SOURCE: HOW TO YOU GET AT PRESSURE SENSOR ON COMMON RAIL HYUNDAI SANTA FE 2007 CDX
This is what it looks like
SOURCE: 2007 Hyundai Santa Fe - Replacing fog light
hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?
SOURCE: How to program keyless remote
I just had to buy one too and these are the instructions I was given by the guy I bought it from. I haven't tried them yet. Hopefully they work for us both :).
1.Find the ETACS unit under the steering wheel first,there is a small switch onit.
2.Once the switch is located make sure your key is not in the ignition and set the switch from off to set.
3.Press keyfobs door lock button for one second, this sends the codes to the ETACS and stores it.
4.Do the same thing if you have 2 remotes for the vehile.
5.Now set the ETACS switch from set to off.
6.Remotes should now be programed.
SOURCE: 2007 Hyundai Santa Fe Limited
Hey all,
I was able to get installation instructions for the cross bars from http://www.capitolhyundai.com and from http://dealerfit.com. Thanks much to these folks for providing a pdf of these instructions free of charge!
Below is the text from the instruction set that worked best for me. The other instruction set was nearly identical but it had an alternate Step 2 which involved using a small plastic pry bar. I added that alternate Step below in the instruction step. Hopefully I'm able to insert the image of each instruction set so that the Figures are visible. Its actually not that easy getting the rear rail covers off and its pretty easy to crack them. I'd recommend gently rocking the covers for a couple minutes in order to loosen them up. Once you get the covers off, the rest of the install is a breeze and can be done in 2 minutes. If you have questions, go ahead and contact me. I also took several photos of my install and that might be helpul. Cheers!
-LePig
-----------------------------------------------------------------------
SANTA FE 2008
PIN U8210-28000
Cross Bar Assembly Installation Procedures
Kit Contents:
• (2) Cross Bar Assemblies
Required Tools:
• Flat Head Screwdriver
INSTALLATION INSTRUCTIONS
1. Carefully unscrew and remove radio antenna.
2. Grasp the rear rail covers with both hands. Squeeze and pull up &
inwards (toward the center of the vehicle) to remove covers. Take
care not to break off the tabs by lifting the rear section of the cover
first (Figure 1). Be careful not to scratch, damage or dent any painted
surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS
CAN CAUSE DAMAGE TO THE VEHICLE.
2. - Alternate Method - Locate notch in rear of each cover to insert
plastic pry bar. Remove cover by prying up (with
tool) and lifting rear at 45 degree angle (Fig 1).
Be careful not to scratch, damage or dent any painted
surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS
CAN CAUSE DAMAGE TO THE VEHICLE.
3. Check assembly clips for damage and dislocation.
Replace if necessary.
4. Open the lever on one side of front/rear cross bar. Gently set the
cross bar, with the arrows facing forward, into the channel of the
side rails (Figure 2). Guide both sides into the track.
5. To adjust cross bars, open lever and place cross bars in desired
location. Close lever (Figure 3). Try to move bars forward/back
until they lock into place.
6. Reinstall rear covers by holding cover at a 45 degree angle and
inserting the front tab into the rear of the roof rack. After aligning,
snap cover in place (Figure 4). Be sure that the rubber lip does not
interfere with the covers, and that the covers are fully seated.
7. Reinstall the radio antenna.
Note: To remove the cross bars, remove the antenna, remove the
covers, open lever of cross bar and slide to end of rail. Hold
down locking fingers (on both RH/LH rear rail supports) with
a flat head screwdriver (Figure 5). This will allow removal of
cross bars from the rails.
SOURCE: PROGRAM KEYFOB FOR HYUNDAI SANTA FE
This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.
351 views
Usually answered in minutes!
×