Torque specs for rod bearings on a 2001 Chrysler Town and Country 3.8 also the position of the Piston is the notch go forward or is the F in the front of it go forward

https://www.torkspec.com//torkspecme.aspx?KI=7

This site will give you that information

of what , 6000 parts in the car./
name something, , is it drive line , engine, trans, axles parts. what?
or learn to buy the service manual and read it?

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

already answered here, 26 or 29 :>D

What are the torque specs for crankshaft main and rod - Fixya

https://www.fixya.com > ... > Buick > LeSabre
Sept 21, 2012 - The connecting rods torque to 29 foot pounds. ... Where is the eng control module in a 2005 Buick Rendezvous ultra 3.6 eng.
SOLVED: I need torque specs. for rod bearings and main - Fixya
Jun 2, 2011
Torque specs for intake on 2005 buick rendezsous - Fixya
Sept 7, 2019
Torque spec for1997 3.8 buick rod and mains - Fixya
May 22, 2012
What is the torque specks for a 3.8 lt v 6 rear main cap 1987 buick ...
Nov 14, 2019
More results from www.fixya.com

More here

https://www.google.com/search?q=05+Buick+Rendezvous+Ultra+3.6+piston+rod+torque
..

TORQUE SPECIFICATIONS
All readings in ft. lbs.
Year Engine Displacement Liters Engine VIN Cylinder Head Bolts Main Bearing Bolts Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Oil Pan Drain Plug Intake Exhaust 2008 3.3 H - - - 40 70 - 17 13 20 3.8 P - - - 40 70 - 17 13 20 4.0 X - - - 70 70 - 17 20 20 2009 3.3 H - - - 40 70 - 17 13 20 3.8 P - - - 40 70 - 17 13 20 4.0 X - - - 70 70 - 17 20


Main Bearing Torque Sequence


3.3L & 3.8L Engines Specific to:
Chrysler Town & Country 2008-2009
Dodge Grand Caravan 2008-2009

NOTE
Only one main bearing should be selectively fitted while all the other main bearing caps are properly tightened.

1.Before servicing the vehicle, refer to the Precautions Section.
2.Start a bearing in place, and insert Main Bearing Tool C-3059 into the oil hole of the crankshaft.
3.Slowly rotate the crankshaft counterclockwise sliding the bearing into position. Remove Special Main Bearing Tool C-3059.
4.Inspect the main cap bolts for stretching. Replace the bolts that are stretched.
NOTE
The main cap bolts should be examined before reuse. Bolt stretch can be checked by holding a scale or straight edge against the threads. If all the threads do not contact the scale, the bolt must be replaced.

5.Install each main cap and tighten the bolts finger tight.
6.Tighten number 1, 3, and 4 main cap bolts to 30 ft. lbs. (41 Nm), plus 1 / 4 turn.
7.Rotate the crankshaft until the number 6 piston is at Top Dead Center (TDC).
8.To ensure correct thrust bearing alignment, the following procedure must be done:
A.Move the crankshaft all the way to the rear of its travel.
B.Then, move the crankshaft all the way to the front of its travel.
C.Wedge an appropriate tool between the rear of the cylinder block and the rear crankshaft counterweight. This will hold the crankshaft in its most forward position.
D.Tighten the No. 2 Thrust Bearing cap bolts to 30 ft. lbs. (41 Nm), plus

2001 Chrysler Town Country Caravan Voyager Service Repair Workshop Manual...


for easy and best solution go to this li

Torque Specs Database

Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

http://ww2.justanswer.com/uploads/ZZdaryl/2009-06-14_153454_torque.pdf

Main Bearing Cap Bolt 4.3L Step 1 15 ft lbs (20) Step 2 Additional 73 Degrees

i don't know if that's correct for main bearing caps since another link states it's much higher

4 3 Vortec Piston Specs eHow

hopefully a GM guy will chime in to confirm the main bearing torque

the rod bearing torques are the same on all the other links

change front wheel bearing on 2009 Chrysler Town Country YouTube

i need torque spec on 2005 chrysler town and coutry van for transmission bolts are 10 m