Why doesn't selection indicator show the square box around the park position?

What is it chiming ? Chimes for different reasons , headlamps on , seat belt not buckled , etc.... What warning light is lit on the instrument cluster ? if any . seat belt , air bag's etc...

Audible Warnings Description and Operation
The audible warnings alert the driver of a system concern or a critical vehicle condition. The following lists the audible warning priority and the pulse rate:
Fast rate chime (200 pulses per minute)
Medium rate chime (150 pulses per minute)
Slow rate chime (50 pulses per minute)
Single chime
Fasten Safety Belt Warning
The inflatable restraint sensing and diagnostic module (SDM) activates the fasten safety belt audible warning for 5-8 seconds. The fasten safety belt warning sounds and the fasten seat belt indicator illuminates when the following occurs:
• The ignition switch is in RUN, BULB TEST, or START position.
• The SDM detects that the driver's seat belt is not buckled (signal is low).
If the seat belt is buckled before the ignition is in RUN, BULB TEST, or START position, the chime does not sound. If the seat belt is buckled while the chime is sounding, the chime stops.
Key-In-Ignition Warning
The instrument panel cluster (IPC) activates the key-in-ignition audible warning. The key-in-ignition warning sounds when the following occurs:
• The ignition switch is in OFF, LOCK, or ACCY position.
• The body control module (BCM) determines that the driver's door is open (signal is low).
• The BCM determines that the key-in-ignition switch is closed (signal is low).
Lights On Warning
The instrument panel cluster (IPC) activates the lights on audible warning. The lights on warning sounds when the following occurs:
• The key is not in the ignition.
• The body control module (BCM) determines that the drivers door is open (signal is low).
• The BCM determines that the headlamp switch is in the park or head position.
Rear Parking Assist
The rear object sensor control module activates the audible warning. The audible warning sounds whenever any of the indicators are illuminated on the rear parking assist display. For a description of the rear parking assist system refer to Object Detection Description and Operation.
Turn Signal Reminder
The instrument panel cluster (IPC) sounds the turn signal reminder once per each flash of the turn signal lamps when:
• The ignition switch is in the RUN position.
• The turn signal switch is in either turn position, sensing, within 1 second, an open to B+ transition in the turn signal control circuit (left or right turn).
• The vehicle has traveled a distance of 1.2 km (0.75 mi) by counting pulses on the vehicle speed input circuit.
The IPC turns off the turn signal reminder when either the ignition switch is turned to the LOCK position or to the OFF position, or the turn signal switch returns to the OFF position, sensing, within 1 second, no transitions from open to B+ in either of the turn signal control circuits (left turn or right turn).
Additional Chimes
The following chimes will turn on when an associated indicator turns on in the instrument panel cluster (IPC):
• Low Fuel Indicator
• Low Oil Pressure Indicator
• OVER SPEED indicator
For a description of an indicator refer to Indicator/Warning Message Description and Operation.
For diagnosis of an indicator refer to Symptoms - Instrument Panel, Gages and Console.

Your have a problem with one of these systems , your best bet , take it to a qualified repair shop. They would do diagnostic's to find the problem .

Do any indicators illuminate when the chime sounds?
Go to Symptoms - Instrument Panel, Gages and Console
Go to Step 3
3
Turn the ignition OFF.
Remove the key from the ignition.
Turn the headlamp switch to OFF.
Close all of the vehicle doors.
Open one or more of the vehicle doors
Does the chime sound at all times regardless if the doors are open or closed?
Go to Step 15
Go to Step 4
4
Close all of the vehicle doors.
With a scan tool, observe the LF Door Ajar Switch parameter and the RF Door Ajar Switch parameter in the instrument panel cluster BCM/Inputs data list.
Do all of the Door Ajar Switch parameters display Door Closed?

With a scan tool, observe the Left Rear Door Ajar Sw. parameter and the Right Rear Door Sw. parameter in the instrument panel cluster BCM/Inputs data list.
Do all of the Rear Door Switch parameters display Closed?

This is a 21 step diagnostic trouble shooting flow chart .

Who replaced the headlamp bulb ? Take it back . Everything your having problems with are all controlled by the BCM - body control module . May have crossed wire's ,shorted etc....
This vehicles BCM functions as the Power Mode Master (PMM). Refer to Power Mode Description and Operation for a complete description of the power mode functions.
Body Control Module
The various body control module (BCM) input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The BCM functions include the following:
• Battery rundown protection--Inadvertent power--Refer to Interior Lighting Systems Description and Operation .
• BTSI/automatic transmission shift lock control--Refer to Automatic Transmission Shift Lock Control Description and Operation .
• Bulb check--Refer to Instrument Cluster Description and Operation .
• Chimes--Refer to Audible Warnings Description and Operation .
- Check gages
- Content theft deterrent
- Door ajar warning
- Headlamps ON
- Key-in-ignition
- Oil reset
- Park brake warning
- Seat belt not fastened
- Turn signal ON
- Vehicle theft deterrent
• Door lock interface--Refer to Power Door Locks Description and Operation .
• Exterior and interior lighting control--Refer to Exterior Lighting Systems Description and Operation .
- Automatic lighting control
- Backup lamps
- Daytime running lights (DRL)
- Fog lamps
- High/low beam head lamps
- Park brake lights
- Turn hazard lamps
• Gage control--Refer to Instrument Cluster Description and Operation .
• Heated seats--Refer to Heated Seats Description and Operation .
• Horn interface--Refer to Horns System Description and Operation .
• Instrument cluster indicator control--Refer to Instrument Cluster Description and Operation .
• Interior lighting--Refer to Interior Lighting Systems Description and Operation .
• Key-in-ignition sensing--Refer to Audible Warnings Description and Operation .
• Parking brake state sensing--Refer to Brake Warning System Description and Operation .
• Retained accessory power (RAP)--Refer to Retained Accessory Power (RAP) Description and Operation .
• Rear compartment interface--Refer to Power Door Locks Description and Operation .
• Rear defogger--Refer to Rear Window Defogger Description and Operation .
• Remote function control--Refer to Keyless Entry System Description and Operation .
• RFA communication link--Refer to Keyless Entry System Description and Operation .
• Seat belt use sensing--Refer to Seat Belt System Description and Operation .
• Theft deterrent vehicle/content--Refer to Content Theft Deterrent (CTD) Description and Operation or Immobilizer Description and Operation .
• Washer solvent level sensing--Refer to Wiper/Washer System Description and Operation .
• Wiper/washer--Refer to Wiper/Washer System Description and Operation .

This warning indicator is controlled by the BCM - body control module . You cant turn it off , you need to fix the faulty input switch that signals the BCM that the door is open .
Body Control Module
The various body control module (BCM) input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The BCM functions include the following:
• Battery rundown protection--Inadvertent power--Refer to Interior Lighting Systems Description and Operation in Lighting Systems.
• BTSI/automatic transmission shift lock control--Refer to Automatic Transmission Shift Lock Control Description and Operation in Automatic Transaxle - 4T65-E.
• Bulb check--Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.
• Chimes--Refer to Audible Warnings Description and Operation in Instrument Panel, Gages, and Console.
- Check gages
- Content theft deterrent
- Door ajar warning
- Headlamps ON
- Key-in-ignition
- Oil reset
- Park brake warning
- Seat belt not fastened
- Turn signal ON
- Vehicle theft deterrent
• Door lock interface--Refer to Power Door Locks Description and Operation in Doors.
• Exterior and interior lighting control--Refer to Exterior Lighting Systems Description and Operation in Lighting Systems.
- Automatic lighting control
- Backup lamps
- Daytime running lights (DRL)
- Fog lamps
- High/low beam head lamps
- Park brake lights
- Turn hazard lamps
• Gage control--Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.
• Heated seats--Refer to Heated Seats Description and Operation in Seats.
• Horn interface--Refer to Horns System Description and Operation in Horns.
• Instrument cluster indicator control--Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.
• Interior lighting--Refer to Interior Lighting Systems Description and Operation in Lighting Systems.
• Key-in-ignition sensing--Refer to Audible Warnings Description and Operation in Instrument Panel, Gages, and Console.
• Parking brake state sensing--Refer to Brake Warning System Description and Operation in Hydraulic Brakes.
• Retained accessory power (RAP)--Refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power.
• Rear compartment interface--Refer to Power Door Locks Description and Operation in Doors.
• Rear defogger--Refer to Rear Window Defogger Description and Operation in Stationary Windows.
• Remote function control--Refer to Keyless Entry System Description and Operation in Keyless Entry.
• RFA communication link--Refer to Keyless Entry System Description and Operation in Keyless Entry.
• Seat belt use sensing--Refer to Seat Belt System Description and Operation in Seat Belts.
• Theft deterrent vehicle/content--Refer to Theft Systems Description and Operation in Theft Deterrent.
• Washer solvent level sensing--Refer to Wiper/Washer System Description and Operation in Wipers/Washer Systems.
• Wiper/washer--Refer to Wiper/Washer System Description and Operation in Wipers/Washer Systems.

As far as the sliding doors , pull the fuse's

Year make and model would help. Sounds like a A wiring harness is rub threw. Check the black conduit from the switch back to the main harness.

Which insturment cluster does your's have ? electronic instrument cluster or standard instrument cluster !

Standard insturment cluster - speedo / odometer
Speedometer/Odometer
The speedometer and odometer provides speed information based on a speed/distance pulse signal from the vehicle speed sensor (VSS). The VSS is mounted on the speedometer driven gear in the transmission.
Could be the VSS is bad .
Horn The horn system includes the following:

• horn relay
• horn
• clock spring
• steering wheel control switch harness
• steering wheel pad horn switch, which is part of the driver side air bag module. For additional information, refer to Section 501-20B .

The horn is located behind the front bumper mounted to the radiator support.

Is the air bag light lit on the insturment cluster ? If it is the clock spring could be the problem . If not lit check the circuits from the horn relay .

VEHICLE RELAYS Operation Diagnosis .

Which headlamps don't work ? Low beams , high beams , both ?

• The high beams are inoperative

• Bulbs.
• Circuitry.
• Multifunction switch.

• GO to Pinpoint Test C .

• The low beams are inoperative

• Bulbs.
• Circuitry.
• Headlamp switch.
• Multifunction switch.
• LCM.

• GO to Pinpoint Test D .

Principles of Operation
NOTE: Due to varying wattage ratings and resulting current draw, certain aftermarket headlamp bulbs may cause the lighting control module (LCM) to shut down the short circuit protection, resulting in the low beams becoming inoperative. Verify that the headlamp bulbs meet Ford specifications.
Headlamp System The headlamp system consists of:

• two aerodynamic halogen headlamp bulbs and retainers
• headlamp switch
• multifunction switch
• lighting control module (LCM)
• circuit wiring and circuit protection

In normal operation:

• With the multifunction switch in the low beam position, power is supplied by the LCM to the low beam elements through the multifunction switch.
• With the multifunction switch in the high beam position (forward detent), power is supplied to the high beam elements and to the high beam indicator in the instrument cluster.
• When the multifunction switch is pulled toward the steering wheel, the flash-to-pass switch (part of the multifunction switch) is closed and power is supplied to the high beam elements. When the switch is released, they return to low beam operation.
• The battery saver feature of the LCM will automatically turn off the courtesy lamps, demand lamps, headlamps, or parking lamps under the following conditions:
  • The ignition switch is in the OFF position.
  • The headlamp switch is in parking lamps ON or headlamps ON positions.
  • After 10 minutes.

Headlamp Switch The headlamp switch is a multi-position switch.

• The positions include OFF, PARK, and HEAD.
• With the headlamp switch in the PARK position (first detent), a signal is supplied to the LCM which powers the front parking lamps, the tail lamps, the side marker lamps, and the license lamp.
• With the headlamp switch in the HEAD position, power is supplied to the headlamps through the LCM and the multifunction switch.
• The panel dim switch (part of the headlamp switch) is located above the headlamp switch. The panel dim switch operates only with the parking lamps or headlamps on.
• When the panel dim switch is held in the up position, the instrument panel lighting will progressively brighten.
• When the panel dim switch is held in the down position, the instrument panel lighting will progressively dim.

For additional information, refer to Section 413-00 .
Headlamps On Warning Chime If the headlamp switch is left in either the PARK or HEAD position and the driver door is opened, the LCM will sound a headlamps on reminder chime when the following conditions occur:

• The ignition switch is OFF with the ignition key out.
• The driver door is ajar.

For additional information, refer to Section 413-09 .

Inspection and Verification

1. Verify the customer concern by operating the system.

1. Visually inspect for obvious signs of mechanical and electrical damage.

Visual Inspection Chart Mechanical Electrical

• Headlamp switch

• Central junction box (CJB) fuse(s):
  • 6 (15A)
  • 15 (15A)
  • 21 (15A)
  • 23 (15A)
  • 27 (20A)
• Battery junction box (BJB) HI-BEAM HEADLIGHTS (20A) fuse
• Circuitry
• Headlamp bulb
• Lighting control module (LCM)
• Loose or corroded connections

The fuse panel is located underneath the dash, to the left of the steering column, next to the emergency brake pedal. You need to remove the under-dash insulation to access some parts of the fuse panel.


If it doesn't have a diagram inside the box, here's one I found online: http://www.coolcats.net/tech/reference/images/fusepanel.jpg


1 15A Lt. Blue Stop Lamps, Hazard Warning Lamps, Speed Control, Cornering Lamp Relays 2 6A - CB - Windshield Wiper/Washer Pump 3

Spare - Not Used 4 15A Lt. Blue Taillamps, Parking Lamps, Side Marker Lamps, Instrument Cluster Illumination, License Lamps, A/C and Heater Illumination, Radio Illumination, Digital Clock Illumination, Autolamp Relay 5 15A Lt. Blue Turn Signal Lamps, Electronic Day/Night Mirror, Lighted Vanity Mirrors *, Backup Lamps, Illuminated Entry, Keyless Entry, Cornering Lamps 6 20A Yellow Rear Defrost Timer, Chime, Back-Up Lamps, Cornering Lamps, Rear Reading Lamps, Trunklid Release, Digital Clock Display, Illuminated Entry, Anti-Theft Module, Turbo Buzzer 7 15A Lt. Blue Fog Lamps (Turbo Only) 8 15A Lt. Blue Courtesy Lamps, Key Warning Buzzer, Illuminated Entry Module, Glove Box Lamp, Door Lock Relays, Radio Memory, Cluster Memory, Outside Mirrors, Tripminder Module, Analog Clock, Anti-Theft Relay 9 30A Lt. Green A/C Heater Blower Motor 10 20A - CB - Horn, Cigar Lighter, Fuel Filler Door, Flash-to-Pass, Speed Control 11 20A Yellow Radio, Tape Player, Premium Sound Amp, Power Antenna, Graphic Equalizer 12 20A - CB - Power Seats, Power Locks, Keyless Entry 13 5A Tan Instrument Cluster Illumination, Radio, Climate Control 14 20A - CB - Power Windows, Power Moonroof 15 10A Red Taillamps, Rear Side Markers, License Lamps, Electoluminescent Coach Lamps 16 4A Yellow Electronic ATC 17 15A Lt. Blue Electronic Cluster, Tripminder Display, Fuel Gauge (non-electronic cluster), A/C Clutch, Speed Control Module, Graphic Warning Display Module, Electronic Blower Speed Controller 18 10A Red Warning Indicator Lamps, Autolamp System, Throttle Position Sensor, Low Fuel Module, Dual Timer Chime, Tachometer, Washer Fluid Level Indicator

Trunk Lock After Closing
--------------------------
Desc.: What happens to the trunk lock when closing it.

Settings:
Yes: Automatically lock Boot on closing
No: Boot can be reopened using micro switch button located on the trunk/boot

* Trunk Lock After Drive Off
----------------------------
Desc.: Should the trunk be locked at drive off or after 30 sec.?

Settings:
Yes: Trunk/Boot will automatically lock when vehicle increases speed
No: Trunk/Boot will remain closed, however will be in the unlocked
condition if No was selected in the previous option.

* Door & Trunk Unlock at Key Out
--------------------------------
Desc.: When the is removed from the center console should door/trunk
be unlocked?

Settings:
Yes: All Doors & Trunk/Boot will Unlock when the Key is removed from
the Ignition Switch If Driver frequently locked all Doors when
driving
this feature would be beneficial.
No: Doors and Boot will remain in the same condition as they were
prior
to Key removal

* TSL Locking Logic (Theft Security Locking/Deadlock)
-------------------
Settings:
TSL at first Press: Default Setting. All Doors will lock in Deadlock
Mode
TSL at Second Press: All Doors will lock in Deadlock mode at the second
press of the Remote.

* Lock /Unlock Acknowledge
--------------------------
Settings:
None : No acknowledge will be visible
Indicators: Indicators will blink as acknowledge

* Follow Me Home Function
-------------------------
Settings:
Tail Light: When selected Tail Lights will be illuminated
Back Up Light: When Selected Reverse Light will be activated


Tech 2 Body Exterior Lighting & Horn
====================================

* High Beam Follow me home Active Time
--------------------------------------
Desc.: Follow Me Home Active Time can be adjusted between 0- 10 minutes

Settings:
This Feature can be turned on or Off .Yes / No can be selected.
Low Beam Automatic / Low Beam also in Position 0 (light switch)
Yes / No
Follow Me Home Active Time
- Daytime Driving Lights can be activated

* Parking Lights
----------------

Settings:
Act as Lead Me To the Car Light.

* Park Light On Reminder
------------------------
Settings:
On / Off
If Ignition is turned Off and the parking lights are active, Driver will
be warned if set to on.

* Show Trailer Light Outage
Desc.: REC will detect blown trailer light and display on SID

Settings:
Yes or No

* Trailer Light / Fog Light off
-------------------------------

Settings:
Yes: Fog Light Rear will be disabled When Trailer is connected Yes
No

* Horn Lock Unlock Acknowledge
------------------------------
Settings:
On: Horn will honk when car is locked
Off: Horn will not honk if car is locked


Tech 2 Body Locking
===================

* Panic Alarm Activation (Vehicles fitted with /Alarm only)
-----------------------------------------------------------
- Panic Button / Locking Switch
Central Locking Switch Driver /Passenger

Settings:
- Panic Button on Remote and locking switch inside vehicle will
activate alarm
- Panic Button will activate Alarm only
- Locking Switch inside vehicle (driver /passenger will activate
alarm only
- No Panic Alarm function required.

* Unlock Logic
--------------
Settings:
All at first press : All Doors will open & Fuel Lid will unlock if the
Driver or Passenger Door Switch is activated
Driver Door & Fuel Lid at first press : Only the drivers Door will unlock
& Fuel Lid will unlock when door
switch is activated

* Remote unlocking One Press
----------------------------
Settings:
All at first press: All Doors will open & Fuel Lid will unlock if the
Remote is pressed
Driver door & Fuel Lid at first press: Only the drivers Door will unlock &
Fuel Lid will unlock when the Remote
is pressed

The TPMS light (Tire Pressure Monitoring System) for that vehicle should function as follows.

If the light is on and steady, it means that the pressure in one or more of the tires is too low, and if the light is flashing, then it indicates that one or more of the tires are over-inflated.

1. Turn the ignition key to the "On" or "Run" position but do not start the vehicle. (If the vehicle has an electronic keyless ignition then place the ignition switch in the "ACCY" position)

2. Press the "Lock" and "Unlock" buttons at the same time on the vehicles remote key fob, and keep holding the two buttons down until you hear the horn beep, and usually this takes around five seconds. The horn beep will indicate that the learn cycle has begun.

3. Re-learn the TPMS system. Deflate or inflate air into the driver-side front tire for approximately 8 to 10 seconds and then listen for the horn to beep one time. (the horn might beep before the 8 to 10 second re-learn, or it could even take as long as 30 seconds after)

4. Repeat steps 2 and 3 for the remaining three tires. Also, the remaining three tires must be checked in the exact following order, the passenger-side front tire, the passenger-side rear tire and finally the driver-side rear tire. After the final TPMS sensor has re-learned then the horn will beep twice.

5. Listen for the horn to beep twice. When the horn does beep twice, it wikll be the indicator that the TPMS system has re-learned and reset.

6. Turn the ignition switch to the "Off" position, and then be certain that all four tires have the correct tire pressure as recommended on the drivers door, and the next time that the ignition is turned on, the tire pressure light should be reset.

Let me know if you require any further assistance.

Hi and welcome to FixYa. I am Kelly.

Here are your service intervals:

NOTE Besides Oil changes there are inspection intervals I & II

http://www.savagebmw.com/Service/content_service_Intervals.htm

Inspection interval I

BMW Inspection I (return to top) Undercarriage

• Change engine oil and filter while engine is at normal operation temperature.
• Check transmission for leaks.
• Check rear axle for leaks.
• Visually check fuel tank, lines, and connections for leaks.
• Check condition, position, and mounting of exhaust system. Examine for leaks.
• Check power steering system for leaks.
• Check overall thickness of front and rear disc brake pads.
• Examine brake disc surfaces.
• Clean brake pad contact points in calipers.
• Grease wheel center hubs.
• Check steering for absence of play, condition of suspension track rods, front axle joints, steering linkage, and joint disc.
• Check front control arm bushing for wear.
• Check brake and clutch system connectors and lines for leaks, damage, and incorrect positioning.
• Check for free movement of the parking brake cables. Adjust parking brake if necessary.
• Check all tire pressures (including spare). Correct if necessary.
• Check condition of tires (outer surfaces (left/right)), tread wear and pattern; In case of uneven tread wear readjust wheel alignment if required.

Engine Compartment

• Read out diagnostic system
• Check engine cooling system/heater hose connections for leaks.
• Check coolant level and antifreeze protection level; add coolant if necessary.
• Check level of brake and clutch fluid in reservoir; add fluid if required.
• Check windshield washer fluid level and antifreeze protection. Fill up and/or correct if necessary.
• Check air conditioner for operation.
• Reset Service Indicator.

Body/Electrical Equipment

• Check battery electrolyte level and add distilled water if required.
• Perform batter load test.
• Check lighting system, i.e. headlights, foglights, parking, backup, license plate, interior (including map reading lights), glove box, flashlight, illuminated makeup mirrors, luggage compartment lights.
• Check instrument panel and dashboard illumination.
• Check all warning/indicator lights, check control.
• Check turn signals, hazard warning flashers, brake lights, horns, headlight dimmer/flasher switch.
• Check wiper and washer system(s); wiper blades, washer jet positions.
• Check condition and function of safety belts.
• Oil hood, trunk/tailgate, and door hinges.
• Grease hood, trunk/tailgate and door latches. Check operation of all latches.
• Check central locking/double lock.
• Replace microfilter or Acc. Cabin Filter.
• Check heater/air conditioner blower, rear window defogger.
• Check rear view mirrors
• Visually examine the SRS airbag units for torn cover, obvious damage or attachment of decals, decorations, or accessories.

Final Inspection

• Road test with check of brakes, suspension, steering, clutch/manual transmission or automatic transmission

Inspection interval II
BMW Inspection II (return to top) Undercarriage

• Change engine oil and filter while engine is at normal operation temperature.
• Check transmission for leaks.
• Check rear axle for leaks.
• Visually check fuel tank, lines, and connections for leaks.
• Check condition, position, and mounting of exhaust system. Examine for leaks.
• Check power steering system for leaks.
• Check overall thickness of front and rear disc brake pads.
• Examine brake disc surfaces.
• Clean brake pad contact points in calipers.
• Grease wheel center hubs.
• Check steering for absence of play, condition of suspension track rods, front axle joints, steering linkage, and joint disc.
• Check front control arm bushing for wear.
• Check brake and clutch system connectors and lines for leaks, damage, and incorrect positioning.
• Check for free movement of the parking brake cables. Adjust parking brake if necessary.
• Check all tire pressures (including spare). Correct if necessary.
• Check condition of tires (outer surfaces (left/right)), tread wear and pattern; In case of uneven tread wear readjust wheel alignment if required.
• Check thickness of parking brake linings.
• Half-shafts; check for leaks at flexible boots.
• Inspect entire body according to terms of rust prevention limited warranty.

Engine Compartment

• Read out diagnostic system
• Check engine cooling system/heater hose connections for leaks.
• Check coolant level and antifreeze protection level; add coolant if necessary.
• Check level of brake and clutch fluid in reservoir; add fluid if required.
• Check windshield washer fluid level and antifreeze protection. Fill up and/or correct if necessary.
• Check air conditioner for operation.
• Reset Service Indicator.
• Replace spark plugs (as applicable by year and model)
• Replace intake air cleaner element.

Body/Electrical Equipment

• Check battery electrolyte level and add distilled water if required.
• Perform batter load test.
• Check lighting system, i.e. headlights, foglights, parking, backup, license plate, interior (including map reading lights), glove box, flashlight, illuminated makeup mirrors, luggage compartment lights.
• Check instrument panel and dashboard illumination.
• Check all warning/indicator lights, check control.
• Check turn signals, hazard warning flashers, brake lights, horns, headlight dimmer/flasher switch.
• Check wiper and washer system(s); wiper blades, washer jet positions.
• Check condition and function of safety belts.
• Oil hood, trunk/tailgate, and door hinges.
• Grease hood, trunk/tailgate and door latches. Check operation of all latches.
• Check central locking/double lock.
• Replace microfilter or Acc Cabin Filter.
• Check heater/air conditioner blower, rear window defogger.
• Check rear view mirrors
• Visually examine the SRS airbag units for torn cover, obvious damage or attachment of decals, decorations, or accessories.

Final Inspection

• Road test with check of brakes, suspension, steering, clutch/manual transmission or automatic transmission

Service indicator lights if installed:

http://www.savagebmw.com/Service/content_service_IntervalsLED.htm

That should just about cover the works other than failures.

Thanks for using FixYa!

Kelly

Your best bet is to go HERE and signup for a free account then Downloading your Manual - service sheets, diagrams, parts lists etc.
Hyundai is one of the best with providing their customers with free information about the vehicles!!

I have D/L the manual, and the warning lamps on the instrument cluster are...
Left to right...(starting under temp. Gauge)

WITHOUT TRIP COMPUTER
11. Traction Control Indicator Light (If installed)

12. ABS Warning Light (If installed)

13. Seat Belt Warning Light

14. Oil Pressure Warning Light

15. Charging System Warning Light

16. Parking Brake/Brake Fluid Level Warning
Light

17. Malfunction Indicator Light (MIL)

18. SRS (Airbag) Warning Light

19. Trip Odometer/Odometer

20. Trip Odometer Reset Knob

21. Low Fuel Warning Light

WITH TRIP COMPUTER

7. Front Fog Indicator Light (If installed)

8. Door Ajar Warning Light

9. Trunk Lid Open Warning Light

10. Parking Brake/Brake Fluid Level Warning
Light

11. Malfunction Indicator Light (MIL)

12. Charging System Warning Light

13. Oil Pressure Warning Light

14. SRS (Airbag) Warning Light

15. Cruise Indicator Light (If installed)

16. Seat Belt Warning Light

17. ABS Warning Light (If installed)

18. Traction Control Indicator Light (If installed)

19. Automatic Transaxle Position Indicator Light
(Auto T/A only)

22. Low Fuel Warning Light


Thanks for using FixYa - a FixYa rating is appreciated!!