Rear view mirror mounting hole cover (17K709)

Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal

1. Disconnect battery ground cable (14301).
   

1. Remove front door trim panel (23942). Refer to Section 01-05.
   

1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
   

1. Remove two screws from cover assembly.
   

1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
   

1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.
   

Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal

1. Remove cover behind inside door handle.
   

1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
   

1. Remove three screws retaining front door trim panel to front door.
   

1. NOTE: Do not attempt to remove more than one pushpin at a time.
   
   Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
   

1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
   

Installation

1. Follow removal procedure in reverse order.
   

1. Replace all pushpins with new pushpins (N808994-S).
   

Front Door Trim Panel

Hello, to replace the rear mirror, try the following:

1. Roll the passenger side door window all the way down. Turn off the ignition and remove the keys.


2. Gently pry the window control panel from the arm rest with the pry tool or screwdriver starting at the bottom of the panel. Flip it over and unplug all the wire harness outlets from it. Set the panel aside.

3. Locate and remove the two panel door plugs near the arm rest concealing the two screws and remove the screws with the Phillips head screwdriver.

4. Remove the door panel retainer plugs along the edge of the door by pressing in the middle of the plug to unlock it and removing the plug.


5. Detach the mounting triangle from the upper inside door panel covering the side-view mirror.

6. Remove the door panel by lifting outward and then upward. Disconnect the speaker wire harness from the underside of the door panel and set the door panel aside.

7. Locate and disconnect the mirror wire harness.

8. Pull back the foam insulation from the inside panel covering the side-view mirror.

9. Unscrew the three mounting nuts from the mirror using the ratchet, extension and a socket. Do not drop the nuts into the door cavity.

10. Pry the mirror gently away from the outside of the door.

11. Install the new mirror and replace the mounting nuts on the mirror studs and tighten with the ratchet, socket, and extension. Plug the mirror wire harness back in. Replace the foam insulation. Replace the mounting triangle.


12. Replace the door panel by reversing the procedure. Start by plugging in the speaker wire first.


Thanks

look under the covers and their is either a screw or a bolt that will tighten the spring loaded cups

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

Remove the Old Mirror
1. Step 1 Disconnect the negative battery cable before you take off the grand Cherokee front door trim panel. Remove all screws and clips.
   
2. Step 2 Detachthe window trim cover screw, and control lever screw beforedisconnecting the entire mirror trim cover. Remove the rubber coverinside the mirror cover, and disconnect the electrical wire.
   
3. Step 3 Remove three nuts from the power mirror using a Torx® star-shaped screwdriver.
   
4. Step 4 Pull out the outside rear view mirror. Guide the power wire through the hole in the door.
   
Install the New Mirror
5. Step 1 Replace the old mirror. Put the new power mirror in place. Push the new wiring through the hole in the door.
   
6. Step 2 Install and tighten the three retaining screws you took off when removing the old mirror.
   
7. Step 3 Connect the power mirror wiring to the connection located on the door panel. Replace the rubber cover and interior mirror cover.
   
8. Step 4 Put the front door trim panel back in place by securing all clips and tightening all screws.
   
9. Step 5 Connect the Subaru Outback's battery cable to restore the power.
   

i will recommend i site where you will get all the information you need to remove and replace your side mirror
http://www.wjjeeps.com/mirrors.htm

front

SECTION 501-05: Interior Trim and Ornamentation 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Trim Panel —Front Door Removal

1. Remove the rear view mirror mounting hole cover (17K709).

1. If equipped, remove the window regulator handle (23342); refer to Section 501-11 .

1. If equipped, remove the window regulator switch plate (14524); refer to Section 501-11 .

1. If equipped, disconnect the power windows, power door lock switch and power mirror connectors.

1. If equipped, remove the front door trim panel reflector or the courtesy lamp lens.

1. Remove the screws.

1. NOTE: Remove the front door trim panel (23942) by pulling it straight upward.
   Lift and remove the front door trim panel.

1. If equipped, twist the courtesy lamp connector one half turn and remove it from the front door trim panel.

1. Remove the front door trim panel (23942) ; refer to Section 501-05 .
   • Peel back the watershield.

1. Remove the rear view mirror mounting hole cover (17K709).

1. Disconnect the power mirror electrical connector.

1. Remove the outside rear view mirror (17682).
   1. Remove the screws.
   1. Remove the outside rear view mirror.

please rate as fixya if this works for you.

I need a complete passenger Side Mirror (2nd Hand) N-95 (S Reg) contact 07966 366195

Gently tap the base of the mount upwards. I just replaced mine and I thought there was a cover over the winshield mount, turns out it is just pushed on to the wedge that is mounted to the windshield. Good Luck, webree