At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
That is the code for the fuel temp sensor. The sensor is located on the fuel pump and it is available seperately. You have to remove the fuel pump to get to it.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
No . With the check engine light on there is probably a DTC diagnostic trouble code stored in the computer . Have code read ,diagnose and repair problem . Suggest you take your vehicle to a qualified repair shop and have if fixed right .
Code 440 is for a general failure of the EVAP system which is the vent system for the gas tank.
The engine computer checks the system every few minutes and if it detects a leak the check engine light comes on. The light tells the driver there is a problem and to get it checked out.
You would need a shop manual to get all of the testing procedures for the system and you would need to check for leaks.
P1095 Mass air flow ahead of throttle valve implausible (too high) Possible fault causes: - Hot-film mass air flow meter faulty (battered) - DME control module faulty (ambient pressure sensor at fault detection threshold)
code p 0180 refers to fuel temperature sensor A--circuit malfunction====causes wiring---fuel temperature sensor---ECM
it will most likely be the fuel temp sensor so call the dealer spares to get a price of that part ,then contact a reputable spares shop and see if there is a generic sensor that would be cheaper
the cost to fit will depend on the degree of difficulty and the shop doing the job
O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.--------
Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors . ---------------For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- ---------You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- --------------The codes which you get is scanning will be mostly any of this following codes:---DTC P0500 - Vehicle Speed Sensor Malfunction . DTC P0750 - Shift Solenoid "A" Malfunction . DTC P0753 - Shift Solenoid "A" Electrical Malfunction . DTC P0755 - Shift Solenoid "B" Malfunction . DTC P0758 - Shift Solenoid "B" Electrical Malfunction . DTC P0770 - Shift Solenoid "E" (SL) Malfunction . DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction . DTC P1520 - Stop Light Switch Signal Malfunction . DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction . DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction . DTC P1780 - Park/Neutral Position Switch Malfunction---------------Now it all depends on what code you get, as per that you can replace the following part.-------This will help.Thanks.Helpmech.
Whenever the 'CHECK ENGINE' light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on. At least there is 'FREEZE-FRAME' data stored and the associated DTC.
×