Where is the engine no located - Cars & Trucks

Freeze plugs, also known as expansion plugs or engine block heaters, are designed to expand and contract along with the engine block as it heats up and cools down. They are located in the engine block and are used to prevent the engine block from cracking due to the expansion and contraction of the metal.
In a 2008 Chevrolet Silverado 2500HD with a 6.0L engine, the freeze plugs are located in the following locations:

• Two freeze plugs are located on the back side of the engine block, near the top.
• Two freeze plugs are located on the bottom side of the engine block, near the front.
• Two freeze plugs are located on the passenger side of the engine block, near the bottom.

Here is a diagram showing the locations of the freeze plugs in a 6.0L engine:
[Insert Image]
I hope this helps! Let me know if you have any other questions.

Here is a general guide to the layout of the engine compartment of a 1994 2.0 liter engine: Battery: The battery is typically located on the driver's side of the engine compartment, near the front of the vehicle. Engine: The engine is located in the center of the engine compartment. Radiator: The radiator is typically located at the front of the engine compartment, behind the grille. Coolant reservoir: The coolant reservoir is usually located on the passenger side of the engine compartment, near the front of the vehicle. Fuse box: The fuse box is typically located on the driver's side of the engine compartment, near the front of the vehicle. Air filter: The air filter is typically located on the driver's side of the engine compartment, near the front of the vehicle. Throttle body: The throttle body is typically located at the front of the engine, near the top. Engine oil filter: The engine oil filter is typically located on the passenger side of the engine, near the bottom. Distributor: The distributor is typically located at the top of the engine, near the front. Engine oil dipstick: The engine oil dipstick is typically located on the passenger side of the engine, near the front.

The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

THE 2.4L ENGINE CMP SENSOR LOCATED REAR OF THE ENGINE CYLINDER HEAD. FOR THE 3.5L ENGINE CMP SENSOR LOCATED BEHIND TOP OF TIMING COVER IN FRONT OF THE INTAKE MANIFOLD. FOR THE 3.6L ENGINE HAS 4 CMP SENSORS LOCATED TWO ON EACH CYLINDER HEAD. FOR THE 3.9L ENGINE CMP SENSOR LOCATED IS LOCATED ON THE FRONT OF THE ENGINE ABOVE THE CRANKSHAFT PULLEY BELOW THE POWER STEERING PUMP PULLEY.

4.7L ENGINE CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK ABOVE THE STARTER. ON THE 4.0L ENGINE CRANKSHAFT SENSOR LOCATED TRANSMISSION BELL HOUSING AT THE LEFT REAR OF THE ENGINE. THE 5.2L 5.9L CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

This car comes with two diffrent engines, you didnt list the engine size so i will give you diagrams with the location for both engines, hope this is helpful, the 3.8 engine the sensor is located on the top right of the intake manifold, and the other engine is located on top left rear of engine below throttle body, heres are the diagrams and i labeled them good luck,

I don't see the knock sensor on the 4.0L engine. --- COMPONENT LOCATIONS Fig. 1: Electronic engine control component locations - 2.5L engine shown
Fig. 2: Overhead view of the (A) automatic idle speed motor, (B) MAP sensor, (C) crankshaft position sensor wiring harness, (D) air temperature sensor, and (E) throttle position sensor - 1992 Cherokee with the 4.0L engine shown
Fig. 3: Electronic engine control component locations - 4.0L engine shown
Fig. 4: Electronic engine control component locations - 5.2L and 5.9L engines (Part 1 of 2)
Fig. 5: Electronic engine control component locations - 5.2L and 5.9L engines (Part 2 of 2)

Here's a copy of component locations for various engine sizes for the 1996 Pontiac Grand Am that I had on my online resource. COMPONENT LOCATIONS The component locations shown are typical, and may vary slightly from one model year to another, because of variances in manufacturing and assembly. Fig. 2: 2.0L Engine Component Locations
Fig. 3: 2.3L Engine Component Locations — 1988–90
Fig. 4: 2.3L Engine Component Locations — 1991–93
Fig. 5: 2.3L Engine Component Locations — 1994–95
Fig. 6: 2.5L Engine Component Locations
Fig. 7: 3.1L Engine Component Locations
Fig. 8: 3.3L Engine Component Locations

On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.


Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines



Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

where it the crank potision sensor on a 92 mitsubishi diamante