The windshield washer line detached. How do you reattach it without removing the hood?

Broken at the hood?DO NOT use Ford parts.Best repair is ......go to a "upull parts lot" this is where you remove the car parts yourself,find an older Hyundai Accent 2003 2004 style and pull the windshield washer hood squirters and hoses off the hood.They will fit right on your 2010 Focus hood.Bonus.... they will never break apart like the plastic Ford ones.Just attach the Hyundai rubber hose onto your plastic feed line on your Focus on the passenger side.

you either have a clogged nozzle or a broken washer line from the first nozzle to the second. you may have to remove under-hood trim to access the hose/ line

Its a special part..available from a Ford dealer. Fitting it means taking off the old one, and carefully noting how to put a new one back!

If you have access to compressed air, pull off line at reservoir and detach from other side too. Blow air through line to dislodge blockage. Work your way up to nozzles on hood. Not really easy but works. Or replace all the lines. Or pull nozzles on hood off and clean thoroughly.

Hood light on ????? hood ajar light ! Could be the switch . But without testing this would be a guess . Do you know how to test automotive electrical circuit's ? Do you know anything about automotive electronic's ? BCM - body control modules ( computer ) The first diagnostic procedure would be to hook up a factory or a professional scanner an check for DTC'S - diagnostic trouble code's in the BCM .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A

Your best bet , take your vehicle to a qualified repair shop. Nothing you can do without knowledge an proper diagnostic equipment .

Windshield Washer Pump Removal & Installation To Remove:

1. Remove the air cleaner assembly.
2. Remove the bolts.
   
   
3. Position the pump and reservoir aside.
4. Disconnect the electrical connectors.
5. Disconnect the washer hose.
6. Remove the pump and reservoir.
7. Remove the washer pump.

WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.
NOTE: Windshield washer fluid should be collected in a container after the windshield washer hose is disconnected.
To Install:
WARNING
Windshield washer solution contains methanol which is poisonous. Observe all cautions and warnings indicated on label of washer solution container.

1. Install washer pump in reservoir.
2. Install washer pump reservoir assembly.
3. Connect washer hose.
4. Connect washer electrical connector.
5. Install air cleaner assembly.

---
The windshield wiper fluid pump is located in the tank which is not in the heater motor or defroster area in the dash.

The defroster/heat control door is located in the dash board area:

Air Door Actuators, Cables or Motors Removal & Installation Air Inlet Door Vacuum Control Motor To Remove:

1. Remove the instrument panel lower insulator cover.
2. Disconnect the vacuum connector.
3. Remove the control arm clip and the spring.
4. Remove the nuts and the air inlet door vacuum control motor.

Air inlet door vacuum motor mounting screws

To Install:

1. Install the vacuum motor on the mounting bracket.
2. Connect the control arm and spring.
3. Connect the vacuum hose to the vacuum motor.
4. Install the lower instrument panel lower cover.

Floor Defrost Door Vacuum Control Motor To Remove:

1. Disconnect the negative battery cable.
2. Remove the left lower dash insulator panel and disconnect the lamp.
3. Remove the two pin-type retainers and remove the fill panel.
4. Remove the DLC mounting screws.
5. Detach the vacuum line.
6. Remove the lighting module.
7. Remove the screws and the bracket.
8. Remove the floor/defrost door vacuum control motor.

Floor/Defrost vacuum motor mounting screws

To Install:

1. Connect the vacuum lines and install the floor/defrost vacuum motor.
2. Install the bracket and lighting control module.
3. Install the DLC bracket and mounting screws.
4. Install the fill panel.
5. Install the left lower dash insulator panel.
6. Connect the negative battery cable.

Panel Door Vacuum Control Motor To Remove:

1. Remove the instrument panel.
2. Reach through the door opening and remove the pin.
3. Disconnect the panel door vacuum control motor vacuum line.
4. Remove the screws and remove the panel door vacuum control motor.

To Install:

1. Install the panel door vacuum motor.
2. Connect the vacuum line to the panel door motor.
3. Reach through the opening and install the pin to the linkage.
4. Install the instrument panel.

Windshield Washer Motor REMOVAL & INSTALLATION 1987-95 Vehicles

1. Disconnect the negative battery cable.
2. Drain or siphon the washer solvent from the reservoir.
3. For 1987-91 vehicles, remove the brace.
4. Unfasten the reservoir screws.
5. Detach the electrical connectors and washer hose.
6. If necessary, remove the reservoir from the vehicle.
7. Remove the washer pump motor from the reservoir. Fig. 1: Location of the windshield washer fluid reservoir and pump - 1987-91 vehicles
   To install:
   
8. Install the washer pump motor on the reservoir. Make sure the pump is fully seated in the reservoir gasket.
9. Position the reservoir in the vehicle.
10. Attach the electrical connectors and washer hose.
11. Install the reservoir retaining screws.
12. Install the brace.
13. Fill the reservoir with washer solvent.
14. Connect the negative battery cable, then check for proper washer pump operation.

1996-99 Vehicles

1. Disconnect the negative battery cable.
2. Drain or siphon the washer solvent from the reservoir.
3. Detach the electrical connectors from the washer.
4. Disconnect the hose from the washer pump.
5. Loosen the nut at the bottom of the washer reservoir.
6. Unfasten the 2 nuts, then remove the washer solvent reservoir.
7. Remove the washer pump from the container.
8. If necessary, remove the solvent lever sensor switch from the washer solvent container. Fig. 2: Exploded view of the washer fluid reservoir, pump and level sensor
   To install:
   
9. Install the solvent level sensor switch in the washer solvent container. The tab on the solvent level sender switch must be lined up with the slot in the hole.
10. Install the washer pump into the reservoir, making sure the pump is pushed all the way into the container seal.
11. Install the washer solvent reservoir and secure with the 3 nuts. Tighten the nuts to 44 inch lbs. (5 Nm).
12. Attach the electrical connectors to the solvent level sensor and washer pump.
13. Connect the hose to the washer pump.
14. Fill the reservoir with washer solvent.
15. Connect the negative battery cable, then check for proper washer pump operation.

it is connected to the bottom of the windshield washer reservoir... under the hood.

1992-98 Vehicles

1. Disconnect the negative battery cable.
2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
4. Detach the electrical connectors from the wiper motor.
5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
6. Unsnap and remove the linkage cover.
7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
9. Remove the motor retaining screws and remove the motor from the vehicle.
10. The installation is the reverse of the removal.

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip



Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from the vehicle






Fig.: Detach the electrical connector for the wiper motor

Release the wiper motor retaining clips and remove the cover from the vehicle






Fig.: Remove the wiper module assembly retaining bolts and remove the module from the vehicle






Fig.: Remove the wiper motor retaining bolts and ...





Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

According to the Haynes repair manual Chapter 12:

1. Disconnect the negative battery cable
2. Detach washer hoses, lift the wiper arm covers and mark the wiper arm locations on the pivot shaft for later re-installation. Remove the wiper pivot nut and remove the wiper arms.
3. Remove the cowl cover (from chapter 11)
3a. Remove the wiper arms then remove the screws that hold the lower area of the cowl cover to the wiper module.
3b. Disengage the quarter turn fasteners that hold the outer ends of the cowl cover to the wiper module.
3c. Open the hood and release the wing nuts that hold the front of the cowl cover to the wiper module.
3d. Close the hood but do not latch it. Now remove the outboard screws and lift the cover up enough to get to the washer hose.
3e. Disconnect the washer hose from the right washer nozzle. Close the hood but do not latch it. Lift the cowl cover toward the windshield and off the vehicle.
3f. Installation is the reverse of removal
4.Open the hood. Disconnect the wiper motor electrical connector.
5. Disconnect the windshield washer hose from the coupling inside the unit. Disconnect the drain tubes from the bottom of the wiper unit.
6. Remove the wiper unit mounting bolts. (Picture appears to be three (possibly allen head) bolts)
7. Remove wiper unit.
8. Installation is the reverse of removal. Wiper blade and wiper arm adjustment is measured with the wipers parked; correct adjustment is the lower wiper arm approximately 1.5 inches distance from the cowl cover and the upper arm approximately 2.5 inches from the lower arm. Operate the wiper motor and check that the wiper motor parks when the wiper switch is OFF.