Question about Cars & Trucks

1 Answer

I replaced the master cylinder for my 91 s10 now the clutch won't spring back how do I fix this

Posted by on

  • Johnny H Tidwell Apr 11, 2016

    It has fluid all the way to the slave cylinder but clutch still won't spring back should I just keep bleeding it or do I need to gravity bleed it anyway

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 56 Answers

What master CLY did you replace clutch or brakes you have air in the slave CLY for the clutch system and you will have to bleed the system and make sure you don't run low on brake fluid while you are bleeding the system.

Posted on Apr 12, 2016

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 3 Answers

SOURCE: clutch pedal stays down

Still have air in system.. Try this: Pull pedal up,fill reservoir to the top, open bleed nipple on slave cyl all the way,leave for a while to "gravity feed" keeping the reservoir full,& an eye on the nipple, until all bubbles are expelled and clean brakefluid drips out(could take a few minutes). Close the nipple, and bleed system as usual....

Posted on Jun 24, 2008

autodr

autodr

  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

Anonymous

  • 17 Answers

SOURCE: Clutch master cylinder replacement

yes

Posted on Feb 23, 2009

Anonymous

  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

tuyen bui

  • 1025 Answers

SOURCE: every time I bleed my clutch line on my 1998 chevy

there should be two bolts/nut that hold the master cylinder.
look under the dash on top of the clutch pedal

Posted on Feb 28, 2010

Testimonial: "kih"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The clutch on my 2006 pontiac solstice feels like the clutch cable has broken. i dont even know if it has one, or what the equivalent would be. the tension feels the same, but pushing the pedal does...


The tension you are feeling is probably the pedal spring under the dash to pull the cable back.. Open the bonnet and if you see a cable in the fire wall where the clutch pedal the you have a cable operation and it will need replacing. If you see a master cylinder next to the brake master cylinder then you have hydraulic system and it have to be bled or the master cylinder replaced Talk to a reputable service shop to have it fixed.

Oct 27, 2013 | Pontiac Solstice Cars & Trucks

1 Answer

I have a 1990 Chevrolet s10 s14 s15. 4x4 4.3 v6 Tahoe engine ext cab 5 speed. Anyways I recently replaced the clutch, throw out bearing, clutch fork, slave cylinder and master cylinder and 3 weeks later...


Linkage on the trans needs adjusting to engage center fork link when springs are centered. Remove the boot over the shifter linkage to check adjustment.

Aug 05, 2017 | Cars & Trucks

2 Answers

Fixed a master cylinder and slave cylinder on 2000 s10 pickup now i have no pressure on clutch what is the problem


The air needs to be bled out of system. Should have a "bleeder" on the slave cylinder resevoir. Fill 1st and open bleeder screw. Have someone push clutch pedal down and close bleeder when pedal is fully depressed. Do not pump pedal. Repeat until a steady stream of fluid is achieved. REMEMBER TO WATCH RESEVOIR LEVEL AND KEEP FULL DURING THIS PROCESS!!!! Top off when finished bleeding. This should fix your issue.

Apr 01, 2013 | Cars & Trucks

2 Answers

I just replaced the clutch, pressure plate, throwout bearing and both the master and slave cylinders. I am not getting any significant travel in the slave when I push the pedal in. How much travel should...


you may just open the bleeder, and let it gravity bleed. make sure on the master cylinder that the piston is coming all the way back when the pedal is all the way back/up. there's an adjustment for that, on the rod connecting the clutch pedal to the master cylinder.

Dec 21, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

Clutch pedal does not disengage clutch in '91 Chevy pickup. Changed Master Cylinder, slave cylinder, and bled hydraulic line. Still not disengaging clutch.Maybe throwout bearing stuck? Or clutch fork?


If the car hasn't been driven for a while it could be corrosion on the fork but I think that is unlikely. I think you are right about the release bearing being jammed in the spring. If the truck has quite high mileage, it probably means a clutch job.

Feb 27, 2010 | 1991 Chevrolet C1500

3 Answers

Clutch fluid weight 1988 chevy s10


in the trans is 80w-90. the clutch fluid is actally the exact same as dot3 brake fluid.

Dec 05, 2009 | 1988 Chevrolet S-10

1 Answer

My clutch pedal wont spring back once i've released it. I've replaced the clutch, clutch fork & clips, throw-out bearing, clutch master cylinder, and even a slave cylinder. On top of all that, i've...


A clutch pedal not springing back is almost always an indication that there is air in the system. Bleeding out a clutch is a tedious endeavor to say the least.
I suggest you open up the bleeder screw & gravity bleed the clutch.(This will take a long time as well!)

Nov 29, 2009 | Toyota Celica Cars & Trucks

3 Answers

Clutch


Stop driving the car now! The clutch master cylinder has an adjustable pushrod, it is set up too long now. Take it back to where it was done and tell them if they don't know how to set up clutch free play, they shouldn't have attempted the job. This may have cost you a $3500. clutch job. Get it adjusted fast.

May 05, 2009 | 1991 Porsche 944

2 Answers

'91 eagle talon tsi awd...gears grind


Sounds like you need a clutch.

Jan 17, 2009 | 1991 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...