DISABLING SERVICE RIDE CONTROL via REPROGRAMMED BCM
Anyone have the part # for a 2002 Denali AWD?
SCM - (Suspension Control Module) BCM - (Body Control Module)
I too want to recode the BCM (where the heck is it located) so that the SERVICE RIDE CONTROL error code is disabled.
Anyone have a good source for an individual who can reprogram here in the US?
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
What kind of scan tool ? Will it scan all the modules on the vehicle or is it just OBD2 type ? Did you check wiring diagrams an test electrical circuits for air ride an test with a DVOM - digital volt ohmmeter ? Do you know how to test ALC relay circuits . You replaced a bunch of parts that probably were not needed (,air ride compressor, fuses and ALC relay and the compressor still won't work ) ?
Which of these does your vehicle have
Automatic Level Control
Electronic Suspension Control (ESC)
The vehicles rear leveling compressor motor is switched on and off via a compressor motor relay which is controlled by the suspension control module. The suspension control module provides a switched path to ground whenever compressor activity is required. The suspension control module continually monitors the compressor motor relay circuitry to determine if the voltage level agrees with the commanded state.
DTC C0655 Level Control Compressor Circuit
DTC C0660 Level Control Exhaust Valve Circuit
The exhaust solenoid valve is switched on and off via the suspension control module. The suspension control module provides a switched path to ground whenever exhaust activity is required and during a compressor "head-relief" sequence which occurs at compressor start-up if system pressure is lower than 68.95 kPa (10 psi). The suspension control module continually monitors the exhaust solenoid valve circuitry to determine if the voltage level agrees with the commanded state.
DTC C0711 Level Control Air Pressure Sensor Circuit
Circuit Description
The suspension control module uses a 5-volt analog air pressure sensor to determine the amount of air pressure in the automatic level control (ALC ) system. The valid signal voltage range of the sensor is 0.15-4.85 volts. The sensor signal voltage will increase and decrease within the valid voltage range as system pressure increases and decreases.
Your best bet ,take it to a qualified repair shop that knows what they are doing .
Anti-theft system is software programmed into the vehicle modules (computers) PCM/ECM - engine computer , BCM - body control module. Your best bet , take it to a qualified repair shop.
Passlock™ System
The theft deterrent system has been incorporated into the body control module (BCM). The theft deterrent is provided in order to prevent the vehicle operation if the correct key is not used in order to start the vehicle. The ignition key turns the lock cylinder. The cylinder rotation produces an analog voltage code in the Passlock™ sensor. This voltage code is received by the BCM. The BCM compares the voltage code to the previously learned voltage code. If the codes match, a class 2 message is sent from the BCM to the powertrain control module (PCM)/vehicle control module (VCM). The message enables the fuel injectors.
The design of the Passlock™ system is to prevent vehicle theft by disabling the engine unless the ignition lock cylinder rotates properly by engaging the correct ignition key. The system is similar in concept to the PASS-Key® system. However, the Passlock™ system eliminates the need for a key mounted resistor pellet. The components of the Passlock™ system are as follows:
• The ignition lock cylinder
• The ignition switch
• The Passlock™ sensor
• The Body control module (BCM)
• The security telltale
• The vehicle/powertrain control module (VCM/PCM)
Would need to know what DTC'S - diagnostic trouble codes are stored in the module for the autoride suspension . Hooking up a professional type scan tool ,looking at input data to the module etc... Looking at a wiring diagram an testing electrical circuit's using a DMM - digital multi-meter . Reading how the system works ,what all involved in making the system work . This is how a professional Tech would go about diagnosing this .
The automatic level control (ALC) system maintains a desired rear suspension position under all types of towing, hauling and loading conditions. The following components are involved in the operation of the ALC system:
• Air line tubing--Pressurized air from the ALC compressor is pumped to each of the rear shocks via air line tubing.
• Air drier--Pressurized air from the compressor is run through a drier containing a moisture absorbing chemical preventing water accumulation in the rear shocks.
• Compressor--Supplies pressurized air to the rear shocks
• Compressor motor relay--The relay supplies battery positive voltage to the ALC compressor motor.
• Pressure sensor--The electronic suspension control module (ESCM) module provides a 5-volt reference and low reference to the ALC pressure sensor. The module receives the signal voltage that is relative to the air pressure applied to the rear shocks.
• ESCM--Controls the ALC system and electronic suspension control (ESC) system and detects failures in both. The module monitors inputs from the position sensors, and pressure sensor to determine when to raise and lower the vehicle to trim height as the vehicle is loaded or unloaded. The module limits pump activation to 255 seconds to prevent thermal damage.
• Exhaust valve--An electric solenoid activated by the ESCM to vent air pressure from the rear shocks.
• Left and right rear suspension position sensors--The module provides a 5-volt reference and low reference to all 4 of the body-to-wheel suspension position sensors. The sensors send the ESCM a signal voltage that is relative to the rear suspension ride height
• Left and right rear shock absorbers with internal air chambers and dampers--Dampens the rear suspension and maintains trim height depending on the air pressure applied.
Is there a computer related code which I must enter via the radio ??? You don't enter anything through the radio !!!!! Having factory service repair info so you can read how the anti-theft system works an a scan tool to pull DTC'S - diagnostic trouble codes is the proper way to diagnose .
The theft deterrent system has been incorporated into the body control module (BCM). The theft deterrent is provided in order to prevent the vehicle operation if the correct key is not used in order to start the vehicle. The ignition key turns the lock cylinder. The cylinder rotation produces an analog voltage code in the Passlock™ sensor. This voltage code is received by the BCM. The BCM compares the voltage code to the previously learned voltage code. If the codes match, a class 2 message is sent from the BCM to the powertrain control module (PCM)/vehicle control module (VCM). The message enables the fuel injectors.
The design of the Passlock™ system is to prevent vehicle theft by disabling the engine unless the ignition lock cylinder rotates properly by engaging the correct ignition key. The system is similar in concept to the PASS-Key® system. However, the Passlock™ system eliminates the need for a key mounted resistor pellet. The components of the Passlock™ system are as follows:
• The ignition lock cylinder
• The ignition switch
• The Passlock™ sensor
• The Body control module (BCM)
• The security telltale
• The vehicle/powertrain control module (VCM/PCM)
Your best bet , take it to a qualified repair shop.
Hi Jose: The first place to start is to have Ride Control Module scanned for trouble codes, this requires a high end scan tool. Most common problem is the air compressor in the rear or a height sensor. Here is how the system works.
Automatic Level Control Description and Operation The RTD system is bi-state real time damping system. The Suspension Control module controls the suspension damper solenoids and suspension position sensors, along with parts of the automatic level control (ALC) system and electronic variable orifice (EVO) power steering system.
The Automatic Level Control system consists of the following: • Suspension Control Module • Compressor/Leveling Module - Air Pressure Sensor - Exhaust Solenoid • Compressor Motor Relay
The objective of the Automatic Level Control System is to provide constant ride height at all load conditions. The Suspension Control module monitors body-to-wheel height, and vehicle speed.
The Suspension Control module will use the rear body-to-wheel displacements and vehicle speed inputs to keep the rear trim height of the vehicle at its desired level.
The electronic suspension control (ESC) system is bi-state real time damping system. The ESC module controls the suspension damper solenoids and suspension position sensors, along with parts of the automatic level control (ALC) system, if 1500 series.
The ESC system consists of the following: • The ESC module • The compressor/leveling module, if 1500 series - The air pressure sensor, if 1500 series - The exhaust solenoid, if 1500 series • The compressor motor relay, if 1500 series • The steering handwheel speed/position sensor • The suspension damper solenoids • The suspension position sensors
Hope this helps; also keep in mind that your feedback is important and I'll appreciate
your time and consideration if you leave some testimonial comment about
this answer.
What color wire's ? There is a relay which is controlled by the ESC module (computer ) Electronic suspension control module . The relay supply's B+ power to the compressor . Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. Year , make , model and engine size. Under system click on suspension then under subsystem suspension controls will pop up on it's own . Click the search button then the blue link's . System can set DTC'S - diagnostic trouble code's . Has hight sensors , control module ,relay etc.....
this means that you have a fault with your stability control system. the stability control is designed to prevent a rollover it detects body roll when you are driving the ride control is the air suspension sytem this keeps ride hieght the same based on how wieght is in the vehicle. check the links that connect the switches to the suspension you may have one dissconnected (these links wear out over time you night have to replace them) there is one on each wheel postion if you need anything else let me know
A ton of things could be wrong with your autoride system. If you have more than about 70k miles and haven't replaced the rear shocks ($500+ EACH!!! at the dealer), then they are probably leaking out. If they leak out, then the air compressor will always run. Eventually the air compressor/ride level sensor module (located on the driver side rear wheel on the inboard side of the frame, $300+ at the dealer) burns out because it's not designed to run at 100% duty cycles. After the air compressor burns out, the Electronic Stability Control module (in an XL, located inside the passenger side rear wheelwell trim, next to the third row seat, $300+ at the dealer) will probably short out. If your autoride isn't working and you don't get a "Service Stability" message, your ESC module is probably going bad.
It is possible to convert to regular shocks, but to keep the Stability Control (still has to control your brakes and front variable dampening shocks during "evasive" maneuvers), you have to insert some 1/4 watt resistors in to the ride height sensor connectors (can't remember what values, but I'm sure you can Google that) so that the Stability system doesn't throw a code. Not that it matters, but the message can get annoying if it's always there to nag...
My dealer quoted over $2500 to replace the entire system. I figure I can find the control modules from my local junkyard for $300, and the shocks from ebay for $350 for the pair. Be sure to match all of the GM part numbers, and keep an eye out for an upgraded Air Compressor module - GM released an update that is heavier duty and more water-resistant than the first design. I don't remember the part number, but my dealer included the upgrade with my quote.
Oh, and the only "easy" way to test the modules is with a Tech 2 tool. Otherwise it's lots of testing with a 12-volt source and a couple of multimeters and oscilliscopes...
where is body control module located
reset body control module
×