What are the torque specs for front struts? - 1995 Buick LeSabre

front

1. Install or connect the following:
   • Strut assembly
   • Fork to the strut and torque the bolts to 59 ft. lbs. (80 Nm)
   • Fork to the lower arm and torque the bolt to 88 ft. lbs. (120 Nm)
   • Upper strut mounting nuts and torque to 36 ft. lbs. (50 Nm)
   • Brake hose bracket
   • Front wheel
2. Check and/or adjust the wheel alignment.

--------------------rear------------

To install:

1. Install or connect the following:
   • Strut assembly and mounting bracket and torque the bolt to 36 ft. lbs. (50 Nm)
   • Upper arm and rear carrier bolt and torque the bolt to 88 ft. lbs. (120 Nm)
   • Lower mounting bolt
   • Rear wheel

The torque specifications for the front suspension of a 1998 Lincoln Town Car will depend on the specific components that make up the suspension system.
Here are some of the common torque specifications for the front suspension of a 1998 Lincoln Town Car:

• Ball joint nut: 52 ft-lbs
• Control arm to frame bolt: 52 ft-lbs
• Control arm to spindle nut: 52 ft-lbs
• Stabilizer bar link nut: 28 ft-lbs
• Strut mount to steering knuckle bolt: 30 ft-lbs
• Strut to steering knuckle nut: 30 ft-lbs

It is important to note that these torque specifications are based on general information and may vary depending on the specific model of the Lincoln Town Car and the condition of the vehicle.
It is always recommended to consult a factory service manual or professional mechanic to obtain the most accurate torque specifications for your specific vehicle.

Question edited for clarity, MAKER.
Question moved to model category.

Torque spec question : 2000-2005 (other than GXP)

http://www.pontiacbonnevilleclub.com > topic52656
Jul 4, 2020 · 4 posts · 3 authors
Stabilizer bar link nut 13 ft.lbs. Strut mount nut 55 ft.lbs. Strut mount to body 35 ft.lbs. Strut to knuckle 135 ft. lbs.
2000 Torque Specs : Specifications and General Information
1 post
May 21, 2008
Quick Torque Specs Question : 2000-2005 (other than ...
2 posts
Sept 27, 2014
stupidly over done topic but need some questions answered
6 posts
Jun 17, 2016
Broken spring : 2000-2005 (other than GXP)
6 posts
May 19, 2019
More results from www.pontiacbonnevilleclub.com

2004 bonneville se: steering..torque specs for tie rod..strut..bolts

https://www.justanswer.com > ... > Pontiac Problems
Jun 22, 2010 - lbs.) Strut Mount to Body Nut, 47 Nm (35 ft. lbs.) Strut to Knuckle Nut, 147 Nm (108 ft.
1 answer · Top answer: Tie Rod Inner to Gear 100 Nm (74 ft. lbs.)Tie Rod (Front) Lock Nut 64 Nm

https://s12.postimg.org/troce06kd/front_macpherson_strut.jpg

Click on the link.
This is for your vehicle, front macpherson strut.
The specs should be in the text.

Hi Fred,here's a link on your struts. Repair Guides Front Suspension Struts macpherson Struts AutoZone com

Call the auto parts place that you purchased the struts from.

just tighten them by hand with a wrench pretty tight , just do not snap them off , you do not need the specs make them tight where as they will not back out , no bigger

This is for front suspension, 06 impala, 3.5L engine. It's a little small, maybe you can read it?

Thanks for using FixYa.

Stabilizer Links

Removal & Installation

1. Raise and support the vehicle.
2. Remove the front tire and wheel assembly.
3. Disconnect the stabilizer link from the stabilizer shaft.
4. Disconnect the stabilizer link from the strut assembly and remove from the vehicle.

To install:

1. Connect the stabilizer link to the strut assembly.
2. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
3. Connect the stabilizer link to the stabilizer shaft.
4. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
5. Install the front tire and wheel assembly.
6. Lower the vehicle.

Damper shaft nut-------- 40 ft lbs
strut upper mounting nut--- 40 ft lbs.
strut to steering knuckle bolts/nuts---
2001 and earlier models
step 1---- 37 ft. lbs.
step 2---- 66 ft lbs.
step 3---- Tighten an additional 45 to 60 degrees
2002 and later models
step 1---- 37 ft lbs.
step 2----73 ft lbs.
step 3---- Tighten an additional 30 to 45 degrees