Question about 2000 Jeep Cherokee

1 Answer

How do you remove the headrest on a 2000 Jeep Cherokee

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Factory service manual 2000. I posted the book free here 300 times.
as they say RTM , read the manual>?
Ill quote the pages for you .

"REMOVAL AND INSTALLATION
HEAD RESTRAINT SLEEVE
REMOVAL
NOTE: When replacing a head restraint sleeve, the
retaining tabs on the sleeve will be damaged during
the removal process. Check the availability of
replacement parts before servicing.

(1) Raise head restraint to the full up position.
(2) Turn head restraint lock thumbwheel to release
head restraint and pull head restraint upward to
remove from seat back.
(3) Insert head restraint sleeve extractor (special
tool 6773) (Fig. 1) and (Fig. 2) into the seat back.
(4) The retaining tabs are positioned on each side
of the sleeve, when inserting the extractor, ensure
that the flat of the collar is facing the side of the
seatback (Fig. 3).
(5) Using a small hammer, tap extractor downward
to release sleeve retaining tab.
(6) Remove extractor tool from sleeve, rotate tool
180 degrees (Fig. 4) and repeat steps 3 and 4.
(7) Remove extractor tool from sleeve and remove
sleeve from seat back."


How do you remove the headrest on a 2000 Jeep Cher - 26297855-cv3cea42xo3hns4wc2h2eyux-1-0.jpg

Posted on Oct 21, 2016

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 3 Answers

SOURCE: headrest 2000 neon

hey u may have figured it out already ,but if u look under the head rest u should feel the two long iron poles going into the head rest on one side of one of them theres a button that blends rite into the design of it so look carefully

Posted on Jul 26, 2008

Anonymous

  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

Richard Scordino

  • 6982 Answers

SOURCE: 2000 jeep grand cherokee 4.0 liter engine timing belt replacement

If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Posted on Apr 05, 2009

Richard Scordino

  • 6982 Answers

SOURCE: I have a 2001 Jeep Cherokee - need rear seat with headrests -

Don't remember ever seeing one. You can make anything fit anything if dimensions are close but since your seat folds, it will take extensive work to put anything in there. likely easier to install some kind of roll bar (semi permanent) with head supports. that way you can remove it if you need the space. Nothing there will be cheap or easy though.

Posted on May 14, 2009

Laurie Schloss

  • 1 Answer

SOURCE: Replacing water pump on 2000 Jeep Grand Cherokee V6

i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the 3rd row headrests from a 2007 Jeep Commander?


Their held in with a snap ring or look at where they mount to the seat. If you see screws/bolts, take them out. If not you will have to pry/pop them out.

Nov 30, 2014 | 2007 Jeep Commander 3.0

1 Answer

How to get front dash off on jeep cherokee model 2000 at ac controll


how to remove a cluster from a 2000 jeep cherokee?

Jul 20, 2012 | 2000 Jeep Cherokee

1 Answer

I'm trying to locate the thermostat on my 2000 jeep grand cherokee


  1. On 2000 Jeep Grand Cherokee 4.7L V8
  2. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  3. Remove thermostat housing mounting bolts, thermostat housing and thermostat.

2000 Jeep Grand Cherokee 4.0l v6
Note:on the In-line 6 4.0L model the thermostat housing is mounted at the top of the engine block next to the water pump.

Nov 14, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Removing the headrest on a 2000 ford mustang gt


1. Lift headrest and headrest support bars trim all the way up.

2. Insert tongue depressor (or slim jim) down the front side of the headrest bar. Push depressor down as far as possible. When the depressor is beneath the headrest trim piece, push headrest all of the way down.

3. Lift headrest to remove.

Jul 05, 2010 | 2000 Ford Mustang

1 Answer

Headrest inserted backwards and now unable to


On my 2003 Jeep, there is a button on one of the two round plastic bases in the top of the seat. The button is actually molded the shape of the base. Depress it while pulling the headrest upwards.

Dec 11, 2009 | 2004 Jeep Grand Cherokee

1 Answer

I have a 2001 Jeep Cherokee - need rear seat with headrests -


Don't remember ever seeing one. You can make anything fit anything if dimensions are close but since your seat folds, it will take extensive work to put anything in there. likely easier to install some kind of roll bar (semi permanent) with head supports. that way you can remove it if you need the space. Nothing there will be cheap or easy though.

May 14, 2009 | 2001 Jeep Cherokee

1 Answer

Head rest


http://www.scribd.com/doc/2050325/2004-WJ-Jeep-Grand-Cherokee

click this link directly its the manual of your vehicle.everything is mentioned.
It's pretty easy. Raise the headrest all the way up. Look at the plastic pieces on the seat where the headrest supports go into the seat. One of them will have a small hole. Get a paperclip and push it into the hole while pulling up on the headrest and it will come out.

May 03, 2009 | 2006 Jeep Grand Cherokee

1 Answer

Need to remove head rest to put on seat covers


I looked into new headrest for my 2005 Grand Cherokee with the monitors installed in them. I had mine off but couldn't remember how i did it. But I got the instuctions from the the company with the new headrest and they linked me to a video online. The company was on ebay. I remember that it was really simple

May 02, 2009 | 2005 Jeep Grand Cherokee

2 Answers

Replacing water pump on 2000 Jeep Grand Cherokee V6


i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Jan 10, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Cherokee Logo

Related Topics:

427 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...