When I start my car, it run's for a aproximately five minutes and then engine just shut off. What can be the problem?

Just because the CEL goes off does not mean codes are gone. Scan tool will show stored codes.

please post in english his is USA forum. and is english only.
here ill use google translate for you.
My truck Isuzu no longer running and turn off the computer turns my marks a po342 code that may be the position sensor of the tree cam d put it back and continued the same. which can be another.

Ok , P0342 is clear in the book, (but you never said engine type in car>? so......)
here are the possibles.
1: CMP sensor dead or bad.
2: cam timing way off. (is compression TEST over 150 PSI on all cylinders? (no engine stated, so.... cant tell you why see?
3: bad wiring to the CMP.
4: or CMP timed wrong.

CMP is the name of the CAM SENSOR. BTW.
no car stated.
no year stated.
no engine stated
no country, yes, cars do vary greatly by , COUNTRY.
mostly hopeless so for...


use google translate to translate ENglish back to Spanish.

to do so type, Translate in the google box and magic happens.

Did you do the key "Dance" for codes? Put key in ignition, turn to the "RUN" position - do not crank the engine - and return it back to the off position, do this four times, on the fifth time leave it in the "RUN" position and watch the check engine/power loss light and count the flashes. Should start with five flashes (start of test) followed by a couple series of flashes keep track of the number of flashes as this will tell you what sensor is on the fritz. The test is over when it flashes five times again. Also the chain stores will scan for zero cost.....Just for grins try unplugging the water temp sensor (usually near the thremostat) see if car stays running......Plug it back in to double check.

Could be a timing belt. P0342 Camshaft position sensor "a" circuit low input, Read all of the comments on the URL below.
Car silently stalls after startup and then won start back up Hyundai...

If you mean the check engine light is on when the engine is running, I would start there and have the computer scanned for trouble codes.
Without knowing what is shutting down it will be tough to troubleshoot.
Could be a relay or coil or any number of other things.
If there are no codes in the computer, I would look for a failing relay. A sensor should set a code.

Lets start with what is cel? CEL stands for Check Engine Light.

It is true that you can disconnect battery for 5 minutes to shut light off but you still have a problem, When ever the engine light blinks it is telling you some thing is wrong and is causing cataylic converter damage, the only time the light will bling is when the engine is misfiring and dumping gas into converter.

You will need to have the problem fixed or damage will occur and light will come back on.
Go to an auto parts store, like an auto zone and have them scan the computer for the stored codes, if you can get me the codes i will help you solve the problem, i would bet the code or codes will be po 300 codes, but get the codes.
Also i will need to know what year,make and model car you have with the engine size, good day

Lookfor a light on the dash that says SECURITY or ANTITHEFT. If you see this light, that is a sign of a failed or failing antitheft system, which will disable your vehicle. This link explains

http://vatspasslockpasskeysecurityhelp.yolasite.com/

First, if it is running that bad with the spitting and sputtering and all, the Check Engine light has GOT to be SCREAMING at you! If so, then that would be the first step. Get your engine computer scanned to find out why the Check Engine light is on.
If the Check Engine light is for some odd reason, not getting involved in this, I would still start with a scan and then watch the data stream to see what is going away to make the engine act the way it is. It sounds like you probably have a bad Crankshaft Position Sensor, but I would not go out and buy a new one before checking for other possibilities.

Please also review this article: What Else Could Be Wrong?

your check engine light will give you information that will help solve the problem-get the computer scanned, go to a retail auto parts store, they all do it for nothing. Write down the actual codes, and come back here with the codes, you will get the help you need.

you need to have car scanned for codes and it sounds like it is due for a major service