Re: How do I reset the low kefob battery on the DIC of a...
Had the same problem with my 2004 Tahoe. I turned the ignition to the run position (don't crank motor), when the warning came on I held the unlock button on the key fob until the warning was removed. I took out the key, locked then unlocked the door. When I put the key in the ignition, the warning doesn't come on anymore. Hope this helps.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Turn the key on. Look at the security light or DIC. If t he light stays on(after a couple seconds) or DIC displays security. The reset for it is.. Turn the key on for ten minutes, off for thirty seconds. Try to start. The relearn is three times this, try to start after the third time. Have a battery charger on it. Battery goes low or you accidentally hit the starter, you have to start all over. If the light goes off, it's not security. Have the codes read. If you want to throw more money at it. replace the crank sensor. This may be the reason for no spark.
make sure you have power and ground at the ipc connector, if you do, cluster needs to be replaced. If you don't have power and ground, start looking for open wires.
For vehicle with steering wheel conrtols ,to reset the fuel,Press and hold the select button for five seconds while the fuel filter life message is displayed . The message will appear on the DIC for ten second For vehicle without steering wheel control ,do the following, without pressing the pedals,turn the ignition key to the on position without starting the engine ,wait five seconds,completely press the the brake and the accelerator pedal simutaneously, and hold for ten seconds ,the system is now reset , The next time the engine is started the message will no longer be displayed, Always reset after a fuel filter change
oh thats the change oil light expect it every 3500 to 4500 miles they glow.. you can usually reset it by holding down the trip button with the car off and then turn the key to the II position where everything lights up
so read me >>>>> Buick Rainier 2004-06, Buick Rendezvous 2002-05 w/o (DIC) Driver Information Center
Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three time in five seconds. If the CHANGE OIL SOON’ indicator flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHANGE OIL SOON indicator comes on and stays on for five seconds, repeat the procedure. Buick Rainier 2004-05 wI (DIC) Driver Information Center
The DIC display is located on the instrument panel cluster above the steering wheel. The DIG buttons are located on the steering wheel. Press button with the gas pump symbol to display engine oil life. Press button with the arrow symbol to reset engine oil life display. Buick Rendezvous 2002-06 wI (DIC) Driver Information Center
To reset Service Reminder Indicator, turn ignition on with engine not running. Press the MODE button until DIC reads oil life left hold SET to reset. Press and hold the SET button until 100% is displayed. You will hear three chimes and the change oil message will go out. If the CHANGE ENGINE OIL’ message comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure.
Have you driven the vehicle over 45 mph.? If not, drive 5 miles above 45mph and the light will reset. You can also clear clear pressure reading by reseting through the DIC, mode and set buttons. Owners manual will explain use of the DIC ( Driver Information Center) Good luck, let me know. Regards,
I have a 2004 Silverado with the same problem.
After scrollng the internet for months and reading every manual I could get my hands on, I found, for me, a quick and easy way. Open the hood, remove the cover to the Underhood Fuse Block on the drivers side of the vehicle near the battery.
If you have the manual for your truck, go to page 5-126 and locate the fuse that says IPC/DIC, it is a 10 amp fuse.
Pull the fuse and start your truck or a few sceonds.
You will notice that nothing on your insterment will work.
Turn engine off and replace fuse.
After I did this, the message did not come back, and started my truck about 15 times to make sure.
It worked for me....good luck to you.
PLease clarify what is going on here.
×