Question about 2003 Chevrolet Silverado 3500

1 Answer

IF crank sensor is unpluged will engine start

I just found the plug and it was not pluged in and my truck turns over but wont start

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 57 Answers

No! If the crank sensor fails the engine will not start. The ignition module must receive a crank sensor signal for the engine to run.

Posted on Mar 06, 2016

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Changed alternator turns over still wont crank


Check some fuses or see if you are getting any kind of spark. Spark at the plugs or injectors.

Apr 14, 2015 | 2004 Dodge Stratus

1 Answer

My 1999 2.4 dodge stratus wont run unless i unplug cam sensor its a new sensor and a new crank sensor


I'm having excatly same problem, found this sequence to ge the car running again..turn off ign, unplug cam position sensor, crank for 2 seconds, connect cam shaft sensor, crank again and it starts like that...

Apr 01, 2011 | 1999 Dodge Stratus

3 Answers

2005 gmc safari wont start checked coil spark


how much fuel pressure you have when turn key on

Feb 04, 2010 | 2005 GMC Safari

2 Answers

Went through flood water now engine want start


ALl Spark PLUGE MUST be REMOVED and With them OUT CRANK Engine to Blow OUT ALL WATER or it WILL HYDRO-LOCK and DEMOLISH the ENGINE

Dec 22, 2009 | 1994 Oldsmobile 88

1 Answer

1992 Ford Taurus wagon not starting, but turns over


You might have a problem with your crank sensor or ignition. Remove spark plug wire and check for spark while turning engine over. When this happens unplug crank sensor near crank pulley then plug back in to see if it starts if so replace crank sensor.

Jul 29, 2009 | 1992 Ford Taurus

2 Answers

97 dodge neon died replaced parts and still no spark HELP.


YOU NEED TO CHECK DARK GREEN/ORANGE WIRE AT IGNITION COIL WHEN CRANKING ENGINE FOR POWER..IF NO POWER,SHUTDOWN RELAY IS NOT BEING ENERGIZED..THIS ENGINE ALSO HAS CAMSHAFT POSITION SENSOR ON END OF CYLINDER HEAD..ENGINE CONTROLLER NEEDS CAM AND CRANK SIGNALS TO ENERGIZE THE SHUTDOWN RELAY..UNPLUG CRANK SENSOR AND CHECK VOLTAGE ON ORANGE WIRE..SHOULD HAVE APPROX 8V..IF NOT..UNPLUG CAM SENSOR AND SEE IF 8V SUPPLY RETURNS..IF NO POWER TRY UNPLUGGING VEHICLE SPEED SENSOR LOCATED IN TRANS HOUSING WHERE RIGHT SIDE AXLE COMES OUT OF TRANS..IF 8V RETURNS..THE SPEED SENSOR IS SHORTED INTERNALLY..THESE 3 SENSORS SHARE THE SAME 8V SUPPLY CIRCUIT..WITH SPEED SENSOR UNPLUGGED,PLUG CRANK SENSOR BACK IN AND TRY TO START ENGINE..HAVE SEEN THIS SAME PROBLEM AT WORK RECENTLY

Jul 18, 2009 | 1997 Dodge Neon

1 Answer

Wont start No buss on speedometer.


Disconnect the crankshaft position sensor and turn the key on. See if the "no bus" message goes away and the gauges come back to life. If so, replace the crankshaft position sensor. On a 4.7 it is just above the starter, on a 4.0 it is on the left side of center of the bell housing. The modules all communicate on the bus and if it is down the vehicle won't start. I've seen the crank sensor short out and pull the bus down resulting in the exact condition you described.

Jun 06, 2009 | 2000 Jeep Cherokee

1 Answer

Car wont start


No spark, ck the crank position sensor. bolted on engine at the front crank pully. Good luck. unplug and plug it back in to clean the wire connection/

Jun 03, 2009 | 1990 Dodge Dynasty

2 Answers

Car wont crank 1994 plymouth acclaim


Not sure what yor experiencing . Do you have crank no start or no crank no start? No crank no start is battery and cables issue. Crank no start is ignition , plugs, and fuel.

May 28, 2009 | 1991 Plymouth Acclaim

2 Answers

Flat at acceleration, wont idle


Check the fuel filter to make sure it is not pluged up, also check fuel presure, if its ok you possibly have a pluged cat. converter.

Nov 26, 2008 | 1990 Chevrolet S-10 Blazer

Not finding what you are looking for?
2003 Chevrolet Silverado 3500 Logo

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...