- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You don't need a part number, you just buy by 'year make model'. Don't go cheap on sensors, make sure they are Denso OEM quality and not made in China or Mexico.
P0017 timing chain Chevy Colorado P0017 Case Study Part 1
155,000 miles This is not a DTC for the crank sensor . This is for variable valve timing .
DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1
The camshaft position (CMP) actuator system enables the engine control module (ECM) to change the timing of the camshafts while the engine is operating. The CMP actuator solenoid signal from the ECM is pulse width modulated (PWM). The ECM controls the CMP actuator solenoid duty cycle by controlling the amount of solenoid ON time. The CMP actuator solenoid controls the advance or the retard of each camshaft. The CMP actuator solenoid controls the oil flow that applies the pressure to advance or retard the camshafts.
Ignition voltage is supplied directly to the CMP actuator solenoid. The ECM controls the solenoid by grounding the control circuit with a solid state device called a driver. The ECM compares the camshaft position or the camshaft angle, to the position of the crankshaft.
Your a little out of your league on this ! Your best bet ,take it to a qualified repair shop !
• Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, camshaft actuator, camshaft sensor, crankshaft sensor, or timing chain can cause this DTC to set.
• An actuator that is in the full advance or retard position can cause this DTC to set.
• The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).
• Observing the desired and actual camshaft angle parameters, with a scan tool before a DTC sets, may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.
Which engine ? This vehicle had option of six different engines , 2.4 , 3.5 , 2.8 , 3.0 , 3.2 , 3.6 And are you picking on the right part ? What code >
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit
DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit
It may not even be a cam sensor problem ! DTC P0340: Intake CMP Sensor Circuit
DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance
DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance
Camshaft Position (CMP) Actuator System
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the Park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the Park position, and the locking pin retains the CMP actuator sprocket to the camshaft
Sep 8, 2007 - 11 posts - 8 authors
On my Trailblazer I have a code P0014 . this says Camshaft Position Actuator B ... If the desired and actual cam phase angle error exceeds its ... This diagnostic procedure supports the following DTC: ... replace the camshaft actuator solenoid, change the engine oil and filter, ... 2004 Chevy TrailBlazer LT
P0014 - Camshaft Position Actuator Solenoid "Relearn"
11 posts
Dec 11, 2009 cam crank sensor mismatch
11 posts
Jul 4, 2009 More results from forums.trailvoy.com
Dec 31, 2007 - 14 posts - 6 authors
Tech Code "dtc P0014" 2003 Trailblazer - posted in Chevy ... it had been serviced before for the same thing in 2003 or 2004! ... replace the camshaft actuator solenoid, change the engine oil and .... The extended war. co. prob. would not be to happy since they already fixed the sensor once or twice already.
the range switch on the trans maybe bad. its usually right twhere the linkage attaches from the shifter to the trans. But I would recommend a garage that does FORD work to ck it for you. You could guess and replace a lot of uneeded parts.
×