Where do I locate the fuse that operates the heating system?

Question edited for clarity.
Question moved from Spanish Car company 'Seat', pronounced See-At.

Check Fuse 13 (Heated Seats)

https://fuse-box.info/chevrolet/chevrolet-uplander-2005-2008-fuses-and-relay

..

Check for battery power on the orange wire pin D and ground (black wire) pin C- Brown wire pin B should be ignition hot on connector C1 on the Driver Climate Control Seat Module located under the driver seat. If you have power and ground, you may need to use a scan tool to see if there are any codes stored in the module. If the scan tool is unable to communicate with this module, it could either be a bad module or a network problem. If you are missing either battery, ignition hot, or ground- then repair as needed

Tried resetting fuse's ????? how do you reset a fuse ?

The climate control seat system is able to heat and cool the front seats. Each climate controlled seat is operated by push-buttons on the EATC module located on the instrument panel. Each front seat temperature is then monitored and controlled by the dual climate control seat module (DCSM) located on the passenger front seat track.
The climate controlled seat system contains the following components:

• EATC module
• DCSM
• Thermo-electric device (TED) and blower assembly within each front seat cushion and backrest
• Air filter (attached to each TED and blower assembly)
• Cushion and backrest manifolds
• Cushion and backrest foam pads
• Cushion and backrest trim covers
• YOUR best bet , take it to a qualified repair shop . Unless you have factory service repair info. an a professional scan tool , This heated an cooling seat system can set DTC'S - diagnostic trouble codes in the heated seat module .

Climate Controlled Seat System
NOTE: When installing a new dual climate control seat module (DCSM), it is necessary to carry out programmable module installation (PMI). For additional information, refer to Section 418-01 .


Both the driver and front passenger climate controlled seats are independently controlled electronically by the DCSM mounted to the bottom of the passenger seat cushion. The climate controlled seat system only operates with the engine running, however, if using a diagnostic tool to command the DCSM, diagnostic testing can be carried out with the ignition switch key ON engine OFF (KOEO). The system receives power from battery junction box (BJB) fuse 12 (30A) feeding battery voltage on circuit SBB12 (GN/RD) into DCSM C3305a pin F. The system also receives power from BJB fuse 11 (30A) feeding battery voltage on circuit SBB11 (BU/RD) into DCSM C3305a pin E.
If only one of the BJB fuses 11 or 12 open, both seats will remain operational because the power feed circuits are internally connected in the DCSM.
Both climate controlled seats operate independently. If a fault occurs setting a DTC specific to either climate controlled seat, only the affected seat will be disabled by the module and the other will remain operational.
The 4 switches (identified with seat icons) on the dual-zone electronic automatic temperature control (EATC) module activate each seat system setting and illuminate LEDs above each switch to indicate the operating mode, 3 LEDs for HIGH, 2 LEDs for MED or 1 LED for LOW. The push-buttons with the blue seat icon operate the seat cooling mode and the push-buttons with the red seat icon operate the seat heating mode. The climate controlled seat system is not equipped with auto-mode.
Each driver and front passenger seat cushion is equipped with a thermo-electric device (TED) assembly that includes a seat blower (fan motor, serviced as an assembly with the TED). Similarly, each driver and front passenger seat backrest is also equipped with its own TED assembly with blower. Cabin air is drawn through the blower and distributed to each of the TED modules located in the seat cushion and backrest. The TEDs then heat or cool the air. The air is then directed into the foam pad and manifold where it is distributed along the surface of the cushion and backrest of the seat. Once the system is activated, the DCSM uses a set of flexible algorithms to control the heating/cooling modes and the blower speed dependant on the EATC seat switch settings.

The TED uses a ''Peltier'' circuit of P-type and N-type semiconductors connected in series using copper electrical conductors. The semiconductors are sandwiched between 2 copper heat exchangers. When current is applied to the TED, one side releases energy as heat, while the opposite side absorbs energy and gets cold. By reversing the current flow, the hot and cold sides reverse.
NOTE: Avoid applying power directly to a TED for testing its operation. Doing so may cause damage to the TED or shorten its usable life.
The temperature differences between the individual heated and cooled settings is minimal. For example, it is difficult to distinguish between LOW COOL and MEDIUM COOL settings. Measuring seat temperature at different settings is possible by monitoring the DCSM PIDs using the diagnostic tool.
The EATC module communicates climate controlled seat commands to the DCSM using the medium speed controller area network (MS-CAN) communication bus. The MS-CAN bus is connected to the data link connector (DLC) for diagnostic use. No direct connection exists between the DCSM and EATC for the climate controlled seat switches. The climate controlled seats can be commanded using the diagnostic tool to verify both module communication on the MS-CAN bus and operation of the DCSM. This method may be useful for isolating a control switch concern. It should also be noted that because CAN bus communication is more robust and reliable than other methods, it may be possible to have limited module communication with one of the CAN bus circuits disconnected or shorted to ground. Refer to Section 418-00 for additional information concerning CAN bus communication.

System Description NEEL0216 MODELS WITHOUT POWER DOOR LOCKS NEEL0216S01 The rear window defogger system is controlled by the rear window defogger timer. The rear window defogger operates only for approximately 15 minutes. The rear window defogger switch is integral to the air control. Power is supplied at all times
to rear window defogger relay terminal 5
through 20A fuse [No. 25, located in the fuse block (J/B)]. With the ignition switch in the ON or START position, power is supplied
through 10A fuse [No. 5, located in the fuse block (J/B)]
to rear window defogger relay terminal 1, and
to rear window defogger timer terminal 1. Ground is supplied to air control (rear window defogger switch) terminal 8 and rear window defogger timer terminal 4 through body grounds M14 and M68. With the rear window defogger switch (located in air control) ON, ground is supplied
to rear window defogger timer terminal 3
through air control (rear window defogger switch) terminal 8. Rear window defogger timer terminal 2 then supplies ground to the rear window defogger relay terminal 2. With power and ground supplied, the rear window defogger relay is energized. Power is supplied
through terminal 3 of the rear window defogger relay
to rear window defogger terminal +. Rear window defogger terminal - is grounded through body ground R102. With power and ground supplied, the rear window defogger filaments heat and defog the rear window. When the system is activated, the rear window defogger indicator illuminates in the air control. Power is supplied
from rear window defogger relay terminal 3
to air control (rear window defogger switch) terminal 4. Air control terminal 8 is grounded through body grounds M14 and M68. MODELS WITH POWER DOOR LOCKS NEEL0216S02 The rear window defogger system is controlled by the smart entrance control unit. The rear window defogger operates only for approximately 15 minutes. The rear window defogger switch is integral to the air control. Power is supplied at all times
to rear window defogger relay terminal 5
through 20A fuse [No. 25, located in the fuse block (J/B)] and
to smart entrance control unit terminal 49
through 7.5A fuse [No. 28, located in the fuse block (J/B)]. With the ignition switch in the ON or START position, power is supplied
through 10A fuse [No. 5, located in the fuse block (J/B)]
to rear window defogger relay terminal 1 and
to smart entrance control unit terminal 27. Ground is supplied to air control (rear window defogger switch) terminal 8 and smart entrance control unit terminals 43 and 64 through body grounds M14 and M68. With the rear window defogger switch (located in air control) ON, ground is supplied
to smart entrance control unit terminal 14
through air control (rear window defogger switch) terminal 1. Smart entrance control unit terminal 37 then supplies ground to the rear window defogger relay terminal 2. With power and ground supplied, the rear window defogger relay is energized. Power is supplied
through terminal 3 of the rear window defogger relay
to rear window defogger terminal +.
Rear window defogger terminal - is grounded through body ground R102. With power and ground supplied, the rear window defogger filaments heat and defog the rear window. When the system is activated, the rear window defogger indicator illuminates in the air control. Power is supplied
from rear window defogger relay terminal 3
to air control (rear window defogger switch) terminal 4. Air control (rear window defogger switch) terminal 8 is grounded through body grounds M14 and M68

FUSE PANEL LOCATION
The fuse panel is located in the engine compartment. A label on the inside of the cover lists the fuse amperage and circuits protected.
volvo 850 fuses fuse panel layout service repair manual
FUSE PANEL IDENTIFICATION
Fig. 1: Fuse Panel Identification
Courtesy of Volvo Cars of North America.
WARNING: Always disconnect battery ground cable before servicing "high-current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician.
* 1 - 15 Amp
Fuel Injection, Distributor Ignition, Automatic Gearbox
* 2 - 15 Amp
Fuel Pump, Alarm System
* 3 - 10 Amp
Courtesy Lights, Oil Level Sensor
* 4 - Not Used (1993-95)
* 4 - 10 Amp (1996)
Electronic Start Inhibitor (Immobilizer)
* 5 - 30 Amp
ECC Blower (Speed 4)
* 6 - 25 Amp
Central Locking System, Alarm
* 7 - 15 Amp
Audio System (Amplifier)
* 8 - 25 Amp (1993-95)
Power Antenna, Trailer Connector
* 8 - 40 Amp (1996)
Electronic Start Inhibitor (Immobilizer)
* 9 - 30 Amp
ABS, Traction Control System
* 10 - Not Used (1993-95)
* 10 - 15 Amp (1996)
Heated Rear Seat (If Equipped)
* 11 - 30 Amp
Heated Rear Window & Side Mirrors
* 12 - 10 Amp
Brake Lights
* 13 - 15 Amp
Hazard Flashers, Headlight Flashers, Alarm
* 14 - 30 Amp
ABS, Traction Control System
* 15 - 10 Amp (1993-95)
Audio System, Courtesy Lights, Door Open Light, Trunk Light, Glove Box Light, Remote Control Central Locking System,
Oil Level Sensor, Seat Belt Reminder
* 15 - 10 Amp (1996)
Audio System, Courtesy Lights, Door Open Light, Trunk Light, Glove Box Light, Remote Control Central Locking System,
Oil Level Sensor, Seat Belt Reminder, Data Link Connector
* 16 - 30 Amp (1993-95) Accessories
* 16 - 30 Amp (1996)
Power Antenna, Trailer Connector, Accessories
* 17 - 10 Amp
Key Reminder
* 18 - 25 Amp (1993-95)
Heated Front Seats, Power Mirrors
* 18 - 15 Amp (1996) Front Fog Lamps
* 19 - 15 Amp
Left High Beam Headlight
* 20 - 15 Amp
Right High Beam Headlight, High Beam Indicator
* 21 - 15 Amp
Left Low Beam Headlight
* 22 - 15 Amp
Right Low Beam Headlight
* 23 - 10 Amp
Left Parking Light, License Light
* 24 - 10 Amp
Right Parking Light, Bulb Failure Warning Sensor
* 25 - 10 Amp
Rear Fog Lamps, Fog Lamp Indicator
* 26 - Not Used (1993-95)
* 26 - 25 Amp (1996)
Heated Front Seats, Power Mirrors
* 27 - 15 Amp
Back-Up Lights, Turn Signals
* 28 - 10 Amp
Cruise Control, Heated Rear Window, Seat Belt Reminder Light, Shiftlock, Bulb Failure Warning Sensor, Heated Rear Seat
* 29 - 15 Amp
ABS, Traction Control System
* 30 - 10 Amp
Cigarette Lighter
* 31 - 25 Amp
ECC, ECC Blower (Speeds 1-3)
* 32 - 10 Amp
Audio System, Remote Controlled Central Locking System
* 33 - 15 Amp (1993-95)
Power Seats, OBD Test Socket, Tailgate Washer/Wipe (Wagon)
* 33 - 15 Amp (1996)
Power Seats, Tailgate Washer/Wipe (Wagon)
* 34 - 25 Amp
Windshield Wiper/Washer, Horn, Headlight Washer/Wiper
* 35 - 10 Amp
Instrument Lights, Sun Roof, Traction Control System
* 36 - Not Used
* 37 - Circuit Breaker
Power Windows, Power Sun Roof
* 38 - Not Used
* 39 - Circuit Breaker
Drivers Power Seat
* 40 - Circuit Breaker
Passengers Power Seat
RELAY PANEL LOCATION
The relay panel is located at the left corner of the instrument panel.
i copied this off a volvo site Hope this helps

Heated Seats
This system allows the electrical heating of the front seats on passenger demand.
The components of the system are:

• the seat heating elements located in the seat cushion and backrest.
• the heated seat control switch, located on the seat side trim panel.
• temperature sensors located in the seat cushion heating elements.
• heated seat relay.

Do both front seat heaters not work ? Do you know how to test electrical circuits with voltmeter ?
PINPOINT TEST J: THE HEATED SEAT IS INOPERATIVE Test Step Result / Action to Take J1 CHECK HEATED SEAT SWITCH OPERATION

• Key in ON position.
• Press the heated seat switch on the driver and passenger seats.
• Are both heated seat switch indicators illuminated?

Yes
If both indicators illuminate, Go To Pinpoint Test K . If only one indicator illuminates, GO to J5 .

No
GO to J2 . J2 CHECK THE HEATED SEAT RELAY CIRCUITS

• Key in OFF position.
• Disconnect: Heated Seat Relay C3250 (located under the driver seat).
• Key in ON position.
• Measure the voltage at heated seat relay C3250-86, circuit 1003 (GY/YE), harness side and ground; and between C3250-30, circuit 566 (DG), harness and ground.
  
• Are the voltages greater than 10 volts?

Yes
GO to J3 .

No
REPAIR inoperative 1003 (GY/YE) or 566 (DG) circuit. TEST the system for normal operation. J3 CHECK HEATED SEAT RELAY GROUND CIRCUIT

• Key in OFF position.
• Measure the resistance between heated seat relay C3250-85, circuit 57 (BK), harness side and ground.
  
• Is the resistance less than 5 ohms?

Yes
GO to J4 .

No
REPAIR circuit 57 (BK). TEST the system for normal operation. J4 CHECK THE HEATED SEAT RELAY

• Install a fused jumper lead between heated seat relay 3250-30, circuit 566 (DG), harness side and heated seat relay C3250-87, circuit 1064 (YE/LB), harness side.
  
• Do both heated seat indicators illuminate when pressed?

Yes
INSTALL a new heated seat relay. TEST the system for normal operation.

No
REPAIR circuit 1064 (YE/LB) to switches. TEST the system for normal operation. J5 CHECK INOPERATIVE HEATED SEAT SWITCH INPUT

• Key in OFF position.
• Disconnect: Heated Seat Switch C320 (Driver) or C321 (Passenger) for the inoperative heated seat.
• Key in ON position.
• Measure the voltage between heated seat switch C320-2 (driver) or C321-2 (passenger), circuit 1064 (YE/LB), harness side and ground .
  
• Is the voltage greater than 10 volts?

Yes
GO to J6 .

No
REPAIR circuit 1064 (YE/LB). TEST system for normal operation. J6 CHECK CIRCUIT 57 (BK) FOR AN OPEN

• Measure the resistance between heated seat switch C320-4 (driver) or C321-4 (passenger), circuit 57 (BK), harness side and ground.
  
• Is the resistance less than 5 ohms?

Yes
INSTALL a new heated seat switch. TEST the system for normal operation.

No
REPAIR circuit 57 (BK). TEST the system for normal operation It's not that simple , being a fuse . It's probably the relay or the heating element .
PINPOINT TEST K: SEAT DOES NOT HEAT BUT THE HEATED SEAT INDICATOR ILLUMINATES WHEN PRESSED ? Does it ?
Your best bet would be to take to a qualified repair shop .
Do

The following checks and repairs can help you:
1. In the fuse box within the bonnet - check fuse number 22, if burnt, replace it
2. Check fuse 19 in the fuse box inside the car located under the dashboard on the driverside
3. If these steps don't help, the problem may be with the wiring and connection between the module and the seat cushion - inspect it
4. Check if the signal return on the circuit is adequately functioning - if the module is being informed of an active seat
5. If there is a problem - repair or replace the circuit and/or wiring.

Swap it with a relay you know to be good and see if it works again,pick a relay that is not important to the function of your car.

I will post it in 2 different posts because its too long DB

HEATED SEAT SYSTEM
Individually controlled driver and passenger side electrically heated front seats are available factoryinstalled optional equipment on this model, when it is also equipped with the power seat option. The heated seat system allows both the driver and the front seat passenger the option to select one of two seat heating ranges, Low or High, or to turn the individual seat heaters OFF using the heated seat switches located in the center lower bezel near the bottom of the instrument panel center stack. The heated seat switch circuit operates on ignition switched battery current supplied through a fuse in the junction block, only when the ignition switch is in the ON position.

The heated seat system consists of the following components

• Heated seat elements
• Heated seat sensors
• Heated seat module (or memory heated seat module)
• Heated seat switches.

The heated seat system also relies upon resources shared with other electronic modules in the vehicle over the Programmable Communications Interface (PCI) data bus network. The PCI data bus network allows the sharing of sensor information. This helps to reduce wire harness complexity, internal controller hardware, and component sensor current loads. At the same time, this system provides increased reliability enhanced diagnostics, and allows the addition of many new feature capabilities. For diagnosis of these electronic modules or of the PCI data bus network, the use of a DRB scan tool and the proper Diagnostic Procedures are recommended.

The electronic modules that may affect heated seat system operation are as follows:

• Body Control Module (BCM) - Refer to Body Control Module in Electronic Control Modules for more information.
• Heated Seat Module (HSM) - Refer to Heated Seat Module in Electronic Control Modules for more information.
• Memory Heated Seat Module (MHSM) - If the vehicle is equipped with the Memory System, refer to Memory Seat Module in Electronic Control Modules for more information.

Refer to Power Seats Premium I/III in the Contents of Wiring Diagrams for complete circuit diagrams. Following are general descriptions of the major components in the heated seat system.

The heated seat system will only operate when the ignition switch is in the ON position, and the surface temperature at the front seat heating element sensors is below the designed temperature set points of the system. The heated seat system will not operate in ambient temperatures greater than about 41 °C (105 °F) . The front seat heating elements and sensors are hard wired to the Heated Seat Module (HSM) or the Memory Heated Seat Module (MHSM).

The heated seat switches are hard wired to the Body Control Module (BCM). The BCM monitors the heated seat switch inputs, then sends heated seat switch status messages to the HSM or MHSM over the Programmable Communications Interface (PCI) data bus. The HSM or MHSM contains the control logic for the heated seat system. The HSM or MHSM responds to the heated seat switch status messages, ignition switch status messages, and the front seat heating element sensor inputs by controlling the output to the front seat heating elements through integral solid-state relays.

When a seat heater is turned ON, the sensor located on the seat cushion electric heater element provides the HSM or MHSM with an input indicating the surface temperature of the seat cushion. If the surface temperature input is below the temperature set point for the selected Low or High heated seat switch position, the HSM or MHSM energizes the integral solid-state relay, which supplies battery current to the heating elements in the seat cushion and back. When the sensor input indicates the correct temperature set point has been achieved, the HSM or MHSM de-energizes the solid-state relay. The HSM or MHSM will continue to cycle the solid-state relay as needed to maintain the temperature set point.

The HSM or MHSM and the seat heater elements operate on non-switched battery current supplied through the power seat circuit breaker in the junction block. However, the HSM or MHSM will automatically turn OFF the heating elements if it detects an open or short in the sensor circuit, a short or open in the heating element circuit causing an excessive current draw, or when the ignition switch is turned to the OFF position.

See the owner's manual in the vehicle glove box for more information on the features, use and operation of the heated seat system.

I WILL POST THE REST

Chances are that either your blower relay is bad or the instrument cluster on the dash is bad. Relay can be found by going to autozone and asking where it is and how much it costs.But chances are that it is located in the engine compartment back by the dash(firewall)