What has to be done to eliminate recurrent DTC P1336?

Did you reset the code after the replacement?

Camshaft / Crankshaft Sensor is the reason for the code. They come in different qualities. OEM is best, made in Mexico is the worst!

PREVIEW
8:17 2002 Ford F150 - Codes P0340 and P1336: Cam Position ...
YouTube · Bent Oaks Garage Nov 30, 2021 PREVIEW
6:37 How to change Camshaft Position Sensor (CMP) - 2002 Ford ...
YouTube · Innova Feb 26, 2016 10 key moments in this video













PREVIEW
13:18 Ford 4.2 L Camshaft Position Synchronizer Replacement ...
YouTube · JamesonDIY Sept 8, 2019 10 key moments in this video













View all

P1336 2002 FORD F150 - Engine-Codes.com

https://www.engine-codes.com > p1336_2002_ford_f150
'P1336 2002 FORD F150 code possible causes · Faulty Crankshaft Position Sensor · Faulty Camshaft Position Sensor · Crankshaft Position Sensor harness is open or ...

If this DTC sets, there is a problem with the camshaft position actuator solenoid high control circuit shorted to voltage or the solenoid stuck open.
The PCM sends a pulse width modulated 12 volt signal to a (CMP) actuator solenoid in order to control the amount of engine oil flow to a cam phaser passage.
Do you know what a pulse width modulated signal is ?
Diagnostic Aids
Important: Scan tool control of the CMP actuator solenoid is inhibited when DTC P1345 sets.
The following conditions may cause this DTC to set:
• An improperly torqued harmonic balancer
• A mis-built or mis-timed engine
• A loose or missing crank damper bolt
• The camphaser solenoid stuck open
• The camphaser stuck in a position other than 0 degrees
• The camphaser does not return to 0 degrees within 16 seconds

Do you know what a diagnostic flow chart is ?

If this DTC sets, there is a problem with the camshaft position actuator solenoid high control circuit shorted to voltage or the solenoid stuck open.
Step
Action
Values
Yes
No
1
Did you perform the Diagnostic System Check-Engine Controls?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Engine Controls
2
Start the engine.
Clear the DTCs with a scan tool.
Does the scan tool indicate that DTC P0014 failed this ignition?
--
YES - Go to DTC P0014
NO - Go to Step 3
3
Observe the Freeze Frame/Failure Records for this DTC.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
--
YES - Go to Step 4
NO - Go to Diagnostic Aids
4
Turn OFF the ignition.
Inspect the crank damper bolt for the proper torque. Refer to Crankshaft Balancer Replacement in Engine Mechanical.
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 5
5
Disconnect the camshaft position actuator.
Remove the camshaft position (CMP) actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Replacement .
Jumper the camshaft position solenoid actuator high control circuit of the actuator solenoid assembly to 12 volts. Refer to Using Connector Test Adapters Wiring Systems.
Jumper the low reference circuit of the camshaft position actuator solenoid to a good ground. Refer to Using Connector Test Adapters in Wiring Systems.
Does the pintle inside the CMP actuator solenoid move?
YES - Go to Step 6
NO - Go to Step 8
6
Inspect the CMP actuator for binding or being stuck. Refer to Camshaft Position Actuator Diagnosis in Engine Mechanical.
Did you find and correct the condition?
--
YES - Go to Step 9
NO - Go to Step 7
7
Inspect the engine for correct valve timing. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical.
Did you find and correct the condition?
--
YES - Go to Step 9
NO - Go to Diagnostic Aids
8
Replace the camshaft position actuator solenoid. Refer to Camshaft Position Actuator Solenoid Valve Replacement .
Did you complete the replacement?
--
Go to Step 9
--
9
Clear the DTCs with a scan tool.
Turn OFF the ignition for 30 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
--
Go to Step 2
Go to Step 10
10
Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?
--
Go to Diagnostic Trouble Code (DTC) List
System OK

P1336 Ford P1336 Ford - Crankshaft Position Or Camshaft Position Sensor Input Signal Error Share
0 ' Add Comment Possible causes
- Faulty Crankshaft Position Sensor
- Faulty Camshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected a synchronization or signal error from the cam or crank sensors
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
- Engine difficult to start
P1336 Ford Description
The input signal to the powertrain control module (PCM) from the crankshaft position (CKP) sensor or the camshaft position (CMP) sensor is erratic.

Read more: http://www.engine-codes.com/p1336_ford.html#ixzz3qT9Hiztc

P1336 FORD Crankshaft Position Or Camshaft Position Sensor Input Signal Error

Here's what I've found about this P1336 code:
P1336 Crankshaft sensor is out of sync with camshaft sensor test
If you get this code, the first thing to check is your distributor especially if you have an imported vehicle. Look for signs of oil in the distributor which can contaminate the signals being monitored by the ECM (engine computer). Check also the wiring leading to the distributor and see if the wires are properly insulated away from hot exhaust which could burn the wires. Check also on the crank sensor location whether it is located in the front of the engine or at the flywheel at the rear of the engine. The same can be done for the cam sensor.
On engines with distributor, the cam sensor is usually located in the distributor and it will give you a lot of grief if not properly align and synchronize with the crank sensor. On some applications (like Ford), an alignment tool is required which is can be bought from your local parts store (cost about $31). If you install the distributor without proper timing, it will still run but the mileage will suffer and the above code showing up.
Your local trusted mechanic or Ford Dealer should be able to resolve this for you (if you can't) without too much trouble.

Do you have code P1336 and poor driveability (ie misfires, surging like the trans is drpopping in and out of overdrive). if so you may need to relearn the pcm?
Did you by any chance change the plugs and wires, did you also replace the coil? Also, did you bump or pull the connector for the camshaft postion sensor? Could be it's just coincodence and the sensor just went. Not 100% sure, but I beleive that the cam sensor is used in a sequential fuel injection system to tell the ECU when to turn on an individual fuel injector. If the ECU doesn't detect a signal from the cam sensor, it will default to a batch fire mode, where all 3 injectors on either side of the engine will fire simultaneously causing misfires?
If you can't reprogram the ecu replace the camshaft sensor.

The crankshaft position (CKP) system variation learn feature is used to calculate reference period errors caused by slight tolerance variations in the crankshaft, and the CKP sensors. The calculated error allows the powertrain control module (PCM) to accurately compensate for reference period variations. This enhances the ability of the PCM to detect misfire events over a wider range of engine speed and load.

The code P1336 is for a Crankshaft (CKP) and/or Camshaft (CMP) position sensor input signal to PCM concert. It is triggered if the input signal to the PCM for either of these sensors is erratic. Per the factory service manual, this can be due to:
- a damaged PCM
- damaged CKP sensor
- damaged CMP sensor
- base engine
- harness concerns.

The service manual suggests checking the following items:
- harness routings,
- alterations,
- improper shielding,
- or electrical interference from other improperly functioning systems.

To properly check the operation of the CMP and CKP, you'll really need an oscilloscope. The code is probably being triggered due to a faulty sensor or connection and not something that just needs to be reset.

Step / Action / Yes / No

1. Did you perform the Diagnostic System Check-Engine Controls?
Yes: Go to Step 2
No: Go to Diagnostic System Check - Engine Controls

2. Preform the CKP system variation learn procedure. Refer to CKP System Variation Learn Procedure. Did you complete the action?
Yes: Go to Step 3
No: Go to Diagnostic Aids

3. Clear the DTCs with a scan tool.
Turn OFF the ignition.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC run and pass?
Yes: Go to Step 4
No: Go to Step 2

4. With a scan tool observe the stored information, Capture Info.
Does the DTC run and pass?
Yes: Go to Diagnostic Trouble Code (DTC) List
No: System OK


Diagnostic Aids:
The CKP system variation values are not stored in the PCM memory after a learn procedure has been performed. If the actual CKP variation is not within the CKP system variation compensating values stored in the PCM, DTC P0300 may set.

The CKP system variation learn procedure is also required when the following service procedures have been performed, regardless of whether DTC P1336 is set.
An engine replacement
A PCM replacement
A harmonic balancer replacement
A crankshaft replacement
Any engine repairs which disturb the CKP sensor relationship

If the CKP system variation learn procedure cannot be performed successfully, check for the following conditions and correct as necessary:
A damaged reluctor wheel
Excessive crankshaft runout
A damaged crankshaft
Interference in the signal circuit of the CKP sensor
A coolant temperature that is not within the Conditions For Running the DTC
The ignition switch is in the ON position until the battery is drained
A PCM power disconnect with the ignition ON may erase the stored value and set the DTC P1336

Hope helps.

Do you have a running problem or just a check engine light?

Here's the diagnostic procedure for DTC code 0340, directly from the service manual:

I would think it would be just the Camshaft Position Sensor.I looked up the codes and they say pretty much the samething.


P0340 Ford Camshaft Position Sensor Circuit Malfunction


P1336 Ford Crankshaft/Camshaft Sensor Range/Performance