Question about 2004 Nissan Sentra

2 Answers

Head light have low but when using high does not work just on one side drivers side

Need to no where the wiring is for this problem high beam not working on drivers side

Posted by on

  • Jerry Ross
    Jerry Ross Dec 20, 2015

    Sorry I don't have a wiring diagram. But if you google the make and model you might find enough information to help or else if possible trace the wire and see if you can see anything.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 1,061 Answers

Sounds like the high beam is burnt out on the light on the driver side. You may want to change the headlight or put a different power supply to the bulb and that will tell you if the light is burnt out or if it is the wiring. Just run a hot wire from the battery.

Posted on Dec 20, 2015

Testimonial: "No the light is not burnt it is new already change that and tested the power to the build and it's the wires for high beam need to find where these wires go can you help me"

  • Jerry Ross
    Jerry Ross Dec 20, 2015

    Not being a Nissan expert and after second thought you might want to check the dimmer switch and see if one leg of it is burnt out.

×

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 9,098 Answers

HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Posted on Dec 20, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pontiac 2006 g6 headlights are not working proper drivers side only works in high beam and I only get a faint low beam on passenger side


How did jump starting the vehicle burn headlamp wire ? Check the left low beam fuse # 7 10 amp - located in the underhood fuse / relay box. Does the high beam work on the right side ? The light that is dimly lit has a ground issue or not enough voltage ,testing that circuit using voltage drop testing would be the way to find the problem . Do you know what a wiring diagrams is ? an how to read one ? How to use a DVOM - digital volt ohm meter to test electrical circuit's ? Watch these two guy's video on voltage drop testing.

Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year ,make , model an engine . Under system click on lighting , then under subsystem click on headlamps . Click the search button then the blue link . Learning how is the first step in automotive electrical diagnostic's .

Electric Testing Techniques You Need to Know

May 31, 2018 | Pontiac Cars & Trucks

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

1 Answer

1998 Saturn Sc2 coupe Only drivers side low beam comes on passenger side off it has no power High beams work How can I fix this?


Find the break in the power wire for the low side. High beam works, ground is good. Low beam works on the other side, so you have power threw the switch and turn signal. Wires usually break close to the plug. Also check the plug for corrosion. White to a greenish color.

Oct 23, 2015 | Saturn Cars & Trucks

2 Answers

Low beam headlight drivers side don`t work. high beam it works.


Check tour bulbs first and replace if blown. If OK then check wiring backwards from light to dip switch.

Oct 05, 2012 | 1996 Ford Explorer

1 Answer

Low Beam Drivers Side doesn't work ... low voltage,


Power for the headlights on the Left side (High and low beam.) comes from the same fuse... The ORANGE wire and the ORANGE/BLACK are the same, they connect in the harness. If you only lack the 12v to make the light work connect them at the headlight assembly.

If your low beam also lacks ground the Left low beam ground is shared with the right low beam ground... Run a wire from left low beam DARK BLUE to right low beam DARK BLUE/WHITE.

If its not working now then your cursed, seek a witch doctor.

May 23, 2010 | 2004 Buick Regal

1 Answer

F 150 Head light issue


You know the fuse for the high beams is good ( Cab fuse panel fuse # 16 ) and the pass low beam fuse ( cab fuse panel # 26 ).
Might want to check cab fuse panel fuse #28 ( this is the driver's side low beam ).

If this fuse has power on both sides ( with the low beams on ) next you can pull the headlamps, and check for power at the connectors, but depending when the last bulb change took place, I would say you need need bulbs. ( need at least 1 for the high beam out )
Confirming with a meter at the headlamp would be a good idea, before spending the money.

The bulb connector has 3 pins.
Black wire is ground on both sides
Light Green w/ Black stripe wire is high beams on both sides
Driver Lo = Dark Blue w/ white stripe
Pass Lo = Dark Green w/ Orange stripe.


Nov 16, 2009 | 2002 Ford F150 Regular Cab

2 Answers

One high beam works one doesn't, gauge cluster does not light up


you say you replaced both bulbs, you mean right and left or both the high beam and the low beam on left side?could be a bad ground for the left headlight. there should be some ground wires there near the headlight, LF corner under hood. without a wiring diagram here at home,I am not much help.

Sep 26, 2009 | 2000 Honda Accord

1 Answer

How can i disconnect the high beams because when i turn my normal lights on the high beams come on. I need to know how I can disconnect them.


there are 3 wires going to each headlamp,a ground,a low beam,and a high beam.. cut the high beam wire, and do both sides .and if you want high beams to work,wire both sides to a single throw double pole switch for the high beams to turn on and off.

Jul 22, 2009 | 1991 Toyota Tercel

Not finding what you are looking for?
2004 Nissan Sentra Logo

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...