Need correct position of rear bracket - 1996 Dodge Caravan

Question edited for clarity, add maker.
Question moved to model category.

Check out the diagram

https://www.hsfmanual.com/shift_cable_repair_procedures-345.html

and the videos.

https://www.google.com/search?q=2002+Hyundai+Santa+Fe.+Correct+position+for+shifter+cable+bracket

..

5) Install the rear A/C mountingbracket. Tighten the rear A/C mounting bracket bolts to 35 Nm (26lb-ft).6) Install the A/C compressor. 7) Install the power steering pump. 8) Connect the negative battery cable.
If this helps, please say so! Thanks! :-)

if it came unglued from glass which is what it sounds like, any auto parts store should have a special package of "rear view mirror glue or cement" it is on the shelf. it should come with the all important cleaning solution or wipe, but before you clean (scrape with razor blade scraper, glass and bracket )off old glue, mark the position of mirror, do this on inside or outside of glass with tape or a marker. the mirror has a bracket its mounted to, look closely for a set screw and remove bracket, it might be a tiny slotted screw or hex head (allen head ) note position of bracket in relation to mirror because your going to glue the bracket only to the glass at first and when the bracket is upright the mirror will slide down on to bracket, then tighten the set screw! be sure to follow instructions EXACTLY on package of glue. would be a good idea to get two packs, just in case first try goes awry. its cheap!

Hello,

• Remove air cleaner and duct assembly.
• Drain coolant into a suitable container.
• Loosen engine mount strut to engine mount strut bracket bolts.
• Loosen engine mount strut bracket brace bolts from upper radiator support bracket.
• Remove mounting bolts on radiator upper support and position engine mount strut and bracket to rear.
• Ensure ignition switch is in Off position, then disconnect cooling fan.

Thanks

Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Joe
Thanks for choosing Fixya!

Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .
hope this helps . please rate my response.

Camshaft Position Sensors are located on the cylinder head according to the following: Camshaft, Bearings & Lifters Removal & Installation To Remove:

1. Remove the engine from the vehicle.
2. Remove the front suspension member, transaxle and transfer case (if equipped) from the engine.
3. Mount the engine in a suitable engine stand.
4. Remove the timing chains and rear timing chain case.
5. Remove the camshaft position sensors from the cylinder heads.
6. Remove the intake valve timing control solenoid valves. NOTE: Mark the camshafts, camshaft brackets, and bolts so they are placed in the original locations during installation.
   
7. Loosen the camshaft bracket bolts in several steps using the order shown.
8. Remove the intake and exhaust camshaft brackets and the camshafts. Camshaft bracket bolt removal sequence
   
   
9. Remove the valve lifters and the secondary timing chain tensioner with stopper pin attached if necessary.

NOTE: Stopper pin was installed when the secondary timing chain was removed.
To Install:
NOTE: Clean sealant from front camshaft bracket, bolts and bolt holes.

1. Turn the crankshaft until No.1 piston is at TDC on the compression stroke. The crankshaft key should line up with the right bank center line as shown. Crankshaft keyway position
   
   
2. If removed, install the secondary timing chain tensioners and valve lifters in their original positions. NOTE: The intake camshaft has a drill mark on the edge of the sprocket mounting flange.
   
3. Position the camshafts on the cylinder heads with the dowel pins as shown. Camshaft dowel pin positions
   
   
4. Apply silicone sealant to the front (No. 1) camshaft bracket as shown. Apply silicone sealant to the front (No. 1) camshaft bracket
   
   Camshaft bracket bolt installation sequence
   
   
5. Install and tighten the camshaft brackets using the following steps in the sequence shown;
   • Step 1 (bolts 7 - 10) : 1 ft-lb (2 Nm)
   • Step 2 (bolts 1 - 6) : 1 ft-lb (2 Nm)
   • Step 3 (bolts 1 - 10): 4 ft-lbs (5.9 Nm)
   • Step 4 (bolts 1 - 6) : 8 ft-lbs (10.4 Nm)
   • Step 4 (bolts 7 - 10) : 7 ft-lbs (9.3 Nm)
6. Wipe off excess sealant from bracket No. 1.
7. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head. The specification is -0.0055 to 0.0055 in (-0.14 to 0.14 mm). Replace the camshaft and camshaft bracket if out of specification. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head
   
   
8. Install the IVT control solenoid valves with new gaskets.
9. If removed, install the camshaft position sensor.
10. Install the rear timing chain case and timing chains.
11. Install the engine in the vehicle.

Removal Procedure

Disconnect the negative battery cable

Remove the wheelhouse liner.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.


Install the battery hold down retainer and bolt.

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts.

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Install the positive battery cable (1).

Tighten the positive battery cable bolt.

Close the positive battery cable connection cover.

Install the wheelhouse liner.

Connect the negative battery cable

yes it will but your speedometer will not read right

Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
hope this helps