At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Preliminary Procedures
Remove the rear seat. Refer to Rear Seat Replacement.
Remove the left quarter lower trim panel. Refer to Quarter Lower Rear Trim Panel Replacement.
Preliminary Procedure
Remove the rear compartment floor stowage compartment tray. Refer to Rear Floor Trim Plate Replacement.
1
Rear Seat Nut (Qty: 6)
Caution: Refer to Fastener Caution in the Preface section.
Tip
Roll the seat forward enough to get access to the nut that attaches the center seat belt assembly to the floor.
Tighten
45 N·m (33 lb ft)
2
Rear Seat Bolt (Qty: 3)
Tip
• Adjust the seat forward or rearward to access the bolts.
• Remove the plastic trim pieces to gain access to the nuts.
Tighten
45 N·m (33 lb ft)
3
Rear Seat Assembly
Preliminary Procedures
Remove the quarter upper trim finish panel. Refer to Quarter Upper Trim Panel Replacement.
Remove the rear compartment trim panel. Refer to Rear Compartment Trim Panel Replacement.
Remove the floor trim plate. Refer to Rear Floor Trim Plate Replacement.
1
Quarter Lower Trim Finish Retainer (Qty: 2)
2
Quarter Lower Trim Finish Panel Assembly
Caution: Refer to Fastener Caution in the Preface section.
Procedure
Remove the cargo tie down loop anchor plates and bolts.
Remove the rear passenger seat belt guide.
Disconnect the rear passenger seat belt so that the trim panel can be removed around the seat belt. Refer to Rear Seat Belt Replacement.
Pull the trim panel toward the inside of the vehicle to disengage the retainers.
Tighten
9 N·m (80 lb in)
3
Quarter Lower Trim Finish Panel Retainer (Qty: 5)
To get at the speaker, you need to remove the rear window shelf trim panel -
Remove rear seat lower by lifting from front;
Remove bolts holding rear seat back and remove seat back; Remove the seat belt retractors;
Remove the push in retainers from the cross car beam;
Lift up on the front of the shelf panel to disengage the hook and loop material; then do the same at the rear of the panel, and pull out the shelf.
The speaker is now accessible for removal.
The rear seat is four (4) pieces.
You will need two tools a 6mm and 8mm wrenches. 1.) Unbuckle the rear seat belts. 2.) Locate the bolt in the center part of the rear seat, between the cushion and the seat-back. Remove the bolt with a 6 mm socket wrench. 3.) Push down firmly on the front edge of the rear seat cushion and pull it toward you to unhook and remove the rear seat cushion. Push the seat belt stalks through the center holes and lift the cushion out of the Accord. 4.) Pull the lever on the side of the rear seat bolster to lower the rear seat-back, which must be in the down position to access its bolts. 5.) Slide the center seat belt toward the passenger side of the vehicle. Move the loop over the edge of the seat-back to prevent it from hindering removal. 6.) Remove the three bolts from the bottom edge of the rear seat-back, using an 8 mm socket wrench. One bolt is in the center; the other two bolts are on either side. 7.) Pull the rear seat-back out of the Accord. The remaining sections of the seat should be the two side bolsters. 8.) Remove the bolts from the bottom of the side bolsters with a 6 mm socket wrench. Push firmly against the first side bolster. Push it upward to slide it out of its mount. Repeat the process on the bolster on the other side to finish removing the Accord's rear seat.
This should take approximately 15-30 minutes depending hoe mechanically inclined a person is.
PUSH IN CENTER FRONT EDGE CUSHION TO DISENGAGE PART OF SEATS WIRE FRAME FROM CLIPS.WITH CLIPS UNHOOKED LIFT UP AND REMOVE SEAT.IF REAR SEAT NOT HELD IN PLACE WITH CLIPS. LIFT UP THE REAR SEAT CUSHION AND PIVOT IT FORWARD. DETACH THE RETAINING BOLTS AT THE LOWER EDGE OF THE SEAT BACK AND IF NECESSARY REMOVE THE SEAT BELT ANCHOR BOLTS.LIFT UP ON SEAT BACK REMOVE IT..
Hi, follow the instruction below...... Rear See Figures 3, 4, 5 and 6
Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips
Remove upper rear seat back-to-chassis bolts.
Fig. 4: Remove the bolts behind the center armrest ...
Fig. 5: ... and the bolts on the lower corners ...
Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat
Remove rear seat back by tilting forward and pulling straight up.
To install:
Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)
Remove the lower seat cushion by pulling straight up on the front
portion and disengaging the clips. Then hinge the seat upward to release
the rear clips.
Fig. 3: Pull up on the front of the lower seat cushion and
disengage the clips
Remove upper rear seat back-to-chassis bolts.
Fig. 4: Remove the bolts behind the center armrest ...
Fig. 5: ... and the bolts on the lower corners ...
Fig. 6: ... Then pull up on the seat to disengage the three
clips on the top of the seat
Remove rear seat back by tilting forward and pulling straight up.
To install:
Install the lower seat cushion and torque the lower rear
seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
Install the upper rear seat back cushion and torque the upper rear
seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)
Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED
Description
Tool Number
Safety Belt Bolt Bit
T77L-2100A NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.
Removal
Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear
Sedan Removal
Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
Remove rear seat cushion from vehicle.
Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear
60/40 Split Bench—Sedan Removal
NOTE: Safety belt bolts do not secure seat back to vehicle.
Remove rear seat cushion as described.
Fold down back seat and remove two bolts in the center of each seat back striker plates.
Remove two bolts from outboard rear seat back frame retaining brackets.
Lift seat back up and pull forward to remove from vehicle.
Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan
Removal
Remove rear seat. Refer to Section 01-10 .
Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
Pull lower quarter trim panel away from body.
Remove safety belt retaining bolt.
Feed safety belt through lower quarter trim panel.
Remove safety belt anchor plate-to-sill bolt from quarter panel.
Remove retractor anchor nut and retractor from rear quarter panel.
Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
Slide anchor plate end of safety belt through the openings in the quarter trim panel.
Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
Item
Part Number
Description
1
386277-S190
Bolt (Part of 611B68)
2
31012
Upper Rear Quarter Trim Panel
3
611B60
Retractor and Tongue
4
N800937-S190
Nut
5
389370-S190
Bolt
6
—
Rear Quarter Panel (Part of Body)
7
52018
Lower Rear Quarter Trim Panel
8
—
Mounting Stud (Part of Body)
Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
Installation
To install, reverse Removal procedure.
Make sure the safety belt webbing is not twisted. If it is, remove the twist.
Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
I think you have to remove headrst bfore folding seat back down. You may have to unbolt seat from floor. 4 bolts.
Rear Seat Backrest —Split Bench
Removal NOTE: The 40% rear seat backrest must be removed before the 60% rear seat backrest. 40% rear seat backrest
Remove the 40% rear seat backrest.
Remove the nuts and bolts.
Remove the backrest.
60% rear seat backrest
Remove the 60% rear seat backrest.
Remove the nut and bolt.
Remove the backrest.
Installation NOTE: The 60% rear seat backrest must be installed before the 40% rear seat backrest. 60% rear seat backrest
NOTE: Do not tighten the nut and bolt at this time. Install the 60% rear seat backrest.
Install the rear seat backrest.
Install the nut and bolt.
40% rear seat backrest
NOTE: Do not tighten the nuts and bolts at this time. Install the 40% rear seat backrest.
Install the rear seat backrest.
Install the nuts and bolts.
60/40% rear seat backrest
Tighten the 60/40% rear seat backrest nuts and bolts in the sequence shown.
40% Rear Seat Backrest
Tighten the 40% rear seat backrest nuts and bolts in the sequence shown.
it is not designed to be removed. It is designed to slide back and forth as needed.
Section 01-10: Seats and Tracks
1998 Villager Workshop Manual
REMOVAL AND INSTALLATION
Seat, Rear
Bench Removal
Remove the center seat(s) if equipped. Refer to the procedure in this section.
Slide the bench seat forward to the center row seating position.
Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.
Remove the two rear seat bolts from the front of the rear seat cushion latch cover.
Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.
Remove the bench seat from the vehicle through the body side door opening.
×