Question about 2000 Dodge Ram 1500 Truck

Open Question

Truck wont fire up no bus code on odometer

Truck runs fine then after i turn it off it wont star for a while

Posted by on

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 702 Answers

SOURCE: odo'no bus after mileage flashes four times 99 dodge dakota

Clean your negative battery cable end and battery post. The "no bus" usually is caused from a bad ground.

Posted on Dec 21, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: 1999 dodge durango 5.9 cranks but wont start no

It is your computer. I had this recently as well. No Bus means no connection to the on board computer. There is a company in Florida that repairs these computers, so don't get suckered in by the dealership for 750-1000.

Posted on Mar 25, 2009

carlsbiz

Carl

  • 1124 Answers

SOURCE: 1999 dodge durango slt stalls but restarts (no

It could be water in the gas.. Get some "dry gas' aditive and follow directions..
It could also be the fuel filter.. Try replacing it..
I have seen this happen on several Dodge's..
The fuel filter gets clogged and choked the engine at idle..

Good luck..

Posted on Sep 21, 2009

Anonymous

  • 36 Answers

SOURCE: Having issues with a 2000 Dodge Ram. The engine

Could be a wiring and or PCM issue. Has it ever been wrecked or had the A/C worked on. Check for any pinched wires. Might be as simple as unpinching the harness.

Posted on Nov 15, 2009

Guateman

  • 2 Answers

SOURCE: i have a 99 dodge

The cluster work from 2 wires can bus a lot of times is the sensor ground not connected.

Posted on Jul 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pt cruiser wont start. checked battery, starter , releighs and ignition, and they seem fine. no codes come up when turning the key 3 times


To do self diag on a pt u need to start with ignition off. Hold trip button in for the odometer keeping trip button held down turn ignition key to run then release trip. This will also run a self test on instrument cluster. Codes will be displayed in the odometer at the end of test

Nov 01, 2016 | Chrysler PT Cruiser Cars & Trucks

1 Answer

My 03 dodge 3500 5.9. is showing a no bus error code on odometer the truck starts fine but gauges aernt working


The BUS is not part of the PCM/ECM it is on the body control module (BCM). It effects radio and dash most noticeably. Has no effect on powertrain.

Jan 16, 2014 | 2001 Dodge Ram 3500 Truck

1 Answer

My 2002 wont turn over givbing me a no bus what do i do


make sure wires to battery are tight and making good contact

Feb 17, 2013 | 2002 Chrysler Sebring

2 Answers

No Bus 08 dodge avenger..windows,radio,heater...etc..no start..disconnect battery..now its running again


Just bought a 2013 dodge avenger, literally yesterday. Test drove fine twice,, drove all over town for license and registration, multiple erands. No problems. I got to work and went to leave for lunch and was introduced to the no bus code. Left me stranded the very day i purchased it,, only 25000 miles. Is this problem simple enough to weather or is this the brightest red flag to take it back?

Jan 21, 2012 | Cars & Trucks

1 Answer

My odometer code no bus and it wont start 1999 dodge durango


Check for a faulty crank sensor. Sounds strange, but we found this out the hard way in the dealerships,many years ago. Following the trouble tree usually lead to pcm replacement, and it still wouldn't run.

Sep 01, 2011 | 1999 Dodge Durango

1 Answer

My 2007 dodge nitro has an error code "no bus" how do i fix it?


well :no bus: means that the infomation panell is not getting a signal check the harness below the odometer. I guess the car is running fine, if not then its the ecu itself.

Oct 01, 2010 | 2007 Dodge Nitro R/T New Cars

1 Answer

2001 Dodge Ram, 3500, CTD 5.9, AT, 2WD, No Bus


No bus error code has nothing to do with your fuse panel this is a ECM /ECU error code... sorry but get ready to spend some money for a new ECM

Sep 13, 2009 | 2001 Dodge Ram 3500 Truck

2 Answers

Wont start my odometer blinks and says no bus


From the official Durango shop manual......(abbreviated)

Self Diagnosis Test

Vehicle key position is OFF ,or able to pull key out.
Hold in the trip odometer button (dont release yet)
Turn key to the ON position (one notch), but DON'T try to start the engine
Continue holding the trip button for about 10-12 seconds until CHEC appears in the odometer display
Release the trip button.
Series of three digit numeric failure codes may appear.
If no failure message appears, the self diagnostic test will proceed as described in step 6


Code Chart

110- cluster CPU,RAM,EEPROm failure, replace cluster

900-CCD data bus not operational, check CCD data bus connections at cluster, check the cluster fuses,check the CCD data bus bias, cehck the CCD data bus voltage, check the CCD data bus terminations.

920-cluster is not recieving a vehicle speed message from the PCM, check PCM software level and reflash if required, use the ($2500+) DRBIII scan tool to verify the vehicle speed message is being sent by the PCM

921-the cluster is not recieveing a distance pulse message from PCM,check PCM software level and reflash if required, use the ($2500+) DRBIII scan tool to verify the distance pulse message is being sent by the PCM

940-the cluster is not recieving an airbag lamp-on message from the ACM, check the CCD data bus connections at the ACM, check the ACM fuse.

950-cluster not recieving an ABS lamp-on message from the CAB, check CCD data bus connections at the ACM, check the ACM fuse.

960- clsuter not recieving a PRND21 message from the TCM, check the CCD data bus connections at the TCM, check the TCM fuse.

999-An error has been discovered, record the failure message, depress the trip odometer reset button to continue the Self-Diagnostic Test

Step 6
Instrument cluster will test each segment of the odometer (all first, then each one seperately)

Step 7
Bulb test

Step 8
Gauge test

Step 9
test completed

The instrument cluster will return to normal operation at the completion of test, if ignition switch turned off, or a vehicle speed message indicating movement recieved from the PCM on the CCD data bus.

Hope that help you or anyone else in future.

Aug 10, 2008 | 2000 Dodge Durango

1 Answer

2000 dakota v8 won't start


It sounds like it jumped time

Apr 23, 2017 | 2000 Dodge Dakota Quad Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...