SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic
Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.
IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)
When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...
SOURCE: Replace a starter
1999 Honda Civic DX 1.6L MFI SOHC 4cyl
Starter Removal & Installation
Fig. Starter wire connections
Fig. A ratchet and long extension may be needed to remove the starter
The factory sound system has a coded theft protection system. It is recommended that you know your reset code before you begin.
To install:
When installing the heavy gauge starter cable, make sure the crimped side of the terminal end is facing out.
I hope help you with this (rated this help). Good luck.
SOURCE: how to dismantle console box of honda civic 2008
1.
Alright, let's just jump right into it. Get down and low and at the front of your center console you'll find two clips holding it in. There's one on the driver's side and one on the passenger side.
Okay so now how the *#$@ do I remove those clips? If you pull they don't come out...and if you pry you'll just scratch your console. Here's how: Look carefully and you'll see the center is a little circle. Gentley push it in...voila..off it pops. Repeat this for the other side.
2.
Alright now it's time to head to the back. You should recline your seats all the way forward and slide them up front. This will give you plenty of room to work. Get down low and you'll see a screw holding the back in -- once again you'll find it on both sides.
Simply take your Phillips head screwdriver to the ****** and unscrew it on both sides.
3.
Look carefully and you're going to see that the top of your center console is comprised of two pieces. One that stretches from the front of the console to just behind the shift boot. The second piece stretches from there to the back of the console.
The second piece is what we're going to remove. Here's how to do it. It's only held down by a few clips so all you need to do is pry it up. So whip out your flat head screw driver, or other prying device along with a cloth to prevent your crazy @$$ from prying up the plastic too. Start and the back and pry it up.
4.
You can theoretically now just pull the whole thing straight up. However what I found to be easier was to pry up one side and get your fingers underneath then pull from left to right (or vice versa) to pop off the front clips. The front clips tend to be in stiffer than the ones around the side and rear.
*POP* The entire center piece should now be free!
5.
Now you're able to lift the piece straight up.
Simply slide the piece up and forward taking care not to scratch anything
6.
Alright you'll probably discover you can't quite get it past the brake lever.
Yup...excellent deduction Sherlock..the gear shifter seems to be in the way.
7.
Alright time to move out of the way Mister Gear Shifter
Slide that baby into 1st gear (Make sure you didn't lower your hand brake!!!)
8.
It's free! Now you have room to work!
Okay now that the gear shift is in first...you have room to carefully slide the piece forward and out without scratching anything.
So now that you have the rear piece off, you want to remove the front piece right?
Well as you can see here, all that's holding it in place are these two screws on this panel.
Take your mighty Phillips head screwdriver and go buck-wild on those two screws
You've now successfully removed everything that's been holding the center console down.You should now be able to slide the center console back and forth. There you should be able to remove it now..and you should see this
SOURCE: need to replace distributor on 99 honda civic lx
How do you install a distributor on a 1999 Honda Civic?
SOURCE: Honda civic 2008 - panic button on the key
Placed jumper cables on the car to try & jump alarm sounded pressed the unlock button & was then able to start car without any problems.
88 views
Usually answered in minutes!
Thank you. It doesn't make a grinding noise. The only thing is that everything is on as fat as the radio, the panel is on, but when I turn the key, the car won't start. Just making a one click noise.
Hello, I'm having the same problem. What turned out to be the problem with your car if you don't mind me asking?
×