Location of egr valve - 2006 Cadillac DTS

Question edited for clarity.
Question moved to model category.

3.9L EGR valve location

Dakota Durango Forum https://www.dakota-durango.com > threads > 3-9l-egr-...
OBD-II trucks (96 and up) didn't have EGR any longer. If it did it would have a tube coming off the passenger side exhaust manafold and running to the EGR valve ...

2000 dodge dakota egr valve location

Fixya https://www.fixya.com > ... > Cars & Trucks > Dodge
4 hours ago - On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the ...

SOLVED: Where is egr valve on 2000 dodge durango - Fixya
Oct 26, 2008
Where is the EGR valve located on a dodge durango - Fixya
Feb 5, 2009
How to reach the EGR valve on a 2000 dodge durango - Fixya
Oct 15, 2015
Where is the location of the egr valve on the 4.7 liter engine
Nov 17, 2019
More results from www.fixya.com

https://www.google.com/search?source=hp&ei=Lv7CWeTpHKec0gK2kJnQBA&q=egr+valve+gasket+location+2004+kia+rio+cinco+&oq=egr+valve+gasket+location+2004+kia+rio+cinco+&gs_l=mobile-gws-hp.3...1495.32570.0.33339.45.45.0.10.10.0.294.9684.0j8j36.45.0....0...1.1j4.64.mobile-gws-hp..2.38.6486.1..0j41j0i131k1j0i131i46k1j46i131k1j0i22i30k1j33i22i29i30k1j33i160k1j33i21k1.185.BNVxrxB9EO8

I don't have a good picture of coolant temp sensor location? My info just said close to egr valve, so, I posted egr valve location. The egr is close to throttle body in the picture. The coolant sensor has two wire connector, yellow and pink. I tried to help?

this is what the EGR looks like, usually near the back of the intake manifold on carbureted vehicles. check the vacuum at the hose before changing the EGR, your vac hose may be leaking instead of a faulty EGR. cost a dollar for vac hose.

An EGR valve assembly located at the front of the intake manifold. The EGR valve is a poppet style valve (on/off only) and is controlled by an internal diaphragm.



Fig. EGR location and associated components-California diesel

Hope helps (remember to rate this and comment ).

EGR VALVE IS #2.

Please wait for second post to answer your second question....comes with a few pictures.

yes the passages can be cleaned. They pass exhaust gas into the intake maniflod for reburning.

It could be the DPFE that controls the EGR too. Diff. Pressure Feedback EGR.

there is also a vacuum regulator valve and a solenoid too.

Please rate as fixya if this helps.

----------------
Exhaust Gas Recirculation (EGR) Valve —3.0L (2V) Removal and Installation

1. Disconnect the exhaust gas recirculation (EGR) valve (9D475).
   1. Disconnect the vacuum line.
   1. Disconnect EGR tube nut.

1. Remove the EGR valve.
   • Remove the two bolts.
   • Remove and discard the gasket.

1. NOTE: The sealing surfaces are soft metal.
   To install, reverse the removal procedure.
   • Carefully clean both sealing surfaces and install a new EGR valve gasket.

--------------------------------------
EGR Valve —3.0L (4V) Removal and Installation

1. Remove the EGR valve (9D475).
   1. Disconnect the vacuum line.
   1. Disconnect the EGR tube.
   1. Remove the EGR valve and discard the gaskets.

1. NOTE: The EGR valve sealing surfaces are soft metal.
   To install, reverse the removal procedure.
   • Carefully clean all sealing surfaces and install new EGR valve gaskets.

The EGR Valve Location is typically housed on the intake manifold this schematic may help you
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008822d

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.