Key wont turn pass acc it locks how can i fix

hi jerome
I have the procedure for Toyota auto lock, is worth to try it
AUTOMATIC LOCK SETTING
1) Step in the vehicle and make sure that all doors are closed completely
2) Insert the key into the ignition key cylinder.
3) Wait for more than 5 seconds.
4) After turning the key to the ACC position, turn the key from the ACC to the
ON position 5 times within 10 seconds (Last position : ON).
? Status Monitor LED will illuminate for 30 seconds.
Note : In case you implement 6 times or more by mistake,
action steps 6)-8) you made will be canceled.
Please retry from step 2).
5) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key to the ACC position.
? LED will continue illuminating.
? Indicator lights will flash 2 times.
Ignition controlled door lock ON :
6) While the LED is illuminated:
• Open and close the driver's door 1 time.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 1 time.
? LED will extinguish.
Ignition controlled door lock OFF :
6) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 2 times.
? LED will extinguish.

1997 Toyota Camry Key Wont turn, Ignition Lock problem -1997 toyota camry FIXED!!! I see a lot of Douches with a capital D trying to charge people to fix this extremely common issue with this Camry ignition cylinder. OK pull the plastic guard off encasing the steering column. Get a phillips head screwdriver and remove the 2 screws holding the little off-white connector at the rear of the module(it has the wires to the ignition running to it). Get a pair of pliers or a small crescent wrench and while trying to turn the key use the wrench to turn the little rod sticking out of the back of the module. Make sure your turning it WITH the direction the key is trying to turn it. It should immediate be freed. Voila IT WORKS! AND THATS WHY PEOPLE DONT TRUST MECHANICS! HOW CAN YOU CHARGE SOMEONE FOR THAT INFO?

There is an internal failure in the ignition switch. Replace the switch. You can get them at any auto parts store, it includes the switch and 2 new keys. Please rate solution if this helps. Have a great day!

dependind on make of car,u can remove the steering wheel and push the lock button in

GRAND PRIX KEY FOB PROGRAMMING INSTRUCTIONS 
Important 
Once the Keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver. 

Perform the following steps:
Sit in the vehicle driver's seat. (actually it’s much eazy er from the front pass seat) 
Remove the ignition key from the ignition lock cylinder. 
Close all of the vehicle's doors. 
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis. 
Turn the ignition lock cylinder to the ACC position. 
Turn the ignition lock cylinder OFF, then back to ACC within 1 second. 
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important 
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.

Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. 
Repeat step 8 in order to program each additional transmitter. 
Remove the ignition key from the ignition lock cylinder. 
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis. 
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation.

Good luck and hope this helps. 

try to remove the fuse , usually the light is on when the key is in ACC. double check the key position . turn it to lock position. Or the ACC wiring is still positive even though the key in lock. In this case shorted wire is occur.

make sure you are pushing in on the key while turning it to the off position

cars have a lock position to protect the car from being stolen by theives. When we park the car with the wheels turned to the sides it gets locked in that position and the key can sometimes nbe hard to take out. Try moving the steering wheel in both directions as much as possible while pushing in the key and trying to jiggle it to turn. If you can get it out, the next time , park your car with the wheels facing forward. I hope this works.

can you use the key its self on the rear door. what i mean is not using the remote but actually using the key?

something is wrong with the shifter going into park or the actual ign. lock assy is faulty