I have code b1025 on mercedes c240 2001 airbag ignition circuit 1 driver side resistance to high

Speculation without further details but 3 usual causes:
1. Clock spring in steering wheel for airbag open circuit.
To Test - disconnect battery-disconnect airbag ribbon from steering wheel -insert 3 -8ohm resistance bypass in airbag plug below steering column feeding clockspring. reconnect battery and see if light goes out after 5 seconds
2. Check passenger seat sensor operational.
To test - with ignition off - disconnect plug under passenger seat for sensor pad and insert test ohm resistance in feed plug. switch ignition on as test 1.
3. Check steering wheel button operation. if any radio actions do not work problem may be infrared link between steering wheel and radio (especially aftermarket modules)

Codes 32 to 35

These codes are signaled by three flashes, a two-second pause and the number of flashes that corresponds to the second digit. Code 32 (triple flash, pause, two flashes) means the driver side airbag has a circuit open or with high resistance, Code 33 (triple flash, pause, two flashes) means the passenger side airbag has a circuit open or with high resistance, Code 34 (triple flash, pause, four flashes) means the driver side airbag has a shorted circuit or one with low resistance and Code 35 (triple flash, pause, five flashes) means the passenger side airbag has a shorted circuit or one with low resistance.

I personally would let some one who knows what they are doing look at it. Grounding or feeding the wrong wire could set off an air bag and hurt someone.

Lamp Fault Code 36 has four possibilites, of which are the following:
-Driver Side Air Bag Circuit Shorted to Ground
-Driver Side Air Bag Circuit Shorted to Battery or Ignition
-Driver Side Air Bag Circuit Resistance High
-Driver Side Air Bag Circuit Resistance Low
With that said, it's most likely your driver air bag needs to be replaced...

list of airbag flash codes.

12=Low Battery Voltage
13=Air Bag Circuit Shorted to Ground
14=Primary Crash Sensor Circuit Shorted to Ground
21=Safing Sensor Not Mounted to Vehicle Properly
22=Safing Sensor Output Shorted to Battery Voltage
23=Safing Sensor Circuit Input Feed/Return Circuit Open
24=Safing Sensor Output Feed/Return Circuit Open
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34=Driver Side Air Bag Circuit Low Resistance or Shorted
35=Passenger Side Air Bag Circuit Low Resistance or Shorted
41=RH Primary Crash Sensor Feed/Return Circuit Open
42=LH Primary Crash Sensor Feed/Return Circuit Open
44=RH Primary Crash Sensor Not Mounted to Vehicle Properly
45=LH Primary Crash Sensor Not Mounted to Vehicle Properly
51=Air Bag Diagnostic Monitor Internal Thermal FuseFuse Blown Due to Intermittent Short to Ground
52=Backup Power SupplyVoltage Boost Fault
53=Primary Crash Sensor Circuits Resistance to Ground or Air Bag Diagnostic Fault

list of airbag flash codes.

12=Low Battery Voltage
13=Air Bag Circuit Shorted to Ground
14=Primary Crash Sensor Circuit Shorted to Ground
21=Safing Sensor Not Mounted to Vehicle Properly
22=Safing Sensor Output Shorted to Battery Voltage
23=Safing Sensor Circuit Input Feed/Return Circuit Open
24=Safing Sensor Output Feed/Return Circuit Open
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34=Driver Side Air Bag Circuit Low Resistance or Shorted
35=Passenger Side Air Bag Circuit Low Resistance or Shorted
41=RH Primary Crash Sensor Feed/Return Circuit Open
42=LH Primary Crash Sensor Feed/Return Circuit Open
44=RH Primary Crash Sensor Not Mounted to Vehicle Properly
45=LH Primary Crash Sensor Not Mounted to Vehicle Properly
51=Air Bag Diagnostic Monitor Internal Thermal FuseFuse Blown Due to Intermittent Short to Ground
52=Backup Power SupplyVoltage Boost Fault
53=Primary Crash Sensor Circuits Resistance to Ground or Air Bag Diagnostic Fault

Ford Airbag Fault Codes
Flash Code Component/Fault Description
- No Air Bag Indicator - Inoperative Indicator Circuit
- Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor
Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 Right Radiator Primary Crash Sensor Feed/Return Circuit Open
42 Left Radiator Primary Crash Sensor Feed/Return Circuit Open
44 Right Radiator Crash Sensor Not Mounted to Vehicle Properly
45 Left Radiator Crash Sensor Not Mounted to Vehicle Properly
51 Airbag diagnostic Monitor Internal thermal fuse Blown
52 Back-up Power supply Voltage Boost Fault
53 Front Crash Sensor High Resistance or Diagnostic Monitor Failure

How do i remove t-mobile content lock with out credit card or by going to t-mobile shop.

Hi there:The Restraints Control Module (RCM / located behind right side of the instrument panel) monitors the resistance of the driver side air bag circuit loop and the air bag module igniter at RCM, if the resistance is greater than 3.6 ohms, the RCM will store diagnostic trouble code B1994 and flash lamp fault code.
About the possible causes, pay attention that a high resistance on the driver side air bag circuit can be caused by:

• - damaged wiring on circuit 1257 (WH/LB).
• - damaged wiring on circuit 1258 (BN/LB)
• - damaged driver side air bag module.
• - damaged RCM.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

This is a code 46 LH Crash Sensor - Not Mounted to Vehicle Properly. Often there is a poor contact on one of the wiring connectors. Some of the problems can happen from a poor connection where everything connects under the drivers side seat.
Here is a list of codes for the airbag light issues.

Air Bag Fault Code Table

AIR BAG DIAGNOSTIC MONITOR FAULT CODE PRIORITY TABLE

Priority Code Component/Fault Description

Highest -- No Air Bag Lamp - Inoperative Lamp Circuit or No Ignition Voltage to Diagnostic Monitor

' -- Continuous Air Bag Lamp - Diagnostic Monitor Disconnected or Inoperative

' 12 Low Battery Voltage

' 13 Air Bag Circuit or Crash Sensor Circuit - Shorted to Ground

' 21 Safing Sensor - Not Mounted on Vehicle Properly

' 22 Safing Sensor Output Circuit - Shorted to Battery Voltage

' 23 Safing Sensor Input Feed/Return Circuit Open

' 24 Open in Circuit 944B or Low Resistance in Crash Sensor(s)

' 32 Driver Side Air Bag/Safing Sensor Circuit - High Resistance or Open

' 33 Pin 7 Not Grounded at Diagnostic Monitor

' 34 Driver Side Air Bag/Safing Sensor Circuit - Low Resistance or Shorted

' 35 Low Resistance Across Pins 8 and 9 at Diagnostic Monitor

' 41 Crash Sensor Circuit - High Resistance or Open

' 44 RH Crash Sensor - Not Mounted to Vehicle Properly

' 45 Center Radiator Crash Sensor - Not Mounted to Vehicle Properly

' 46 LH Crash Sensor - Not Mounted to Vehicle Properly

' 51 Diagnostic Monitor Internal Thermal Fuse - Blown and Short to Ground No Longer Exists

' 52 Backup Power Supply - Voltage Boost Fault

' 53 Internal Diagnostic Monitor Fault

Lowest -- Rapid Continuous Flashing of Air Bag Lamp - All Crash Sensors Disconnected

Hope this helps...

Seems to be a very common problem with Ford. The wiring harness beneath the drivers seat contains the sensors for the airbag system. Go under the drivers seat and secure all the wires and clips. This makes most error lights for the airbags go away. Hope this helps and good luck!