignment should always check the rear first as it controls the accuracy of the front job

adjust the tie rod ends to achieve toe-in/out adjustment. Measure across the wheels at the front of the steering tyre and then measure across the tyre at the rear of the steering tyre ( same height) and see what the difference is. Adjust the tie rod ends until the front measurement is smaller than the rear by about 1/8 inch . Lock up the lock nuts on the tie rod ends.

Hi,
Yes, this is normal while in four wheel drive on pavement.
I will try and explain why.
In four wheel drive the front and rear drive axles are linked together by a chain in the transfer case and gears in both axles. This is a direct link with very little play between the front and rear axles.
When cornering a rear wheel will spin faster, or slower depending on the direction of the turn. this causes a binding in the drive line because the drive line wants all the wheels to turn at the same speed. So the wheel "skipping" going in reverse, is the drive lines way of compensating for the different speed of the wheels turning.
Never should a four wheel drive be used on dry pavement. I could cause a break in one of the drive line components. On a slippery surface , snow, mud, gravel, grass, There is enough slippage in the surface to aloow the driveline to compensate for the different speeds of tire rotation.
So do not try at highway speeds on dry pavement.
Your four wheel drive system is working just fine.
Wayne

Before making wheel alignment adjustment, perform the following checks:

1. Tires should be equal in size and runout must not be excessive. Tires and wheels should be in balance, and inflated to manufacturer's specifications.


2. Wheel bearings must be properly adjusted. Steering linkage and suspension must not have excessive looseness. Check for wear in tie rod ends and ball joints.
3. Steering gear box must not have excessive play. Check and adjust to manufacturer's specifications.
4. Vehicle must be at curb height with full fuel load and spare tire in vehicle. No extra load should be on vehicle.
5. Vehicle must be level with floor and with suspension settled. Jounce front and rear of vehicle several times and allow it to settle to normal curb height.
6. If steering wheel is not centered with front wheels in straight-ahead position, correct by shortening one tie rod adjusting sleeve and lengthening opposite sleeve equal amounts.
7. Ensure wheel lug nuts are tightened to torque specifications

Ride Height Adjustment

Before adjusting alignment, check riding height. Riding height must be checked with vehicle on level floor and tires properly inflated. Passenger and luggage compartments must be unloaded. Bounce vehicle several times, and allow suspension to settle. Visually inspect vehicle from front to rear and from side to side for signs of abnormal height.
Measure riding height. See figure. Riding height between left and right sides of vehicle should vary less than 1′ (25.4 mm). If riding height is not within specification, check suspension components and repair or replace them as necessary.
Wheel Alignment Procedures

Honda recommends using commercially available computerized 4-wheel alignment equipment. Follow equipment manufacturer instructions to obtain vehicle alignment settings. Use following procedures for necessary adjustments.
Civic Camber Adjustment
Compare camber settings with vehicle manufacturer recommendations. If camber is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck camber.
Civic Caster Adjustment
DO NOT use more than 2 shims. If more than 2 shims are required to adjust caster angle, check for bent or damaged suspension components.
Compare caster settings with vehicle manufacturer recommendations. If caster is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck caster.
Civic Toe-In Adjustment

1. Secure steering wheel in straight-ahead position. Measure front wheel toe-in. If adjustment is needed, loosen tie rod lock nuts. Turn both tie rods equally in the same direction until front wheels are in straight-ahead position and toe-in reading is correct. Tighten tie rod lock nuts. Reposition tie rod boots if twisted.
2. Ensure parking brake is released. Check rear wheel toe-in. If adjustment is needed, hold adjusting bolt on rear compensator arm and loosen lock nut. See figure. Adjust rear toe-in by sliding rear control arm until rear toe-in is correct. Install NEW lock nut, and tighten it while holding adjusting bolt.

Wheel Alignment Specifications

• Camber - Measurement in degrees.
  • Front: 0 (range -1 to 1)
  • Rear: 0.33 (range -1.33 to 0.67)
• Caster - Measurement in degrees.
  • 1.17 (range 0.17 to 2.17)
• Toe-In - Measurement in inches (mm).
  • Front: -0 (0)
  • Rear: 0.08 (2.0)
• Toe-In - Measurement in degrees.
  • Front: 0.00 (range - 0.16 to 0.16)
• Toe-Out On Turns - Measurement in degrees.
  • Inner: 41.00
  • Outer: 33.50

Torque Specifications Ft. Lbs (N.m)

• Rear Control Arm Adjusting Bolt: 48 (65)
• Spindle Nut: 136 (185)
• Tie Rod Lock Nut: 41 (55)
• Wheel Lug Nuts: 80 (108)

hope this helps you out.

To be honest with you, the best way is to get a manual like a Haynes or a Chilton for this procedure since it is so different on so many models.

was your car in a wreck since you have own it?
that would be the only way anyone could bend steering or suspension parts.if your tires are leaning out on top,
it would be a part called"lower control arm assembly",
if you stand in front of your car with the steering wheel straight,and your tires are pointing in on each side,or pointed out instead of straight,that would be a "tie rod "
there is an inner tie rod and an outer tie rod end.
you need to take your car to a shop that does alignments,and have them tell you exactly what is wrong,you can even get lower control arm assemblies
from a salvage yard.but do yourself a favor and don't take your car to a MONROE or MIDAS type shop,they are only there to sell and make commissions! Find a normal shop that the owner is the mechanic.

It's sad that the dealer cannot or will not solve this problem. Sounds like they want to keep having you spend money on pads and rotors in stead of fixing the problem. I would look for a shop that has better experience. It doesn't have to be a dealer shop to find the best people.
Well, in most cases like this, the caliber 80% to blame. 20% is the hardware ( springs and clips ). The hardware helps keep the shoes in place and helps relieve pressure/sticking when brakes are not in use.
The best solution would be to replace calibers and hardware on both sides. Doing both sides prevent from one side being stronger or weaker than the other. Therefore, one side will not wear out faster than the other.

The main cause of steering wheel off-center is toe misalignment or rear axle misalignment. Toe can fall out of adjustment fairly easily as a result of daily driving, so you can imagine the effects of pounding it through 4WD trails on a regular basis.

Toe is designed to preload the steering linkage to remove play in the system. You can visualize toe angle from above; toe-in, or positive toe, is displayed when the leading edges of the tires are closer together than in the rear. Toe-out, or negative toe, is when the leading edges are farther apart. Zero toe is when wheels are pointed straight ahead and are parallel to each other. A slight amount of positive toe is preferred for most vehicles.

Improper toe angle isn't the only reason a steering wheel won't center. This phenomenon can also be caused by the steering linkage not being centered when toe was adjusted in the first place. This can be corrected by recentering the steering wheel and readjusting toe to proper specs. A bent steering arm or linkage component can also cause the steering wheel to be off-center. I've also seen this occur due to loose steering arm bolts. An off-center steering wheel contributes to tire wear because as the wheels are turned off dead center they turn toe out and increase tire scrubbing.

Sometimes an off-center steering wheel is accompanied by a wheel pull to one direction or the other and could be the result of a damaged component somewhere in the vehicle - a bent axlehousing could be throwing off the rear toe setting (rear toe setting is often overlooked). A bent frame or overly worn suspension bushings can also be the cause. If your wheel is off-center and also pulling, it can be as simple as incorrect tire pressure from side to side. Memory steer is another effect that is usually associated with an off-center steering wheel. This is when the steering wheel returns to an off-center position and can result in steering pull or drift after completing a turn. This can be caused by binding in the steering linkage as well as power steering system issues such as leaks or improper hydraulic pressure. Steering linkage bind occurs when proper geometry is not maintained in lifted vehicles.

Many 4x4s don't have factory provisions for adjusting caster and camber and rear toe and camber, but the front toe setting is easily adjusted. Toe is controlled by the steering linkage. By loosening the adjusters on the tie rod and shortening or lengthening the tie rod by turning the ends, toe angle can be adjusted. This should not be a substitute for regular professional wheel alignment jobs and is simply a tip that can be used to put off frequent trips to the alignment shop due to regular trips to the trail.
------------------------------------------------------------------------------------------------
Before determining toe angle and/or performing adjustments, it's a good idea to start the engine and turn the steering wheel side to side to relieve pressure in the system. Then, turn the wheels straight and shut off the engine. You should also roll the vehicle back and forth a few times between measurements.

Get someone to hold the other end of the measuring tape and measure the leading toe distance. This is the distance between the leading edges of the front tires. You'll compare the results to the distance between the trailing edges of the tires directly opposite from where you took the first measurement.

The higher number will indicate toe direction: higher number in leading edge indicates toe out; higher number at trailing edge displays toe in. Larger-than-stock tires require more positive toe for best results.

Once the necessary measurements are performed to determine what the current toe setting is, you can loosen the bolts on the tie-rod adjuster sleeve so that the tie-rod ends can be rotated. Don't forgot to tighten the adjusters when you're done as damage or injury could result.

The tie-rod ends thread into the tie rod. The ends can be threaded in or out of the tie rod to make the assembly longer or shorter. Longer creates more toe out; shorter toe in. Don't make huge adjustments all at once. It's best to adjust and measure a few times to achieve appropriate setting.
--------------------------------------------------------------------------------------------------
I hope this helps you if you were looking to do a toe alignment yourself if you have decent knowledge of component location on a jeep.