Question about 2005 Chevrolet Chevrolet Avalanche 1500 LS

1 Answer

How do i find wiring diagram for stop lights

Stop lights are not working

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 15,575 Answers

The STOP LP 25 A fuse in the underhood fuse block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to both the STOP 15 A fuse and the CHMSL 10 A fuse in the I/P fuse block, and to the turn signal/hazard module. The turn signal/hazard module then supplies voltage to both of the trailer rear turn/stop lamp supply voltage circuits. The voltage from the CHMSL 10 A fuse is to the center high mounted stop lamp (CHMSL) and the trailer jumper harness. The voltage from the STOP 15 A fuse is to the stop lamps, throttle actuator control (TAC) module, and the cruise control.
Do you know what a stop lamp switch is ? If so I would check it with a DVOM digital volt ohm meter , after you check fuse .
Did

Posted on Nov 05, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brakes lights stopped working


Check stop lamp fuse 1st, possible failed stop lamp/brake switch.

Jan 10, 2014 | Ford Ranger Cars & Trucks

1 Answer

My stop lights not working


faulty switch on the brake pedel. check for power going to and from .

Nov 26, 2012 | Ford Cars & Trucks

1 Answer

Hi beams, low beams, taillights, and dash lights stopped working.


Might want to check the fuses if you haven't already.

Oct 13, 2009 | 2000 Honda Civic

1 Answer

Tail Light and License Plate lights stopped working


With light switch on, test the wires leading up to the mentioned lights with a test light(cost about 5 or 6 bucks at wal-mart) that way u can eliminate any corrosion questions and get to the source quicker, if test light indicates that the wire is hot, than check connection areas for any wear and tear and possible carbon corrosion. Check lightbulbs, my license plate light stopped working and wire was hot, but wouldnt turn on due to the housing base, got too dryrotted and wouldnt function propery, had to rig it up, but works now.

Jun 08, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Turn signal lights stop working. Neither the right or left turn signal work. Heard a noise before it stop working. The flashing started slowing down and stop blinking. Now it doesn't work at all. What


most likely its the turn signal relay. which is under the hood. in the fuse box. also make sure ur running lights are working if they are connected to the turn signal.

May 08, 2009 | 1993 Nissan Pathfinder

1 Answer

2001 odyssey no tail lights but break lights work.


Check the lamps first to see if both are good, do a wiggle test to see if the lamp's socket is good(sometimes they get too hot and the contacts spread open). Next check fuses for the running lights and break lights. If the running lights work on the front but not on the back then its not a fuse its a ground issue. Use a stick or another person to depress the break pedal to check for power at the plug that goes to the stop/running light lamp.





Mar 18, 2009 | 2001 Honda Odyssey

1 Answer

RIGHT STOP LIGHT WORKS IRREGULARLY(2002 FORD WINDSTAR)


thereis three switches to check one is the muti function switch. the second is the headlight switch and third is the brake switch on the pedal.if not them check your ground and see if it is secured properly

Mar 07, 2009 | 2000 Ford Windstar

1 Answer

SIGNAL LIGHTS STOPPED WORKING, BRAKE LIGHTS STOPPED WORKING


does the high mount stop lamp work? Try turning the emergency flashers on and off a couple times

Feb 28, 2009 | 1995 Ford Explorer

1 Answer

Signal lights and brake lights stopped working


the multifunction switch (turn signal switch) is a major cuase of this. your high mount stop lamp wire is run through the switch.

Dec 21, 2008 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
2005 Chevrolet Chevrolet Avalanche 1500 LS Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...