The radio stopped and a sigh reads cd6 track 1. I cannot change the source.

Yes there is. Even the cheap radios have a fuse on the back side of the radio unit.

Stop by any good parts store (Autozone, Advance, etc..) and have them test your charging system and load test your battery. I think you'll find your answer between those two tests.

Hi and welcome to FixYa!

Pretty much a worn out clutch lining. If the clutch lining is worn out, it tends not to stop the flywheel and will surely cause a grinding sound.

I strongly suggest that you replace the clutch lining, pressure plate and release bearing to resolve the problem.

Hope this helps and thank you for using FixYa! Have a good one!

Which three fuse's did you replace ? You should check for B+ voltage on both side's of the fuse . Two little metal tabs on top of the fuse. Voltage on both , fuse is good .
Try radio self-diagnostic mode .
A fluctuating AC voltage audio signal is sent to the speakers directly from the audio unit to reproduce sound. The audio unit has a self-diagnostic mode that can be entered by pressing preset buttons 3 and 6 simultaneously.
Visual Inspection Chart Mechanical Electrical

• Audio unit
• Antenna or antenna cable
• Speaker mounting/speaker cones
• Radio ignition interference capacitor, radio frequency interference suppression bond, or radio receiver hood bonding strap

• Smart junction box (SJB) fuse(s):
  • 7 (10A)
  • 12 (5A)
  • 16 (15A)
• Battery junction box (BJB) fuse(s):
  • 7 (40A)
  • 15 (20A) (Hybrid)
  • 16 (25A)
  • 21 (40A)
  • 22 (40A) (Hybrid)
  • 23 (40A) (Hybrid)
• Subwoofer amplifier
• Circuitry
• Audio unit

1. If the concern is visually evident, GO to Symptom Chart .

1. If the concern is not visually evident, proceed to the Speaker Walk-Around Test and the Audio Unit Self-Diagnostic Mode.

Speaker Walk-Around Test (Except Premium CD6)
NOTE: To enter the speaker walk-around test or audio unit self-diagnostic mode, the audio unit must be turned on and in the radio tuner mode (AM/FM).

1. To enter the speaker walk-around test, simultaneously press the audio unit preset buttons 3 and 6.

1. The speaker walk-around test stops at each speaker and applies sound to each speaker for about 1-2 seconds. Each speaker is tested and displayed on the audio unit in the following sequence: RF, LF, LR, RR and SUBWOOFER.

1. To exit the speaker walk-around test, turn the ignition switch off, turn the audio unit off, or press preset button 1 for diagnostics (DIA).

Audio Unit Self-Diagnostic Mode (Except Premium CD6)
NOTE: To enter the speaker walk-around test or audio unit self-diagnostic mode, the audio unit must be turned on and in radio tuner mode (AM/FM).

1. To enter the following tests, press the desired preset button while in the speaker walk-around test or while in the audio unit self-diagnostic mode.

1. To exit the audio unit self-diagnostic mode, turn the ignition switch or the audio unit off.

1. If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.

1. The self-diagnostic mode has 6 manual tests available:
   • Preset button 1 = ENTER DIAGNOSTICS. This test enters diagnostics from the speaker walk-around test. Metrics are available with SEL and ON buttons indicating time played in AM/FM, media, number of buttons pressed, etc.
   • Preset button 2 = EEPROM BLOCK STATUS. This test shows the validity of memory to calibrate the clock, and seek sensitivity.
   • Preset button 3 = EXIT DIAGNOSTICS.
   • Preset button 4 = Software configuration level. This test queries each radio system controller for its software configuration level.
   • Preset button 5 = DISPLAY TEST. This test lights all the display segments for five seconds and then turns all segments off.
   • Preset button 6 = RAM CONTENTS READOUT. To enter these tests, press preset button 1 while in the speaker walk-around test, then the desired preset button.

1. To exit the self-diagnostic mode, turn the audio unit or the ignition switch off.

1. If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.

The following is the owner's manual for your 2004 Dodge Neon:

http://www.dodge.com/en/owners/manuals/index.html?year=2004&nameplate=Neon

P.99 describes how to load discs:

1. Select and press any numbered button without an illuminated light above it.
2. Insert the CD while the light above the chosen button is flashing and the two lights on either side of the slot are illuminated.
3. Upon insertion, the CD will begin to play, and both the button light and the lights in the corner of the loading slot will illuminate.
4. Repeat the process for loading any additional CDs. The CD playe rwill stop while additional CDs are loaded.

Playing Discs
The radio will show the CD number, the CD track number, and the Track Time Elapsed while the radio is in the CD mode. IF more than one CD is loaded in the changer, the changer will automatically play the next disc after playing the last track of the current disc.

Wow, that's a lot of typing.
I didn't know the 2004 Dodge Neon had such a nice changer.
Good luck.

OEM cd players are set up to keep burned cds from playing well or at all. Some will work better if you use a better cd brand or quality cd.

you dont,it has no connection BUT you can get a fm transmitter the fits the ipod and you just tune your radio into it......so can the guy behind......and the one in front...

the central processor chip in the radio has gone out you should just replace the radio

Heres an easy fix for it, and can improve your sound quality, Change the radio head unit entirely. OEM (factory) head units are ****, and you can get aftermarket that accept OEM cd-changers.

Try this if it works to your unit;

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

hope this may help;

Regards,
VOTIT

DON'T FORGET TO RATE;