I aready changed the ho2 sensor 1.why also start the engine after second check engine lights also come.i scandal the code also same.HO2S(S1)failure.how to fix for honda accord 2.0CC model SDA

there are about a dozen O2 sensor codes. Tell us which one you have

These code's don't have anything to do with ignition switch . What engine does it have ?
Engine Controls - 4.3L , 4.8L, 5.3L, and 6.0L
• DTC P0053 for HO2S bank 1 sensor 1
• DTC P0054 for HO2S bank 1 sensor 2
• DTC P0059 for HO2S bank 2 sensor 1
• DTC P0060 for HO2S bank 2 sensor 2
The heated oxygen sensor (HO2S) must reach operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensor to reach operating temperature. Voltage is provided to the heater by the ignition 1 voltage circuit through a fuse. With the engine running, ground is provided to the heater by the HO2S heater low control circuit, through a low side driver within the powertrain control module (PCM). The PCM commands the heater ON or OFF to maintain a specific HO2S operating temperature range. The PCM determines the temperature by measuring the current flow through the heater. When the heater is in the ON state, the PCM will pulse the heater OFF for a duration of 50 ms, once per second. The PCM calculates the heater resistance on a cold start. This diagnostic will only run once per ignition cycle. If the PCM detects that the heater calculated resistance is not within the expected range, the following DTCs will set:
With all these code's ,i would check O2 sensor's heater circuit power supply . Fuse blown .
O2 A & O2 B fuse's under hood fuse box , then check for melted wires on exhaust manifold or exhaust pipe .

DTC P0053 HO2S Heater Resistance Bank 1 Sensor 1
• DTC P0135 HO2S Heater Performance Bank 1 Sensor 1
Important: Whenever the heated oxygen sensor (HO2S) heaters are commanded ON with a scan tool, they will continue to be pulsed ON once per second until the ignition is turned OFF for 30 seconds.
Turn ON the ignition, with the engine OFF.
Command the HO2S heaters ON with a scan tool.
Wait 15 seconds to allow the HO2S heater current to stabilize.
Observe the affected HO2S Heater Current parameter with a scan tool.
Is the HO2S Heater Current parameter within the specified range?
0.25-1.375 A

code p 0136 refers to heated oxygen sensor (HO2S) 2 bank 1 ---circuit malfunction===causes ---heating inoperative ---wiring---HO2S--- ECM
also refers to oxygen sensor (O2S0 2 bank 1---circuit malfunction===causes --- wiring---O2S ---ecm
it also refers to heated oxygen sensor (HO2S) 2 bank 1 ---no signal===causes ---wiring --- HO2S---
code p 0137 refers to HO2S 2 bank 1 ---low voltage -===causes --exhaust leak---wiring short to ground ---HO2S--- ECM
it also refers to O2S 2 bank 1---low voltage ===causes exhaust leak---wiring short to ground ---O2S ---ECM
to set you up here-- there are 4 oxygen sensors in the system
2 are heated oxygen sensors (HO2S) on in each exhaust manifold or exhaust pipe before the cat converter and
2 oxygen sensors (O2S) -- one in each exhaust pipe after the cat converters
heated oxygen sensors have 4 wires and O2S sensors normally only 2 wires
it is more that possible that you changed the wrong sensors and in the process damaged the delicate wires with the incorrect spanner being used

MAKE SURE THE CONNECTIONS AT THE SENSOR ARE GOOD,ALSO CHECK FOR VACUUM LEAKS,HERE'S A LINK TO YOUR CODE,THE OLD SENSOR MAY BE GOOD,JUST A VACUUM LEAK, P1133 Chevrolet HO2S Insufficient Switching Bank 1 Sensor 1

Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
- Vacuum leak
- Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 harness is open or shorted
- Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 circuit poor electrical connection

The Powertrain Control Module (PCM) monitors the Heated Oxygen Sensor (HO2S) activity for 90 seconds after closed loop operation has begun. The PCM determines if the front HO2S is functioning properly by counting the number of HO2S-1 Lean/Rich (L/R) and Rich/Lean (R/L) switches.

If the Powertrain Control Module (PCM) determines that the front HO2S did not switch enough times, the PCM will set the P1133 code.

replace the o2 sensor

I’m happy to assist further over the phone at https://www.6ya.com/expert/brock_d67526d2a834c47e

P1133 CHEVROLET - HO2S Insufficient Switching Bank 1 Sensor 1http://engine-codes.com/p1133_chevrolet.htmlForum CodePossible causes- Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 shorted to Engine Control Module (ECM) ground
- Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
- Vacuum leak
- Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 connector and wires

code p 0130 refers to the heated oxygen sensor (HO2S) 1 bank 1
code p 0139 refers to HO2S 2 bank 1 the HO2S is the ones in the exhaust manifold or pipe before the cat converter

CODE PO151 - HO2S - 21 BANK 2 SENSOR 1 CIRCUIT LOW INPUT. CODE PO153- HO2S BANK 2 SENSOR 1 CIRCUIT SLOW RESPONSE. CODE P1151 - LACK OF HO2S - 21 SWITCHING HO2S SIGNAL LOW INPUT. POSSIBLE CAUSES TO YOUR PROBLEM AIR INTAKE SYSTEM LEAKING VACUUM HOSES LEAKING OR DAMAGED.AIR LEAKS LOCATED AFTER THE MAF SENSOR MOUNTING LOCATION OR IN THE PCV SYSTEM. YOU COULD HAVE BASE MECHANICAL FAULT LIKE LOW CYLINDER COMPRESSION , VALVE TIMING OFF.HO2S CIRCUITS WET OR OILY CORRODED OR POOR TERMINAL CONTACT. HO2S SIGNAL CIRCUIT OPEN SHORTED TO GROUND SHORTED TO POWER OR THE SENSOR HAS FAILED. LOW FUEL PRESSURE OR VECHICLE DRIVEN UNTIL IT WAS OUT OF FUEL. BEFORE REPLACING PCM CHECK ALL VACUUM HOSES ON INTAKE MANIFOLD. REPLACE FUEL FILTER. CHECK YOUR SPARK PLUGS. IF SPARK PLUGS OIL COATED PROBLEM IN THE ENGINE ITSELF. YOU HAVE WORN PISTON RINGS, WORN VALVE GUIDES AND WORN VALVE SEALS. IF PCM WAS BAD YOU WOULD HAVE FLASHING CHECK ENGINE LIGHT CAR WOULD RUN POORLY.YOU WILL HAVE FAULT PCM CODE IF PCM FAILED. YOUR PROBLEM IN HO2S SENSORS AND THE ENGINE AIR FUEL MIXTURE.

To retrieve OBDII Error codes from your Chrysler/Jeep/Dodge vehicle, do the following sequence with the key: ON-ACC-ON-ACC-ON and look at the odometer, that is where codes will be displayed. Here are the codes that you may/can get.

Ho2S = heated oxyen sensor, TP = throttle position, MAF = mass airflow, MAP = manifold absolute pressure, TC=turbocharger.P0030 HO2S Heater Control Circuit Bank 1 Sensor 1
P0031 HO2S Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 HO2S Heater Circuit High Voltage Bank 1 Sensor 1
P0036 HO2S Heater Control Circuit Bank 1 Sensor 2
P0037 HO2S Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 HO2S Heater Circuit High Voltage Bank 1 Sensor 2
P0050 HO2S Heater Circuit Bank 2 Sensor 1
P0051 HO2S Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 HO2S Heater Circuit High Voltage Bank 2 Sensor 1
P0056 HO2S Heater Circuit Bank 2 Sensor 2
P0057 HO2S Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 HO2S Heater Circuit High Voltage Bank 2 Sensor 2
P0100 MAF Sensor Ckt. Insufficient Activity
P0101 Mass Air Flow (MAF) Sensor Performance
P0102 Mass Air Flow (MAF) Sensor Circuit Low Frequency
P0103 Mass Air Flow (MAF) Sensor Circuit High Frequency
P0104 Mass Air Flow Circuit Intermittent
P0105 MAP Sensor Circuit Insufficient Activity
P0106 Manifold Absolute Pressure (MAP) System Performance
P0107 Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage
P0108 Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage
P0109 Manifold Absolute Pressure Circuit Intermittent
P0110 Intake Air Temperature (IAT) Sensor Circuit
P0111 Intake Air Temperature (IAT) Sensor Performance
P0112 Intake Air Temperature (IAT) Sensor Circuit Low Voltage
P0113 Intake Air Temperature (IAT) Sensor Circuit High Voltage
P0114 Intake Air Temperature Circuit Intermittent
P0115 Engine Coolant Temperature (ECT) Sensor Circuit
P0116 Engine Coolant Temperature (ECT) Sensor Performance
P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage
P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage
P0119 Engine Coolant Temperature Circuit Intermittent
P0120 Throttle Position System Performance
P0121 Throttle Position Sensor Circuit Insufficient Activity
P0122 Throttle Position (TP) Sensor Circuit Low Voltage
P0123 Throttle Position (TP) Sensor Circuit High Voltage
P0124 Throttle Position Sensor 1 Circuit Intermittent
P0125 Engine Coolant Temperature (ECT) Insufficient for Closed Loop Fuel Control
P0126 Insufficient Engine Coolant Temperature for Stable Operation
P0128 Coolant Thermostat
P0130 HO2S Circuit Closed Loop (CL) Performance Bank 1 Sensor 1
P0131 HO2S Circuit Low Voltage Bank 1 Sensor 1
P0132 HO2S Circuit High Voltage Bank 1 Sensor 1
P0133 HO2S Slow Response Bank 1 Sensor 1
P0134 HO2S Circuit Insufficient Activity Bank 1 Sensor 1
P0135 HO2S Heater Performance Bank 1 Sensor 1
P0136 HO2S Circuit Bank 1 Sensor 2
P0137 HO2S Circuit Low Voltage Bank 1 Sensor 2
P0138 HO2S Circuit High Voltage Bank 1 Sensor 2
P0139 HO2S Slow Response Bank 1 Sensor 2
P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2
P0141 HO2S Heater Performance Bank 1 Sensor 2
P0142 HO2S Circuit Bank 1 Sensor 3
P0143 HO2S Circuit Low Voltage Bank 1 Sensor 3
P0144 HO2S Circuit High Voltage Bank 1 Sensor 3
P0145 HO2S Circuit Bank 1 Sensor 2 Slow Response
P0146 HO2S Circuit Insufficient Activity Bank 1 Sensor 3
P0147 HO2S Heater Performance Bank 1 Sensor 3
P0150 HO2S Circuit Closed Loop (CL) Performance Bank 2 Sensor 1
P0150 HO2S Circuit Bank 2 Sensor 1
P0151 HO2S Circuit Low Voltage Bank 2 Sensor 1
P0152 HO2S Circuit High Voltage Bank 2 Sensor 1
P0153 HO2S Slow Response Bank 2 Sensor 1
P0154 HO2S Circuit Insufficient Activity Bank 2 Sensor 1
P0155 HO2S Heater Performance Bank 2 Sensor 1
P0156 HO2S Circuit Bank 2 Sensor 2
P0157 HO2S Circuit Low Voltage Bank 2 Sensor 2
P0158 HO2S Circuit High Voltage Bank 2 Sensor 2
P0159 HO2S Slow Response Bank 2 Sensor 2
P0160 HO2S Circuit Insufficient Activity Bank 2 Sensor 2
P0161 HO2S Heater Performance Bank 2 Sensor 2
P0162 HO2S Circuit Bank 2 Sensor 3
P0163 HO2S Circuit Bank 2 Sensor 3 Low Voltage
P0164 HO2S Circuit Bank 2 Sensor 3 High Voltage


P