Sound Horn With Remote Key Lock feature is disabled in middle east virsions, what am trying to figure out is how to activate this feature, is there a missing module or a relay i should buy to fix.

I don't know about turning the alarm system off completely, but if you are trying to get it to stop chirping the horn and flashing the lights when locking/unlocking the doors, I found the following in the Ram 3500 Owner's Manual:

To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.

The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure:
1. Perform this operation while standing outside the vehicle.
2. Press and hold the LOCK button on a programmed (i.e. functional) key fob.
3. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. Release both buttons at the same time.
4. To reactivate this feature, repeat the above steps.

Vehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desired, this feature can be disabled by using the following procedure:
1. Perform this operation while standing outside the vehicle.
2. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob.
3. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the LOCK button. Release both buttons at the same time.
4. To reactivate this feature, repeat the above steps.

Sounds like a vehicle security module problem , but , without doing some testing that would be just a guess .
Checking for DTC'S - diagnostic trouble codes first ,then checking power an grounds to the module . Viewing wiring diagrams an testing electrical circuits for the locks too see if anything is wrong , missing power or grounds etc... Do you know what a wiring diagram is ? How to use a DVOM - digital volt ohm meter to test electrical circuits ? Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size. Under system click on body & accessories ,then under subsystem click on power locks . Click the search button then the blue link . If not familiar with automotive electronics your best bet mite be to take it to a qualified repair shop.

Power Lock
The power lock/unlock feature requests all of the vehicle doors, including the liftgate, be locked or unlocked upon a customer request from any interior door lock switch in the vehicle. The power door locking system functions independently of ignition status or vehicle speed. When the vehicle security module receives an unlock/lock command from any door lock control switch, the vehicle security module will activate relays internal to the module to supply the correct power and grounds for the door lock actuators.

Power Unlock Inhibit
NOTE: This feature is not enabled when the vehicle is delivered to the customer. If the customer requests this feature the module can be configured to enable this feature.
With the key in OFF, 20 seconds after electrically locked (remote transmitter, keypad, door lock control switch locked with door ajar) and all doors are closed, the door unlock switch will be inhibited if this feature is enabled. (The lock function will still operate.)
Deactivating/Activating Power Door Unlock Switch Inhibit
NOTE: The power door unlock switch inhibit feature needs to be enabled to perform this procedure.
This is customer configurable. Steps one through three must be completed within 30 seconds.

1. Turn the key to ON, then press UNLOCK three times.

1. Turn the key to OFF, then press UNLOCK three times.

1. Turn the key to ON, within five seconds press LOCK two times.

The user should receive two horn chirps to indicate the system has been disabled or two chirps followed by a horn honk to indicate the system has been enabled.
Pressing LOCK two times again will toggle the door lock control switch inhibit feature state.
Turn the key to OFF to exit programming mode.
This feature can also be enabled/disabled using a diagnostic tool.
Auto-lock Enable/Disable - Using the Ignition Switch
Another way to turn the auto-lock feature off/on is by following this series of steps:

1. Close all doors.

1. Confirm that the key is in the OFF position.

1. Turn the key from OFF to ON.

1. NOTE: Steps 4 through 8 must be carried out within 30 seconds. Press UNLOCK three times.

1. Turn the key from ON to OFF.

1. Press UNLOCK three times.

1. Turn the key from OFF to ON.

1. Verify that the horn chirps. This indicates the enable/disable mode and now is ready to accept program changes.

1. Press UNLOCK once to command the vehicle security module to toggle the auto-lock/relock feature OFF.

1. Press LOCK once to enter the command.

1. Verify that the horn chirps one time. There should only be one chirp indicating that the auto-lock/relock feature has been disabled. If one chirp is heard followed by a longer sound of the horn, the auto-lock/relock feature has just been enabled. Return to Step 10.

1. Turn the key to the OFF position to exit the enable/disable mode.

1. Exit the vehicle and verify that the horn chirps once to indicate that a feature has been changed and that auto-lock/relock has been disabled.

I have a 2004 Lincoln LS,disconnect the negative battery for 10 minutes,then connect cable back,when you open driver side door alarm will go off,insert key in ignition and alarm will go off.Get in car,lock all doors and windows,turn key to the right 8 times quickly,then doors will unlock,then quickly push any button on key fob.

The vehicle horns are activated under the following conditions:
?€¢
The horn switch is depressed.

?€¢
The body control module (BCM) commands the horns on. The BCM commands the horns on under either of the following conditions:

-
When the content theft deterrent system detects a vehicle intrusion. For further information, refer to Content Theft Deterrent (CTD) Description and Operation in Theft Deterrent.

-
When the panic button is depressed on the remote control door lock transmitter. For further information, refer to Keyless Entry System Description and Operation in Keyless Entry.

-
When the OnStar?® system is used to sound the horns, if equipped. For further information, refer to OnStar Description and Operation in Cellular Communications.

-
When the keyless entry system is used to lock the vehicle, a horn chirp may sound to notify the driver that the vehicle has been locked. The notification feature may be enabled or disabled through personalization. For further information, refer to Keyless Entry System Description and Operation in Keyless Entry

System Description
The horn system consists of the following components:
?€¢
HORN fuse

?€¢
Horn relay

?€¢
Horn slip ring

?€¢
Horn switch

?€¢
Horn assembly

?€¢
Body Control Module (BCM)

System Operation
The vehicle horn system is activated under the following conditions:
?€¢
The horn switch is depressed.

?€¢
The body control module (BCM) commands the horns on. The BCM commands the horns on under any of the following conditions:

-
When the panic button is depressed on the remote control door lock transmitter. For further information refer to Keyless Entry System Description and Operation .

-
When the keyless entry system is used to lock the vehicle, a horn chirp may sound to notify the driver that the vehicle has been locked. The notification feature may be enabled or disabled through personalization. For further information refer to Keyless Entry System Description and Operation .

there should be an info center on your car and it ask all the questions in you want the light on and how long horn or no horn valet lights or not

Trunk Lock After Closing
--------------------------
Desc.: What happens to the trunk lock when closing it.

Settings:
Yes: Automatically lock Boot on closing
No: Boot can be reopened using micro switch button located on the trunk/boot

* Trunk Lock After Drive Off
----------------------------
Desc.: Should the trunk be locked at drive off or after 30 sec.?

Settings:
Yes: Trunk/Boot will automatically lock when vehicle increases speed
No: Trunk/Boot will remain closed, however will be in the unlocked
condition if No was selected in the previous option.

* Door & Trunk Unlock at Key Out
--------------------------------
Desc.: When the is removed from the center console should door/trunk
be unlocked?

Settings:
Yes: All Doors & Trunk/Boot will Unlock when the Key is removed from
the Ignition Switch If Driver frequently locked all Doors when
driving
this feature would be beneficial.
No: Doors and Boot will remain in the same condition as they were
prior
to Key removal

* TSL Locking Logic (Theft Security Locking/Deadlock)
-------------------
Settings:
TSL at first Press: Default Setting. All Doors will lock in Deadlock
Mode
TSL at Second Press: All Doors will lock in Deadlock mode at the second
press of the Remote.

* Lock /Unlock Acknowledge
--------------------------
Settings:
None : No acknowledge will be visible
Indicators: Indicators will blink as acknowledge

* Follow Me Home Function
-------------------------
Settings:
Tail Light: When selected Tail Lights will be illuminated
Back Up Light: When Selected Reverse Light will be activated


Tech 2 Body Exterior Lighting & Horn
====================================

* High Beam Follow me home Active Time
--------------------------------------
Desc.: Follow Me Home Active Time can be adjusted between 0- 10 minutes

Settings:
This Feature can be turned on or Off .Yes / No can be selected.
Low Beam Automatic / Low Beam also in Position 0 (light switch)
Yes / No
Follow Me Home Active Time
- Daytime Driving Lights can be activated

* Parking Lights
----------------

Settings:
Act as Lead Me To the Car Light.

* Park Light On Reminder
------------------------
Settings:
On / Off
If Ignition is turned Off and the parking lights are active, Driver will
be warned if set to on.

* Show Trailer Light Outage
Desc.: REC will detect blown trailer light and display on SID

Settings:
Yes or No

* Trailer Light / Fog Light off
-------------------------------

Settings:
Yes: Fog Light Rear will be disabled When Trailer is connected Yes
No

* Horn Lock Unlock Acknowledge
------------------------------
Settings:
On: Horn will honk when car is locked
Off: Horn will not honk if car is locked


Tech 2 Body Locking
===================

* Panic Alarm Activation (Vehicles fitted with /Alarm only)
-----------------------------------------------------------
- Panic Button / Locking Switch
Central Locking Switch Driver /Passenger

Settings:
- Panic Button on Remote and locking switch inside vehicle will
activate alarm
- Panic Button will activate Alarm only
- Locking Switch inside vehicle (driver /passenger will activate
alarm only
- No Panic Alarm function required.

* Unlock Logic
--------------
Settings:
All at first press : All Doors will open & Fuel Lid will unlock if the
Driver or Passenger Door Switch is activated
Driver Door & Fuel Lid at first press : Only the drivers Door will unlock
& Fuel Lid will unlock when door
switch is activated

* Remote unlocking One Press
----------------------------
Settings:
All at first press: All Doors will open & Fuel Lid will unlock if the
Remote is pressed
Driver door & Fuel Lid at first press: Only the drivers Door will unlock &
Fuel Lid will unlock when the Remote
is pressed

Your lock settings were most probably changed from your remote unit. By pressing both lock and unlock keys together for around two to three seconds you can switch between silent mode and horn mode. Hooe that helps...

Deactivating/activating autolock
There are 3 methods to enable/disable this feature. One through your
dealer, the second with a power door unlock/lock sequence and the third
with the keypad.
Before following the activation or deactivation procedures, make sure
that the anti-theft system is not armed, ignition is off, and all vehicle
doors, liftgate and liftgate window are closed.
Controls and features
Power door unlock/lock
procedure
You must complete steps 1-5 within
30 seconds or the procedure will
have to be repeated. If the
procedure needs to be repeated,
you must wait 30 seconds.
1. Turn the ignition key to ON.
2. Press the power door unlock control three times.
3. Turn the ignition key from ON to OFF.
4. Press the power door unlock control three times.
5. Turn the ignition back to ON. The horn will chirp.
6. Press the unlock control, then press the lock control. The horn will
chirp once if autolock was deactivated or twice (one short and one long
chirp) if autolock was activated.
7. Turn the ignition to OFF. The horn will chirp once to confirm the
procedure is complete.
Keyless entry key pad procedure
1. Enter 5 digit entry code
2. Press and hold 7/8 control
3. Press and release 3/4 control
4. Release 7/8 control.
The user should receive a horn
chirp to indicate the system has
been disabled or a chirp followed by
a honk to indicate the system has
been enabled.
Smart unlock
This feature prevents the driver’s door from locking while the key is in
the ignition. This feature will unlock only the driver’s door if the key is in
the ignition cylinder, the driver’s door is ajar and all doors are locked
using the interior trim switch. If these conditions are met, the entire
vehicle will lock and the driver’s door will unlock within 1 second.
Controls and features
127