Find and replace canister purge valve for 2002 honda accord

code p 0497 refers to evaporative emission system ---low purge flow====causes ---wiring---EVAP valve ---hoses blocked ---mechanical fault

Look at this information and don't ever over fill the car as it can push fuel into the emissions canister and cause problems.
http://honda-tech.com/honda-accord-1990-2002-2/98-accord-problem-code-p1456-2460060/

code p1456 refers to evaporative emission (EVAP) canister purge system(fuel tank system) -leak detected===causes--hose-fuel tank/pressure sensor--fuel filler cap--EVAP valve /bypass solenoid--EVAP two way valve---EVAP canister/vent valve

There is also a second reference to the code which is EVAP system leakage ====filler cap--EVAP canister purge valve--hoses---EVAP canister shut off valve---ECM programming---ECM

Check with the service dealer that the filler caps are interchangeable . It may be coincidence that the problem started after you changed caps or it may have shown a failure in the making

Hi James,
Kindly check this website for you for detailed description of code P1456.
P1456 Honda Evaporative Emissions Control System Leakage Fuel Tank

Just replace the evap purge valve.

P1457 HONDA - Evaporative Emissions Control System Leakage EVAP Canister Systemhttp://engine-codes.com/p1457_honda.htmlForum CodePossible causes- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap There is a Honda factory service bulletin with information on how to diagnose the P1456 on the following Honda models:
1998 Honda Accord
1999 Honda Accord
2000 Honda Accord
1998-2000 Honda Accord
symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vaporsP1457 HONDA Description The evaporative emission (EVAP) control system stores fuel vapor from the fuel tank in the EVAP canister temporarily to prevent it from escaping to the atmosphere and to enable it to be drawn into the engine by intake manifold vacuum and burned. In addition, the onboard refueling vapor recovery system (ORVR) stores fuel vapor generated when refueling in the EVAP canister.

The EVAP control system leak detection method improves the accuracy and frequency of the detection by determining faulty components and vapor leakage for each part. The EVAP control system (from the purge valve to the fuel tank) is divided into two parts. One is the "EVAP Canister Side" (from the EVAP two way valve to the purge valve) and the other is the "Tank Side" (from the EVAP two way valve to the fuel tank). There is 0.04 inch leak detection and 0.02 inch leak detection. If the 0.04 inch leak detection results are OK, the 0.02 inch leak detection runs. The P1457 code is detected when the EVAP system has a very small leak.

P0107 HONDA - Manifold Absolute Pressure Sensor Circuit Low Voltagehttp://engine-codes.com/p0107_honda.htmlForum CodePossible causes- Manifold Absolute Pressure harness is open or shorted
- Manifold Absolute Pressure sensor poor electrical circuit connector
- Faulty Manifold Absolute Pressure sensor
- Faulty Engine Control Module (ECM) When is the code detected?An excessively low voltage from the sensor is sent to ECMSymptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Engine rough idle
- Engine hesitation
P0107 HONDA Description The Manifold Absolute Pressure sensor provides instantaneous manifold pressure information to the engine's Engine Control Module. The data is used to calculate air density and determine the engine's air mass flow rate, which in turn determines the required fuel metering for optimum combustion. A fuel-injected engine may alternately use a Mass Air Flow sensor to detect the intake airflow. A typical configuration employs one or the other, but seldom both.


In some vehicles the absolute pressure sensor is built into ECM. HONDA Technical Service Bulletins for P0107 code1999 HONDA ODYSSEY Electrical System 2000 HONDA ODYSSEY Electrical System1998 HONDA ACCORD Electrical System 1999 HONDA ACCORD Electrical System 2000 HONDA ACCORD Electrical System 2001 HONDA ACCORD Electrical System 2002 HONDA ACCORD Electrical System 1996 HONDA CIVIC Electrical System 1997 HONDA CIVIC Electrical System 1998 HONDA CIVIC Electrical System

P1456 EVAP CONTROL SYSTEM LEAKAGE ( FUEL TANK SYSTEM)

There are a lot of potential leak points. The canister could be leaking, any number of the system hoses could leak. You could even have a leak in the fuel tank. Do you ever smell fresh gas?

Trouble Code: P1456


EVAP System Very Small Leak (0.020") Detected

Possible Causes:


EVAP control system pressure sensor is damaged or has failed

EVAP purge solenoid is damaged or has failed

EVAP canister vent control valve is damaged or has failed

Fuel tank cap not tightened properly or the wrong part number

Fuel tank temperature sensor is damaged or has failed

Fuel tank vacuum relief valve is damaged or has failed

Very small leak in the EVAP canister or in the fuel tank area

ORVR system is damaged or has a small leak in a component

Refueling control valve is damaged or has failed