At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The remote keyless entry (RKE) module for a 2010 Volvo S80 V6 is typically located in the trunk of the vehicle, near the spare tire. It is a small module that is responsible for controlling the functions of the remote keyless entry system, such as locking and unlocking the doors, activating the alarm, and starting the engine using the remote.
To locate the RKE module, you may need to remove the trim panel or carpeting in the trunk. If you are unable to find the module or are unsure of its location, you may want to consult your owner's manual or a repair manual for your specific model of Volvo S80. Alternatively, you can try contacting a Volvo dealership or a mechanic for assistance.
no code for that, may show misfire on plug or cyclinder ,fuel system problem. pull one wire at a time put on plug edge listen for pop. hear pop coil is firing. no pop bad wire or coil or power to coil
Ignition module doesn't go bad often. If you are not getting spark I would check crank sensor first, they do fail often. If you have spark check fuel pump relay. That's another item that fails frequently.
1) Faulty coil, connections to coil, or other secondary wire issues, cap/rotor defective 2) Faulty switching node (this is the Bosch "ignition amplifier module" on the driver's fenderwell, front. 3) Faulty crank angle sensor or connector 4) Rare, faulty ignition computer
Notes on the coil: Positive is a fused feed. Verify you have 12 VDC at this point with the coil disconnected and reference this to ground with KOEO (KP II). The 'ground' circuit is switched by the aforementioned ignition amplifier on the driver's fenderwell which is switched by the ignition module.
Crank angle sensor must be functioning for ignition system to work. If this is faulty, the entire system shuts down. This is located at the top of the bellhousing, rear of engine. Take care upon removal or installation, the bracket is fragile.
You either have a bad ignition coil or the ignition module.What you can do is swap the 2 coils to see if the misfire changes cylinders.If it does then it is the coil if not then it is the module.The module is located under the coils.Hope this helps.Good luck.Let me know if you have anymore questions.
the ignition module is to the left of the air filter, right against the right side of the engine. I replaced mine, just two screws and take off black plastic covering. Make sure u disconnect negative battery post first. When done hook negative back up. If engine light don"t go off for P0320 code, disconnect battery for 5 min and connect back, I let my battery stay disconnect overnight.
the P0303 code is for cyclinder #3 possible causes:
-defective spark plugs, ignition cables, ignition coil. or flywheel/pulse wheel.
-blocked/leaking injector
-uneven compression
-leakage between the cooling system and cyclimder
moisture,flashover in the ignition system on HT side
intermittent open-circuit, intermittent short circuit to tje ground,intermittent short circuit to the voltage supply, contact resistance or loose connector in the ignition system low-tension side, in the injector circuit or fuel pump circuit
-fuel stoppage
-water in the sparl plug wells
- contaminated fuel or incorrect fuel type
-repeated cold starting where the engine coolant temperature (ECT) has not reached nomal operating temperature between start
P0304 is for cyclinder #4.
Hope this can help you, please put some rating
×