How can I remove the glove box? - 1999 Lincoln Town Car

if you feel under the glove box toward the back you will feel some bolts remove these and the glove box will come out

Instructions

1. • 1

     Remove the battery cover to access the battery terminals. Disconnect the negative (-) battery cable with the pliers.
     

   • 2

     Open the glove box door and squeeze the outer part to remove the door. Locate the two screws behind the door to remove the glove box.
     

   • Sponsored Links
     

     • ECM's - $190

       Lifetime Warranty Engines & Trans. Same-day turn around.
       www.avproecm.com

   • 3

     Access the ECU behind the glove box. Remove the electrical connectors by hand; remove the bolts mounting the ECU to the inner dash.
     

   • 4

     Install the new ECU in the same position. Replace the bolts and reconnect the electrical connectors.
     

   • 5

     Replace the glove box and the glove box door. Reconnect your battery.
     

Sponsored Links

Read more: How to Replace a Toyota Avalon ECU ' eHow.com http://www.ehow.com/how_6170111_replace-toyota-avalon-ecu.html#ixzz289jiGlka

Remove the glove box door. The PCM in a Grand Am is located behind the glove box. You do not need to remove the entire glove box, just the door. Remove the glove box by opening the door any emptying its contents. Squeeze together the outside part of the glove box that becomes visible while open. Squeezing it will release the clip from its fastener, and the glove box will slip right off.


Thanks
Tom Miller

This something I copied from an eBay listing, so I haven't done it yet.

Uplander Glove Box Hinge

Used in good condition.

Has minor cosmetic flaws like scratches, scrapes or scuffs you would normally expect to find on a used item.

Includes 5 screws and nuts to replace the rivets.

A web search may yield a video for you to watch.

Required Tools:

Flat screwdriver

Phillips screwdriver or else a 7mm socket and rachet

Electric drill with a 3/16" inch bit

Needle nose pliers or vise grips.

3/8" inch wrench.

Removal Instructions:

Remove the panel underneath the glove box.

3 Black 3/4" inch pan head bolts hold it in place.

Use a flat screwdriver to pry a little and slip the prongs of a pair needle nose pliers on either side of a bolt.

Push down on the handle of the needle nose pliers to remove each bolt.

Remove 2 phillips screws along the bottom of the glove box hinge.

Remove 2 phillips screws inside the glove box.

Remove the small black cabin air filter access door inside the glove box.

Put your fingers inside the left side of the access door opening.

Yank backward to loosen the 1 retainer clip on the left side of the glove box assembly.

Often times the 2 retainer clips on the right are also loosened.

Skip steps 1 to 5 if you can remove the entire glove box assembly at this point.

1) Open the front passenger door.

2) Use the flat screwdriver to remove the fuse access panel.

3) 3 Retainer clips hold it in place.

4) Use both hands to grab the glove box assembly on the far right.

5) Yank backward to loosen the 2 retainer clips on the right side of the glove box assembly.

Pull the entire glove box assembly out of the dashboard.

Some models have a strip of masking tape behind the glove box to hold it in place.

Some models have a lamp inside the glove box. Leave it in place or else pry a black tab to disconnect the wiring harness.

Hold the 'ears' of a rivet with the vise grips or needle nose pliers.

Drill through the 5 rivets with your electric drill and 3/16" inch bit.

The rivets may fall apart. Otherwise, twist the vise grips or pliers for removal.

Remove 4+2=6 phillips screws on the glove box door.

Use a flat screwdriver to pry 2 tabs on the glove box door to remove the rectangular portion.

Installation Instructions:

Install the 4+2=6 phillips screws on the glove box door.

Install the 5 replacement phillips screws and nuts where the rivets were.

For some models reconnect the glove box lamp wiring harness.

Align the 3 retainer clips and push the fuse access panel into place.

Align the 3 retainer clips and push the glove box assembly firmly into place.

Install the small black cabin air filter access door inside the glove box.

Install 2 phillips screws inside the glove box.

Install 2 phillips screws along the bottom of the glove box hinge.

Install 3 black 3/4" inch pan head bolts under the glove box assembly to hold the panel in place.

- Done -

Hello, I'm sending you exploded view of the glove box and the in cabin micro filter cover illustration. Remove the two upper screws on the glove box and carefully pry metal clips loose.
Disconnect glove box lamp electrical connector. Do not let glove box assembly hang from glove box lamp harness.
Remove three lower screws and remove damper clip from glove box door. Separate glove box housing and passenger instrument lower panel.
Remove three screws and remove in cabin micro filter cover.
Remove in cabin micro filters from front heater and cooling unit assembly.
Note When installing two new in cabin micro filters ensure that the filters are facing in the direction indicated by the direction arrow for the airflow. Direction arrow is printed on side of in cabin micro filters.
Install in cabin micro filter cover. Reinstall glove box.
Thanks

open the glove box door, remove everything from inside the glove box. remove the clip retaining the door-stop strap. pivot the glove box downward,unsnap the hinges from the instrument panel and remove the glove box. install in the reverse manner.

First, take a good look at what you’re doing.
Look on the right side of open glove box and locate a plastic lever. You will see grooves on the end connected to the glove box. The grooved area is the spot to place the thumb in order to press this lever off the glove box when it comes time to do that.
Look up under the glove box. You will see two brass colored screws one on each side of the bottom of the glove box. These screws go up through two square plastic hinges that are attached to the glove box and into the the dash frame.
Okay, with the glove box closed remove the two brass colored screws, and put them aside so you won’t lose them..
Open the glove box and hold the glove box with your left hand and press on the plastic lever (grooved area) located on the right side of the glove box. This lever (the lever already mentioned above) is slotted and will pop off the glove box.
Put the glove box carefully aside.
Look straight in behind the glove box. You will see a rectangular black plastic cover approximately 1.5 inches wide by 8 inches long. On the right and left side are arrows pointing in. Press the arrows and pull out on the cover. This will slide out the tray that holds the filter. Remove old filter and insert the new one, flow arrows pointing down.
Retrieve glove box, hold in place, and attach plastic plastic lever to the right side of the glove box. The reverse of removal.
Next, the two plastic hinges located on the bottom of the glove box fit underneath the dash frame.
While holding the glove box in place (the glove box latch may hold glove box in place while installing screws) re-install the two screws through the plastic hinges into the frame and tighten.
Hope this helps you.

I'm going to send you exploded view of the glove box and the in cabin micro filter cover illustration. Remove the two upper screws on the glove box and carefully pry metal clips loose.
Disconnect glove box lamp electrical connector. Do not let glove box assembly hang from glove box lamp harness.
Remove three lower screws and remove damper clip from glove box door. Separate glove box housing and passenger instrument lower panel.
Remove three screws and remove in cabin micro filter cover.
Remove in cabin micro filters from front heater and cooling unit assembly.
Note When installing two new in cabin micro filters ensure that the filters are facing in the direction indicated by the direction arrow for the airflow. Direction arrow is printed on side of in cabin micro filters.
Install in cabin micro filter cover. Reinstall glove box.

While holding the lower glove box, release the damper and remove the glove box stop on each side.
Remove the bolts, then remove teh lower glove box. Install the lower glove box in the reverse order of removal.

It should be the same general procedure as the 02. Open Glove box and remove contents. Remove glove box stops and or glove box shock on side. With the glove box swung out of the way remove the panel that covers the air filter. Remove and replace filter. Reinstall cover, and glove box stops.