Question about 2003 Ford Crown Victoria

Open Question

Where do you find the neutral safety switch on a 2003 ford crown victoria?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Mike Grimes

  • 102 Answers

SOURCE: how to trouble shoot starting system 98 ford crown victoria

Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...

Posted on Sep 23, 2009

Ad

Anonymous

  • 104 Answers

SOURCE: 2003 Ford Crown Victoria misfires when

I HAVE HAD THE SAME PROBLEM ON SEVERAL CROWN VICS I HAVE WORKED ON ,& SOME OF THEM A SET OF PLUGS STOPPED IT,AND SOME OF THEM HAD TO HAVE 1 OR MORE COIL PACKS REPLACED, BUT THE PROBLEM THAT I FOUND THAT IF PLUGS & ALL COIL PACKS HAD BEEN REPLACED,AND IT WAS STILL IN THE IGNITION, IS THE WIRES GOING INTO THE PLUG ON THE COILPACK UNDER THE INTAKE TUBE, IF YOU REMOVE THE INTAKE TUBE,LOOK CLOSE AT THE WIRES FOR ANY BARE SPOTS,& LOOK AT THE BOTTOM OF THE INTAKR TUBE IF YOU CAN SEE WHERE IT HAS RUBBED IT,IT IS ALMOST A GIVEN THERE IS A BARE SPOT OR CRACKED INSOLATION ON THE WIRE, ENOUGH TO CAUSE A MISFIRE, (FYI) IT TOOK ME MANY TIMES OF INSPECTING BEFORE I LOOKED CLOSE ENOUGH TO SEE THE BARE SPOTS, BUT ALL YOU HAVE TO DO IS STRIP THE HARD PLASTIC AROUND THE WIRES BACK ENOUGH TILL YOU SEE GOOD CLEAN LOOKING WIRE,THEN SEPERATE THE WIRES AND IF YOU HAVE LIQUID ELECTICAL TAPE USE THAT AND THEN TAPE THEM WITH ROLL ELECTRICAL TAPE ,BUT IF YOU TAPE THEM UP GOOD SO WHEN THE WIRE IS BENT ENOUGH FOR THE INTAKE TUBE TO CLEAR ,& YOU CANNOT SEE THE WIRES GOING IN TO THE PLUG WITH A ROLL OF ELECTRICAL TAPE THAT WILL WORK TOO, I HOPE THIS TRICK WILL WORK AS GOOD FOR YOU AS HAS ME ON DOZENS OF CROWN VICS, ESPECIALLY P71 POLICE CARS.

Posted on Dec 05, 2009

anthony ventura

  • 180 Answers

SOURCE: ford crown victoria

you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Posted on May 11, 2010

The_UG

  • 74 Answers

SOURCE: I need the exact location of the neutral safety

Ford claims a special tool is required to pull the part, but as long as you can find a way to get it out without breaking it, success right? Anyway, If the open end of the bell housing is 12 o'clock and the output shaft is 6, the neutral start switch is located at 9 o'clock, just above the shift lever on the transmission housing.

Posted on Jun 04, 2011

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: where is the neutral safety switch located on 1998

On 1992 and later models, the neutral safety switch is incorporated into the Manual Lever Position or Transmission Range MLP/TR sensor.

RENOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely on jackstands.
  3. Place the transmission in Neutral.
  4. Remove and discard the manual control lever nut, then remove the lever from the transmission.
  5. Detach the TR sensor electrical harness connector, remove the TR sensor retaining bolts, then pull the TR sensor off of the transmission case.
To install:
  1. Position the TR sensor against the transmission case and loosely install the 2 retaining screws.
  2. Attach the TR sensor electrical harness connector.
  3. Use an alignment tool, such as the TR Sensor Alignment Tool T93P-70010-A, to align the TR sensor slots.
  4. Tighten the TR sensor bolts to 80-100 inch lbs. (9-11 Nm).
  5. Position the manual control lever onto the TR sensor, then install the new lever nut to 22-26 ft. lbs. (30-35 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
ADJUSTMENT
zjlimited_779.gif


Fig. : Adjusting the MLP sensor (click image for zoom)


Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.

  1. Position the manual control lever in Neutral .
  2. Raise the and safely support the vehicle.
  3. Loosen the sensor retaining bolts.
  4. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  5. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  6. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).
  7. Lower the vehicle.
Hope this helps (remember to rating ans leave a testimonial commnet about this free answer).

Posted on Oct 11, 2011

Testimonial: "Hey thanks very much...you must have had one a these crown vic's....I must get a manual for sure as I intend to keep her for a time. Thanks ZJ Limited"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 crown vic wont start


Are you saying it won't crank, or won't start ?
If it does not crank, and you have replaced the battery and starter, the problem may be in the neutral safety switch.

Dec 08, 2012 | 1999 Ford Crown Victoria

1 Answer

Where is the netural safty switch 1992 crown victoria


the neutral safety switch is on the metric tranny with wires coming out of it up to the engine

Dec 04, 2012 | 1992 Ford Crown Victoria

1 Answer

2000 FORD CROWN VIC GETTING POWER TO STARTER ,BATTERY FULL CHARGE CAR WONT TURN OVER


I would check for voltage at the starter from the battery and from the key switch via the neutral safety switch.
If there is no voltage at the starter from the battery check the fuseable link wires and the ground connections.

Sep 05, 2012 | 2000 Ford Crown Victoria

2 Answers

I have a 93 crown victoria and it runs great but more often when I put it into park it doesnt want to start again. I have to reput it in park 3 or 4 times.


Bad PRNDL switch(park/reverse/neutral/drive/low).May be adjustable,but most likely the switch is bad.As a temporary/free solution,try starting in Neutral(USE YOUR PARKING BRAKE!)

Mar 14, 2012 | 1993 Ford Crown Victoria

2 Answers

2004 Crown Vic Police car the starter tries to engage while shifting from Neutral to Drive, any ideas?


The ignition switch and/or neutral safety switch is failing.
Please do not use the vehicle until you are able to inspect the ignition switch,the wire harness connected to the ignition switch and neutral safety switch + the recall on the wire insulator.
The starter gear can damage the flywheel and cause LABOR INTENSIVE repair.
====
Please check the service record the 2004 recall on selected Crown Vic Police car.
Link HERE for the official NTSA recall notice on wiring insulator.
Call your local Ford dealer,provide you VIN number and reference recall NHTSA Campaign ID number : 05V206000
====

Feb 07, 2011 | 2004 Ford Crown Victoria

1 Answer

I need the exact location of the neutral safety switch on 1990 crown victoria


Ford claims a special tool is required to pull the part, but as long as you can find a way to get it out without breaking it, success right? Anyway, If the open end of the bell housing is 12 o'clock and the output shaft is 6, the neutral start switch is located at 9 o'clock, just above the shift lever on the transmission housing.

Nov 28, 2010 | 1990 Ford LTD Crown Victoria

1 Answer

Ford crown victoria


you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Mar 06, 2010 | 2001 Ford Crown Victoria

1 Answer

My car won't shift out of park, 1993 ford crown victoria i need to know the location of the sclu switch and/or the park sense switch


Check to make sure your brake lights are functioning properly. The crowns vics of that year have a neutral safety switch that links the shifter to the brake lights.

If the brake lights don't turn on = it won't come out of gear

If they do turn on = it could be that the neutral safety switch is out of place or malfunctioning.

I do believe that the neutral safety switch in that model should be located near the firewall attached to the upper side of your steering column.

You can easily get a manual for your car or look it up at the library to find it's exact location. Or try asking at your local auto parts store.

Nov 11, 2009 | 1993 Ford Crown Victoria

2 Answers

How to trouble shoot starting system 98 ford crown victoria


Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...

Sep 21, 2009 | 1997 Ford Crown Victoria

2 Answers

2001 crown victoria


You need a new BRAKE PEDAL SWITCH

Aug 10, 2008 | 2001 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

Related Topics:

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...