Please I need torque settings for Golf 5 GTI 2.0 for crankshaft main bearings and big ends; mains and cylinder head?

READ
https://eautorepair.net/Marketing/Default.asp

what country, if USA it is all there (lost your service manual)
here is ours.
https://eautorepair.net/Marketing/Default.asp


RTM.

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

This manual has everything but cam torque

http://www.championbrands.com/aera-torquespecs.pdf

Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

https://www.google.com/search?q=Need+a+fuse+diagram+for+2012+Volkswagen+jetta+se+2.5&biw=1362&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwjz0O-MzZrQAhVC6CYKHYj2C54QsAQIIw&dpr=1#tbm=isch&q=How+do+I+torque+main+and+big+end+bearings+on+a+2005+Volkswagen+Golf+GTI

Hope this helps

Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :

• Use new bolts and tighten as follows:
  • 1,4/1,6 = 35 Nm + 30° + 15°
  • 1,8/2,0 = 65 Nm + 30° + 15°
• "Pot"-type flywheel = 65 Nm + 30° + 15°
• Tighten drive plate to 60 Nm.

Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :

• Tighten nut in three stages:
  1. 130 Nm
  2. Slacken off
  3. 20 Nm + 80°-90°.

Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

You will need to carry out these steps for optimal settings
• 1st stage 40nm-wait for five minutes
• 2nd stage 60nm leave 5 mins
• 3rd stage 90 degrees leave 10 mins
• 4th stage 90 degrees

CYLINDER HEAD BOATS TORQUE FIRST PASS 29.5 FT LBS SECOND PASS 44 FT LBS.THEN TIGHTEN ADDITIONAL 90 DEGREES FOR MAIN BEARINGS 15 FT LBS TIGHTEN EACH BOAT ADDITIONAL 70 DEGREES ROD BEARINGS 15 FT LB TIGHTEN ADDITIONAL 70 DEGREES. CRANKSHAFT DAMPER BOLTS 130 FT LBS.

Crankshaft torque settings for 2002 Audi TT 225 BHP:

1. Main bearings: Renew bolts = Yes
2. Main bearings: Stage 1 = 65 Nm
3. Main bearings: Stage 2 = 90 degrees
4. Big end bearings: Renew bolts / nuts = Yes
5. Big end bearings: Stage 1 = 30 Nm
6. Big end bearings: Stage 2 = 90 degrees
7. Flywheel / driveplate = 60 Nm + 90 degrees (use new bolts / nuts)
8. Crankshaft pulley / damper centre bolt = 90 Nm + 90 degrees (use new bolts)