Question about Pontiac Cars & Trucks
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.
Posted on Feb 14, 2009
The BCM program fuse on a 2005 Montanna SV6 is called something different in the manual. It's called a “Keyless Entry Module” fuse and it is fuse #7. The fuse panel is located on the passenger side on the side of the dash. There is a cover with an indent hole in it to pull the fuse cover off. It's really hard to pull it off and it almost seems like your going to break it when your trying to get if off. Keep pulling, it will come off! On the fuse cover, fuse #7 is labeled " RFA MDLS" which is again different than what is in the manual. I followed the procedure to reprogram my "Key Fob" and within 45secs, I had reprogrammed my key FOB! I was so excited, because, I have been trying locate the BCM fuse for 4 weeks. I think GMC does not want us to know it’s location or name, so you would have to go into a dealership to get your Key Fobs reprogrammed costing about a $100 for a minute of work.
1. Keep the windows open as a safety measure, then,
2. Remove the ignition key from the ignition lock cylinder.
3. Remove the “RFA MDLS” (fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) from the fuse panel.
4. Close all of the doors.
5. Close the liftgate.
6. Turn the ignition lock cylinder to ACC.
7. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
8. Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.
9. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
After 7 seconds, a chime may be heard confirming successful programming.
11. Repeat the previous step on each additional transmitter to be programmed.
12. Remove the ignition key from the ignition lock cylinder
13. Install the “RFA MDLS” fuse ( fuse #7 ,BCM PRGRM fuse, Keyless Entry fuse) back into the fuse panel.
14. Press on the key fob functions (EG. Lock, Unlock) to verify correct operation.
Posted on Jun 08, 2009
In the Glove compartment on the left hand side there is a black snap on cover pull it from the bottom and it will come open. There is 2 filters in this spot.
Posted on Jun 28, 2009
no that is only the older rear calipers on gm and others. the fronts do not have that style caliper and sound like the calipers are frozen and may be way your changing the pads. try opening the bleeder screw and then compressing them if they go then you need need brake hoses and if not you need calipers. god luck man
Posted on Dec 13, 2009
Tips for a great answer:
Mar 02, 2013 | 2006 Pontiac Montana SV6
Nov 05, 2012 | 2006 Pontiac Montana SV6
May 18, 2012 | 2006 Pontiac Montana SV6
Dec 05, 2010 | 2005 Pontiac Montana SV6
Nov 07, 2010 | 2005 Pontiac Montana SV6
Feb 15, 2010 | Pontiac Montana SV6 Cars & Trucks
Dec 07, 2009 | 2006 Pontiac Montana SV6
Jun 18, 2009 | 2005 Pontiac Montana
May 22, 2009 | 2006 Pontiac Montana SV6
105 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: