1992 Buick Century Logo

Related Topics:

a
angela gisela Posted on Nov 05, 2016

Remove driver side door panel 1992 buick century

Replacing left side mirror

5 Related Answers

Anonymous

  • 316 Answers
  • Posted on May 25, 2009

SOURCE: How do I remove the front door panel to replace the mirror

Normal 0 Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.

If you don't have power windows you will have to remove the manual window crank. It is held in place by a clip on the back side of the base. To remove the clip, you will need a small hook (kind of like a knitting needle). Put the hook in behind the base, and grab the clip and pull it off. To replace it, slide the clip back on the window crank, and snap it back on the door.

Ad

Anonymous

  • 1 Answer
  • Posted on Jul 19, 2009

SOURCE: I need to replace the 99 buick century side mirror

There is a small plastic piece (triangular shape) at the top of the door panel, opposite of the mirror. It is held in place by a plastic clip. You can gently pop that out, with a flat blade screwdriver or something similar. That will expose 3 bolts with nuts on them. On my 2000 Century, they are 10 mm. Take off those three nuts, and the mirror will come off.

Anonymous

  • 1986 Answers
  • Posted on Aug 14, 2009

SOURCE: 99 Buick LeSabre, how do I remove driver side door panel to replace power window motor?

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Anonymous

  • 1986 Answers
  • Posted on Sep 29, 2009

SOURCE: How do I replace broken 2002 buick century passenger side mirror?

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Anonymous

  • 1986 Answers
  • Posted on Sep 29, 2009

SOURCE: replace left side rear view mirror/2005 buick century

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

How to replace driver's side mirror 1995 Roadmaster

You have to take the door panel off , I'll send this youtube link. It isn't the same car but there all pretty much the same ! How To Install Replace Broken Damaged Mirror 1992 99 Buick Lesabre
tip

Power Mirror Wiring Schematic 92 Buick Lesabre 1992 thru 1997 & More

Here is a schematic which my dad & I devised over the course of two hours for the power mirror wiring on our 1992 lesabre, as we couldn't find any wiring info to handle this issue.

http://www.iqmetals.com/else/lesabre/

That's our/my website, and that folder will let you see & get all of the pictures & diagrams

The wiring harness for the power mirror switch was acquired through Rock Auto, and the wire lettering scheme was embossed onto the plastic.
Here's a written breakout of the wires & their locations/purposes.

A= Ground
B= Common Left/Right Motion(Splits to both sides)
C= Common Up/Down Motion(Splits to both sides)
D= Left Side - Left/Right Motion
E= Left Side - Up/Down Motion
F= Right Side - Up/Down Motion
G= Right Side - Left/Right Motion
H= Positive 12V

Now Assuming that all of the power mirrors are wired & color coordinated the same, that would connect....
B -- Light Blue wire of Both Mirrors
C -- Green wire of Both Mirrors
D -- Gray wire of Drivers Side Mirror
E -- Dark Blue wire of Drivers Side Mirror
F -- Dark Blue wire of Passengers Side Mirror
G -- Gray wire of Passengers Side Mirror

In our circumstance we hooked up the power and ground inline with the power window Power(Pink) & Ground(Black) wires which are nearby in the door. The fuse/circuit should easily handle the minor load of power mirrors, even if you were using the windows and mirrors at the very same time... a rarity I do suppose.

647aa8a.jpg
77801ab.jpg
3e90b3f.jpg
f8d21d5.jpg
on Nov 28, 2009 • 1992 Buick LeSabre
0helpful
1answer

1996 buick century side mirror unconnected. how do i put the nuts back on?

Should be a small trim panel at the top of the door panel that comes off.
Usually triangle shaped.
0helpful
1answer
0helpful
1answer

I've got a broken driver side rear view mirror on a 1990 Buick Century. I've got the replacement mirror, I just need help getting the old mirror off the door. Suggestions?

This is what you do take the door skin off of the inside of the door and at the top corner there will be i think three nuts and than your going to need door clips after your done in order to put the door panal back on
5helpful
1answer

I need to replace the 99 buick century side mirror

There is a small plastic piece (triangular shape) at the top of the door panel, opposite of the mirror. It is held in place by a plastic clip. You can gently pop that out, with a flat blade screwdriver or something similar. That will expose 3 bolts with nuts on them. On my 2000 Century, they are 10 mm. Take off those three nuts, and the mirror will come off.
0helpful
2answers

I have a 1992 buick century custom. The end of the door opener handle inside on the drivers side just broke off so the door will not open from the inside. I can see what needs replacing. I cant see how to...

There is a " C " clip attached to the window handle, which secures it to the mount. . A special claip removing tool is required . Hope this helps.
0helpful
1answer

Replace rear view mirror/driver side

Necessary to remove L/F door trim, remove (2) nuts holding mirror to door (Cover entire mirror to protect door sheetmetal ) disconnect electrical connector and remove mirror from door, reverse procedure to reinstall. Hope this helps
5helpful
1answer

Replace left side rear view mirror/2005 buick century

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
11helpful
2answers

How do I replace broken 2002 buick century passenger side mirror?

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
Not finding what you are looking for?

736 views

Ask a Question

Usually answered in minutes!

Top Buick Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...