Question about 2006 Dodge Stratus

Open Question

Where is the oil pressure switch for 2006 stratus 2.4l located?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
mx5turbo92

mx5turbo92

  • 545 Answers

SOURCE: trying to findout where the thermostat is located in a 2006 dodge stratus

= Partially drain cooling system below thermostat level.= Disconnect upper hoses at coolant outlet connector,upper hose,radiator <---->thermostat housing end
= Remove bolts attaching coolant outlet connector = Remove coolant outlet connector and thermostat.

Posted on Jun 03, 2009

Ad

Anonymous

  • 295 Answers

SOURCE: 2001 dodge stratus power steering pressure switch

On the top of the Rack and Pinion assemly. hope this helps.

Posted on Jul 08, 2009

ministock48

Bobby Memory

  • 258 Answers

SOURCE: Location of master power window switch in 2006

the window switches in the drivers door is the master switch

Posted on Oct 17, 2009

Anonymous

  • 1 Answer

SOURCE: oil pressure sending unit location

oil pressure sending unit show location on 2000 dodge caravan V-6

Posted on Nov 28, 2009

tunde007

Tunde Autos

  • 2382 Answers

SOURCE: I need to know where

Hi, the Oil Pressure Switch is located Under hood, center, rear right side of the engine area, mounted on lower block. The switch is covered by a triangular shaped heat shield that is secured by three bolts.

Posted on Jan 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pressure sensor located on a 2005 dodge stratus


on the backside of the engine block, near the transmission bellhousing

Aug 02, 2014 | 2005 Dodge Stratus

2 Answers

Lwhere is oil pressure sending unit on 2006 dakota v6 located?


Location of the OPS unit is at the rear of engine near the distributor. (OPS) oil pressure sending

Jul 11, 2014 | 2004 Dodge Stratus

1 Answer

Replace oil pressure switch on a 2006 nissan xterra


It's located by oil filter,may have to remove filter to remove switch,may need a stubby(short) wrench to remove,may be able to turn tiresout to get to,it's a tight fit.Remove electrical connector,then get wrench and remove,then take to Autozone and match up with new one,here it is. Duralast Oil Pressure Switch PS561 2006 Nissan Datsun Xterra 2WD 6...

Jan 22, 2014 | 2006 Nissan Xterra

1 Answer

Location oil pressure sending unit 2004 stratus


The change oil light tells you when to change oiul,If after an oilchange the light did not go out it must be reset.
Location oil pressure sending unit 2004 stratus Google Search

Jan 29, 2018 | Chrysler Voyager Cars & Trucks

1 Answer

Oil light on at stop


engine oil pressure may be low remove oil pressure sending unit and install a pressure gauge check for pressure while warm if pressure is ok replace oil pressure sending unit oil pressure at idle should be between 5-15 psi at min

Nov 17, 2009 | 2006 Dodge Stratus

1 Answer

Oil sensor replacement for 2006 GTO


COST Around $25 - $35 and Fallow these Instructions PLEASE RATE ME!!!!!

Engine Oil Pressure Sensor and/or Switch Replacement

Tools Required
  • J41712 Oil Pressure Switch Socket
Removal Procedure
Disconnect the oil pressure sensor electrical connector (1).
  1. Important: Clean the area around the sensor before removal. This prevents debris from entering the engine. Use J41712 to remove the oil pressure sensor from the engine block.
Installation Procedure
  1. If installing the old sensor, apply thread sealant GM P/N 12346004, (Canadian P/N 1093480), or equivalent. Notice: Refer to Fastener Notice in Service Precautions.
  2. Use to install the J41712 oil pressure sensor to the engine block. Tighten the engine oil pressure sensor to 35 Nm (26 ft. lbs.) .Connect the oil pressure sensor electrical connector (1).

Oct 04, 2009 | 2006 Pontiac GTO

1 Answer

Oil pressure sending unit location


oil pressure sending unit show location on 2000 dodge caravan V-6

Mar 23, 2009 | 1997 Dodge Stratus

5 Answers

Where is the oil pressure sending unit on 2004 dodge stratus?


per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Jan 23, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
2006 Dodge Stratus Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...