What is a fuel trim bank 1 on a 2006 xc90 volvo an whatvis a evap emission system switching valve mean

code p 0440 refers to evaporative emission (EVAP) system---malfunction===causes ---hose connections ---intake leak---EVAP canister purge valve
probably the purge valve needs replacing

code p 0172 refers to system too lean, bank 1===causes --intake blocked , EVAP canister purge valve ---fuel pressure ---EGR system---injector/s HO2S
you will notice that the purge valve is in both codes and it also affects the fuel pressure by not venting the tank correctly
That will account for the fuel pressure problem
I would seek advice from an accredited service specialist that works on your type of car but I would be paying attention to the common fault ( purge valve) before any thing else

HYUNDAI OBDII DTC

P1100 Manifold Absolute Pressure Sensor Range/Performance
P1102 Manifold Absolute Pressure Sensor Circuit Low Input
P1103 Manifold Absolute Pressure Sensor Circuit High Input
P1123 Lang Term Fuel Trim Adaptive Too Lean
P1124 Long Term Fuel Trim Adaptive Too Rich
P1127 Long Term Fuel Trim Multiplier Too Rich
P1128 Long Term Fuel Trim Multiplier Too Lean
P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)
P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)
P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)
P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)
P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)
P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)
P1372 Segment Time Incorrect
P1400 Manifold Differential Pressure Sensor Circuit
P1440 EVAP System Vent Solenoid Circuit
P1443 EVAP System Fault (Fuel Tank Cap Missing)
P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)
P1511 Idle Control Valve Command Signal Shorted (Coil 2)
P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)
P1521 Power Steering Switch Input Circuit
P1529 Customer Snapshot Request VIA CAN
P1552 Idle Air Control Valve Closing Coil Circuit Shorted
P1553 Idle Air Control Valve Closing Coil Circuit Open
P1586 Encoding Signal Circuit Not Rationale
P1602 Serial Communication Fault with Transmission Control Unit
P1605 Rough Road Sensor Circuit
P1606 Rough Road Sensor Circuit Not Valid
P1611 MIL Request Signal Circuit Low Input
P1613 ECU Self-Test Failed
P1614 MIL Request Signal Circuit High Input
P1616 Main Relay Fault
P1623 Diagnostic Lamp Power Stage Fault
P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit
P1625 Cooling Fan Relay High Circuit
P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault

EOBD II Error Code: 25
Description:
System too Lean, Bank 1
Possible Causes:
- Intake/exhaust leak.
- Secondary air injection (AIR) system.
- Manifold absolute pressure (MAP) sensor.
- Mass air flow (MAF) sensor.
- Fuel pressure/pump.
- Injector(s).
- Evaporation emission (EVAP) canister purge valve.
- Heated oxygen sensor (HO2S).
- Contaminated fuel.

EOBD II Error Code: 26
Fault Location:
System too Rich, Bank 1
Description:
- Evaporation emission (EVAP) canister purge valve .
- Fuel pressure.
- Injector(s).
- Heated oxygen sensor (HO2S).
- Contaminated fuel.
Hope that works.

P1100 Manifold Absolute Pressure Sensor Range/Performance
P1102 Manifold Absolute Pressure Sensor Circuit Low Input
P1103 Manifold Absolute Pressure Sensor Circuit High Input
P1123 Lang Term Fuel Trim Adaptive Too Lean
P1124 Long Term Fuel Trim Adaptive Too Rich
P1127 Long Term Fuel Trim Multiplier Too Rich
P1128 Long Term Fuel Trim Multiplier Too Lean
P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)
P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)
P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)
P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)
P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)
P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)
P1372 Segment Time Incorrect
P1400 Manifold Differential Pressure Sensor Circuit
P1440 EVAP System Vent Solenoid Circuit
P1443 EVAP System Fault (Fuel Tank Cap Missing)
P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)
P1511 Idle Control Valve Command Signal Shorted (Coil 2)
P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)
P1521 Power Steering Switch Input Circuit
P1529 Customer Snapshot Request VIA CAN
P1552 Idle Air Control Valve Closing Coil Circuit Shorted
P1553 Idle Air Control Valve Closing Coil Circuit Open
P1586 Encoding Signal Circuit Not Rationale
P1602 Serial Communication Fault with Transmission Control Unit
P1605 Rough Road Sensor Circuit
P1606 Rough Road Sensor Circuit Not Valid
P1611 MIL Request Signal Circuit Low Input
P1613 ECU Self-Test Failed
P1614 MIL Request Signal Circuit High Input
P1616 Main Relay Fault
P1623 Diagnostic Lamp Power Stage Fault
P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit
P1625 Cooling Fan Relay High Circuit
P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault
esta codigo no lo existe in hyundai codigos

Error Code: P0172
Fault Location:
Fuel Trim, System too Rich, Bank 1
Possible Cause:
Evaporation emission (EVAP) canister purge valve.
Fuel pressure.
Fuel Injector(s).
Heated oxygen sensor (HO2S).
Mass air flow sensor.
Engine coolant temperature sensor.
Element air cleaner, clogged.

without knowing your make or model:

p1443
Evaporative Emission Control System Control Valve

audi
EGR Valve Position Sensor Signal Too Low

bmw
Leakage Diagnostic Pump Control Circuit Signal High

ford
EVAP Control System Purge Control Solenoid or Purge Control Valve Fault

hyundi
EVAP System Tank Cap Missing

infinity
Evaporative Emission Control System Control Valve

lexus
Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 2

mazda
Evaporative Emission Control System Large leak detected

mitsubishi
EVAP Purge Control Valve 2 Circuit Malfunction

nissan
Evaporative Emission Control System Control Valve

suburu
Evaporative Emission Control System Vent Control Function Problem

suzuki
EVAP Purge Control Valve Malfunction- Stuck Open

toyota
Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 2

volkswagon
EGR Valve Position Sensor Signal Too Low

code PO171 fuel trim system lean bank 1 conditions.possible causes air leaks in intake manifold exhaust pipes or exhaust manifold. fuel control sensor is out of calibration such as ECT IAT MAF.fuel component faulty like stopped up fuel filter fuel injectors clogged low fuel pressure faulty fuel pump. HO2S element contaminated or has failed. purge solenoid is part of EVAP system. if you have faulty purge solenoid you would get code like PO443 meaning evaporative emission control system purge control valve circuit malfunction.try replacing fuel filter clean fuel injectors see what happens.

iam posting the hyundai code list i have that the vehicle manufacturer lists

P1100 Manifold Absolute Pressure Sensor Range/Performance

P1102 Manifold Absolute Pressure Sensor Circuit Low Input

P1103 Manifold Absolute Pressure Sensor Circuit High Input

P1123 Lang Term Fuel Trim Adaptive Too Lean

P1124 Long Term Fuel Trim Adaptive Too Rich

P1127 Long Term Fuel Trim Multiplier Too Rich

P1128 Long Term Fuel Trim Multiplier Too Lean

P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)

P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)

P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)

P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)

P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)

P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)

P1372 Segment Time Incorrect

P1400 Manifold Differential Pressure Sensor Circuit

P1440 EVAP System Vent Solenoid Circuit

P1443 EVAP System Fault (Fuel Tank Cap Missing)

P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)

P1511 Idle Control Valve Command Signal Shorted (Coil 2)

P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)

P1521 Power Steering Switch Input Circuit

P1529 Customer Snapshot Request VIA CAN

P1552 Idle Air Control Valve Closing Coil Circuit Shorted

P1553 Idle Air Control Valve Closing Coil Circuit Open

P1586 Encoding Signal Circuit Not Rationale

P1602 Serial Communication Fault with Transmission Control Unit

P1605 Rough Road Sensor Circuit

P1606 Rough Road Sensor Circuit Not Valid

P1611 MIL Request Signal Circuit Low Input

P1613 ECU Self-Test Failed

P1614 MIL Request Signal Circuit High Input

P1616 Main Relay Fault

P1623 Diagnostic Lamp Power Stage Fault

P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit

P1625 Cooling Fan Relay High Circuit

P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault

P0171 - System to Lean (Bank 1)
P0174 - System to Lean (Bank 2) Lack of fuel or too much air - unmetered air after the mass air flow sensor ! vacuumn leak . Not enough fuel - low fuel pressure , clogged injectors .
P0171 - System to Lean (Bank 1) The Adaptive Fuel Strategy continuously monitors fuel delivery hardware. The test fails when the adaptive fuel tables reach a rich calibrated limit. Refer to Section 1 , Powertrain Control Software, Fuel Trim for more information. Air Measurement System

• MAF sensor (contaminated, damaged, malfunctioning, etc.)

Fuel System

• Fuel pressure regulator (leaking, malfunctioning, etc.).
• Fuel filter plugged, dirty.
• Fuel pump (weak, check valve leaking, etc.).
• Leaking/contaminated fuel injectors.
• Low fuel pressure or running out of fuel.
• EVAP canister purge valve leaking (when canister is "clean").
• Fuel supply line restricted.
• Fuel rail pressure sensor (incorrect reading).

Air Induction System

• Air leaks after the MAF.
• Vacuum Leaks.
• PCV system (leak, valve stuck open, etc.)
• Improperly seated engine oil dipstick.

Exhaust System

• Exhaust leaks before or near the HO2Ss (exhaust manifold gasket, mating gaskets, etc.)..

EGR System

• EGR valve tube/gasket leak
• EVR solenoid vacuum leak

Secondary Air Injection

• Damaged/malfunctioning secondary air injection system (mechanically stuck valve).

View Freeze Frame Data to determine operating conditions when DTC was set. Observe LONGFT1 and 2 PID(s). Refer to Section 2 , Adaptive Fuel DTCs Diagnostic Techniques for more information.
P0457 - EVAP Control System Leak Detected (Fuel Filler Cap Loose/Off) A fuel tank pressure change less than a minus (-) 7 inches of H 2 0 in 30 seconds has occurred after refueling; or there is excessive purge (fuel vapor) flow greater than 0.06 pounds per minute.

• Fuel filler cap not installed on refueling (storing continuous memory DTC) and "Check Fuel Cap" light may also be illuminated.
• Fuel filler cap missing, loose or cross-threaded.

Check for missing fuel filler cap or integrity of the cap. If OK, clear continuous memory DTCs and re-initiate EVAP Emission Running Loss Monitor Drive Cycle.
Stuck open evap purge valve , maybe. Take your vehicle to a qualified repair shop an have the evap system smoke tested .

P1151 - Lack of HO2S-21 Switch, Sensor Indicates Lean A HEGO sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when fuel control system no longer detects switching for a calibrated amount of time. See Possible Causes for DTC P1130

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

A code p0455 most likely means one or more of the following has happened:

• A loose or improperly affixed gas cap
• A non-conforming gas cap (i.e. not factory/original brand)
• Other leak or damaged piece in EVAP system

With a p0455, the most common repair is to:

• Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
• Otherwise, replace the gas cap, and/or
• Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary