Question about 2000 Ford Focus

1 Answer

5-speed. How do I replace clutch and pressure plate?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Remove transmission .do research find out what all tools needed.and type of fluid. make sure to have car stable and safe while under.might have to remove more than just the trans depends on car.make sure to place throw out bearing correctly seated in place are you would have done it all for nothing. cheak and make sure you have fluid in the container .break fluid will work just might be out of fluid.youtube has alot of vids

Posted on Dec 27, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does the clutch slip intermittently on my Audi A4 2009 Diesel in high gears


Agreed. The clutch disk is likely worn. The pressure plate is self adjusting so there is no adjustment available on stock Audi pressure plates or indeed in most pressure plates.

Another possible cause is a leaking rear main engine seal that is allowing engine oil to seep and then be thrown around the bell housing and work its way onto the flywheel/clutch/pressure plate.

Test you clutch in 3-4 gear acceleration from a slow speed...if the engine speed flares faster than the car accelerates, you have a worn/bad clutch.

Mar 22, 2015 | 2004 Audi A4

2 Answers

Hyundai. Tucson, 59 plate' clutch slips at high speed when changing gear


check /replace clutch cable or replace master cylinder. If the clutch has not been replaced it may need a clutch kit as the indications are that the pressure plate is weak ( worn clutch plate or from overheated clutch)

Feb 10, 2015 | Hyundai Tucson Cars & Trucks

1 Answer

Car won t move in any gear


Did you also replace the pressure plate? Pilot bearing? If you replaced the clutch...and the car moved, and then stopped moving again...your issue is likely right there, bad pressure plate, flywheel may need resurfaced or replaced ETC. I am curious to know what the old clutch disc looked like when you took it out. Was it glazed or worn? I would pull the tranny again, and look at the new disc to see if it is glazed looking from slipping...and note if it is both sides, or one side, and which side...plate side or flywheel side. If you didn't replace the pressure plate/pilot bearing with the clutch disc...I would do that.

Mar 21, 2014 | Honda Cars & Trucks

1 Answer

Replace clutch


A new clutch kit or clutch package has 3 major parts: a new clutch disc (the thin plate with the abrasive surface), a new or reconditioned clutch pressure plate, and a new clutch release bearing (aka, throw-out bearing). Approximately $200 for the package.
Some people have been known to change only the clutch disc (for about $30), and use their old pressure plate and throw-out bearing. Not recommended-same people have been known to have to go back sooner than later to then replace the pressure plate and release bearing. Do it all once, then you won't have to go back and re-do it.

Have you checked the hydraulic clutch operation? Before condemning the clutch disc for failure, make sure the hydraulic clutch cylinder causes the clutch fork or lever to have sufficient travel to engage the clutch when the pedal is depressed. Also check the clutch fluid reservoir for being full.

Sep 18, 2013 | 2006 Kia Spectra

2 Answers

1998 Honda accord manual transmission revs high, car barely accelerates. What would cause this problem? the clutch was replaced 2 years ago.


You know the clutch is slipping
& continue to drive & ruin that

Now you can do another clutch
service, while your finding the answer
to what your asking

Next car get an automatic & just change
the fluid every 3 years

Mar 07, 2013 | Cars & Trucks

1 Answer

Engine speed increases with no increase to vehicle speed


If your car has a manual gear box thn the clutch plate may need replacing, if need be better to replace the pro-kit i.e clutch pressure plate , clutch plate and the relaese bearing.

Sep 21, 2010 | 1996 Volkswagen Jetta

1 Answer

5 speed hard time shifting and it has a new clutch.


Replacing the clutch plate only sometimes doesn't help you should have replaced the clutch pressure plate too, best is to fit the clutch pro-kit (clutch plate, clutch pressure plate and release bearing).
I guess now you will have to just replace the clutch pressure plate and the release bearing.

Nov 23, 2009 | 2000 Kia Sportage

2 Answers

CLUTCH SLIPS, ENGINE SPEED INCREASES BUT ROAD SPEED DOES NOT INCREASE. WHAT COULD THE PROBLEM BE? HAVE JUST REPLACED THE CLUTCH PLATE, CLUTCH SLAVE CYLINDER AND THE PRESSURE PLATE. PRIOR TO THIS THE GEARS...


If yhe clutch is slipping there is not enough free playand you are not fully engaging. You should have a quarter to half in play before you feel resistance. go back under and adjust the link/rod or see if it is hanging up. Did you put the clutch disc in with the long part of the hub towards the pressure plate?

Oct 14, 2009 | 1994 Isuzu Trooper

1 Answer

6.5Lchev diesel to a ford ZF 5 speed gear box


You will need the Chev pressure plate to suit the Chev flywheel and a clutch plate to suit the Ford ZF gearbox. Ford ZF throwout bearing and clutch fork should be fine.

Jul 01, 2009 | 1981 Ford F 100

Not finding what you are looking for?
2000 Ford Focus Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...